The driver puts the device into MAC loopback in two places in the
driver.  This patch consolidates the code into a single routine.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that CPMU devices don't do MAC loopback, all the CPMU power saving
mode adjustments are unneeded.  This patch removes the dead code.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are valid configurations where Max BW is configured to zero for
some VNs.
Print the message only if debugging is enabled and do not call the
configuration "illegal".

[v2: use DP(), not BNX2X_DBG_ERR(); recommended by Eilon Greenstein.]
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 9aa32835 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*

The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors).  In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.

We do not explicitly select the Kconfig dependencies, as this would force
EMAC on.  Doing it in the defconfig allows more flexibility.

Tested on a canyondlands board.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Korina.c is a MIPS-specific SOC driver and <asm/segment> is empty on
MIPS since 2.1.7 ...
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.

Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
	ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
	ndo_set_rx_mode but do not support uc filtering
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add pr_fmt(fmt) KBUILD_MODNAME ": " to prefix messages with "bnx2x: ".
Remove #define DP_LEVEL and use pr_notice.
Repeating KERN_<LEVEL> isn't necessary in multi-line printks.
printk macro neatening, use fmt and ##__VA_ARGS__.
Coalesce long formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Uses of pr_cont should be avoided where reasonably possible
because they can be interleaved by other threads and processes.

Coalesce pr_cont uses.

Fix typos, duplicated words and spacing in DP uses caused
by split multi-line formats.  Coalesce some of these
split formats.  Add missing terminating newlines to DP uses.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use %pM and mac address directly instead.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since sungem_phy is used by multiple, unrelated, drivers make it
build as a real module under drivers/net.

depmod will pick up the symbol dependency and make sure sungem_phy.ko
gets loaded any time sungem.ko or spider_net.ko is loaded.
Tested-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes build failures of the spider_net driver because it tries
to use a convoluted path to include this header.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the move of the Ethernet drivers into drivers/net/ethernet/
there was some leftover cleanup to do in the Kconfig and Makefile.

Removed the 10/100, 1000, and 10GbE Kconfig menus.

Removed the out-dated pci-skeleton.c file which was used an
example driver.  With the current networking features and
structure, the file is no longer a good example to use for
driver creation.

CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on feedback from Alan Cox, the acenic driver moved to
drivers/net/ethernet/alteon/ and made the necessary Kconfig and
Makefile changes.

CC: Jes Sorensen <jes@trained-monkey.org>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Tilera driver into drivers/net/ethernet/tile and
make the necessary Kconfig and Makefile changes.

Updated the Kconfig so that the options defualt to y if TILE kernel.

CC: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Xircom driver into drivers/net/ethernet/xircom/ and
make the necessary Kconfig and Makefile changes.

CC: <psheer@icon.co.za>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Renesas driver into drivers/net/ethernet/renesas/ and make
the necessary Kconfig and Makefile changes.

CC: Yoshihiro Shimoda <yoshihiro.shirmoda.uh@renesas.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the netx driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.

CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Move the Davicom driver into drivers/net/ethernet/davicom/ and
make the necessary Kconfig and Makefile changes.

CC: Ben Dooks <ben@simtec.co.uk>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Move the Microchip driver into drivers/net/ethernet/microchip/ and
make the necessary Kconfig and Makefile changes.

CC: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Aeroflex Gaisler driver into drivers/net/ethernet/aeroflex/
and make the necessary Kconfig and Makefile changes.

CC: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Avionic driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.

CC: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Dave Ethernet driver into drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.

CC: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the HP driver into drivers/net/ethernet/hp/ and
made the necessary Kconfig and Makefile changes.

CC: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Adaptec driver into drivers/net/ethernet/adaptec/ and make
the necessary Kconfig and Makefile changes.

CC: Ion Badulescu <ionut@badula.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the nForce driver into drivers/net/ethernet/nvidia/ and make
the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Myson driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.

CC: Donald Becker <becker@scyld.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the RDC driver into drivers/net/ethernet/rdc/ and make the
necessary Kconfig and Makefile changes.

CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Atmel driver into drivers/net/ethernet/cadence/ and
make the necessary Kconfig and Makefile changes.

CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Move the Analog Devices Inc driver into drivers/net/ethernet/adi/ and
make the necessary Kconfig and Makefile changes.

CC: <uclinux-dist-devel@blackfin.uclinux.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NBob Liu <bob.liu@analog.com>

Move the Lantiq driver into drivers/net/ethernet/ and the
necessary Kconfig and Makefile changes.

CC: John Crispin <blogic@openwrt.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NJohn Crispin <blogic@openwrt.org>

Move the MIPS drivers into drivers/net/ethernet/ and
make the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the IDT driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes

CC: "IDT Inc." <rischelp@idt.com>
CC: Felix Fietkau <nbd@openwrt.org>
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the IC Plus driver into drivers/net/ethernet/icplus/ and
make the necessary Kconfig and Makefile changes.

CC: <craig_rich@sundanceti.com>
CC: <sorbica@icplus.com.tw>
CC: <jesse@icplus.com.tw>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Xilinx drivers into drivers/net/ethernet/xilinx/ and
make the necessary Kconfig and Makefile changes.

CC: John Williams <john.williams@petalogix.com>
CC: "David H. Lynch Jr." <dhlii@dlasys.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the JME driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.

CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Cavium driver to drivers/net/ethernet/octeon/ and
make the necessary Kconfig and Makefile changes.

CC: David Daney <david.daney@cavium.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NDavid Daney <david.daney@cavium.com>

Move the packet engine drivers to drivers/net/ethernet/packetengines/
and the necessary Kconfig and Makefile changes.

CC: Donald Becker <becker@scyld.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>