mmc_request_done should be called at the end of handling a request, not
between the data and initial command parts of the request.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no reason for the PXAMCI debug code to print so many lines - it
causes the kernel buffer to overflow when trying to debug this driver.
Remove some debug messages which are duplicated by core code, and
combine other messages, resulting in fewer characters written to the
kernel log.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Always send a stop command at the end of a data transfer.  If we avoid
sending the stop command, some cards remain in data transfer mode, and
refuse to accept further read/write commands.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The CSD contains a "read2write factor" which determines the multiplier to
be applied to the read timeout to obtain the write timeout.  We were
ignoring this parameter, resulting in the possibility for writes being
timed out too early.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Pavel Pisa

The clock starting imxmci_start_clock() function contains hardware
issue workaround, which repeats start attempt, if SDHC does not react on
the first trial. But the second start attempt can be taken even, if the
first succeed and test code misses time limited clock running phase
due to delay caused by schedule to other task or some another device
interrupt. This change enables to detect such situation.
The performance is not issue, because usually at full clock rate
only about six loops in delay cycle are needed.
Signed-off-by: NPavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [PATCH] powerpc: update cell_defconfig
  [PATCH] spufs: Disable local interrupts for SPE hash_page calls.
  [PATCH] powerpc: Add cputable entry for POWER6
  [PATCH] ppc32 CPM_UART: Fixed odd address translations
  [PATCH] ppc32: Update board-specific code of the CPM UART users
  [PATCH] ppc32 CPM_UART: Convert to use platform devices
  [PATCH] ppc32: odd fixes and improvements in ppc_sys
  [PATCH] powerpc: Wire up *at syscalls
  [PATCH] ppc32: add 440GX erratum 440_43 workaround
  [PATCH] powerpc: Use check_legacy_ioport() on ppc32 too.
  [PATCH] powerpc64: Fix loading of modules without a .toc section
  [PATCH] sound/ppc: snd_pmac_toonie_init should be __init
  powerpc/pseries: Tell firmware our capabilities on new machines
  [PATCH] powerpc: Fix pagetable bloat for hugepages

Content of file au1200fb.c was duplicated. Remove.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Let people enable the advansys driver on x86-32, even though it's broken
on other architectures due to missing DMA mapping infrastructure.

It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and
possibly others.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The FXSAVE information leak patch introduced a bug in FP exception
handling: it clears FP exceptions only when there are already
none outstanding.  Mikael Pettersson reported that causes problems
with the Erlang runtime and has tested this fix.
Signed-off-by: NChuck Ebbert <76306.1226@compuserve.com>
Acked-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

reflect the changes to Kconfig since the last update.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch disables and saves local interrupts during
hash_page processing for SPE contexts.

We have to do it explicitly in the spu_irq_class_1_bottom
function. For the interrupt handlers, we get the behaviour
implicitly by using SA_INTERRUPT to disable interrupts while
in the handler.
Signed-off-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add a cputable entry for the POWER6 processor.

The SIHV and SIPR bits in the mmcra have moved in POWER6, so disable
support for that until oprofile is fixed.

Also tell firmware that we know about POWER6.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

transfer_objects should only be called when all of the cpus in the
node are online.  CPU_DEAD notifier callback marks l3->shared to NULL.
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add help text in Kconfig
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

As reported in Bugzilla Bug 6406, resume from S3 results in a blank screen.

For the IBM Thinkpad X30 using vesafb as the console driver, successful resume
from S3 requires option acpi_sleep=s3_bios,s3_mode.  Update documentation.

I would presume that, in any hardware, using vesafb as the console driver will
require as a minimum s3_mode.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Cc: <igor47@uchicago.edu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add sys_set_robust_list, sys_get_robust_list, sys_splice, sys_sync_file and
sys_tee system calls.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Generate new sysfs-attribute 'uid' that contains an device specific unique
identifier.  This can be used to identity multiple ALIASES of the same
physical device (PAV).  In addition the sysfs-attributes 'vendor' (containing
the manufacturer of the device) and 'alias' (identify alias or base device) is
added.  This is first part of PAV support in LPAR (also valid on zVM).
Signed-off-by: NHorst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add a read_mostly section and define __read_mostly to prevent cache line
pollution due to writes for mostly read variables.  In addition fix the
incorrect alignment of the cache_line_aligned data section.  s390 has a
cacheline size of 256 bytes.
Signed-off-by: NChristian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In case of an instruction processing damage (IPD) machine check in kernel mode
the resulting action is always to stop the kernel.  This is not necessarily
the best solution since a retry of the failing instruction might succeed.  Add
logic to retry the instruction if no more than 30 instruction processing
damage checks occured in the last 5 minutes.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Print a warning with the z/VM error code if segment_load, segment_type or
segment_save fail to ease the problem determination.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Added some changes that where proposed by Andrew Morton.  Added 3592 device
type.
Signed-off-by: NStefan Bader <shbader@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for atomic futex operations.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With CONFIG_SLAB_DEBUG=y networking over qeth doesn't work.  The problem is
that the qib structure embedded in the qeth_irq structure needs an alignment
of 256 but kmalloc only guarantees an alignment of 8.  When using SLAB
debugging the alignment of qeth_irq is not sufficient for the embedded qib
structure which causes all users of qdio (qeth and zfcp) to stop working.
Allocate qeth_irq structure with __get_free_page.  That wastes a small amount
of memory (~2500 bytes) per online adapter.
Signed-off-by: NChristian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The dasd state machine is not designed to enable an unformatted device, since
'unformatted' is a final state.  The BIODASDENABLE ioctl calls
dasd_enable_device() which never returns if the device is in this special
state.  Return -EPERM in dasd_increase_state for unformatted devices to make
dasd_enable_device terminate.  Note: To get such an unformatted device online
it has to be re-analyzed.  This means that the device needs to be disabled
prior to re-enablement.
Signed-off-by: NHorst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Avoid memory allocation with GFP_KERNEL in qdio_establish/qdio_shutdown.  Use
memory pool instead.  (Otherwise this can lead to an I/O stall where qdio
waits for a free page and zfcp waits for end of error recovery in low memory
situations.)
Signed-off-by: NAndreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If a signal handler has been established with the SA_ONSTACK option but no
alternate stack is provided with sigaltstack(), the kernel still tries to
install the alternate stack.  Also when setting an alternate stack with
sigalstack() and the SS_DISABLE flag, the kernel tries to install the
alternate stack on signal delivery.  Use the correct conditions sas_ss_flags()
to check if the alternate stack has to be used.
Signed-off-by: NLaurent Meyer <meyerlau@fr.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Interrupts can stay disabled if an error occurred in _chp_add().  Use
spin_unlock_irq on the error paths to reenable interrupts.
Signed-off-by: NStefan Bader <shbader@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a race condition in the I/O termination logic.  The race can cause I/O to
a dasd device to fail with no retry left after turning one channel path to the
device off and on multiple times.
Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix resume_execution() to handle iret and absolute jump opcode correctly on
i386.
Signed-off-by: NMasami Hiramatsu <hiramatu@sdl.hitachi.co.jp>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Yumiko Sugita <sugita@sdl.hitachi.co.jp>
Cc: Satoshi Oshima <soshima@redhat.com>
Cc: Hideo Aoki <haoki@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When trap happens in user space, kprobe_exceptions_notify() funtion will
skip it.  This patch deletes some unnecessary code for VM_MASK judgement in
eflags.
Signed-off-by: Nbibo, mao <bibo.mao@intel.com>
Cc: Masami Hiramatsu <hiramatu@sdl.hitachi.co.jp>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: N"Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Acked-by: NPrasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Yumiko Sugita <sugita@sdl.hitachi.co.jp>
Cc: Satoshi Oshima <soshima@redhat.com>
Cc: Hideo Aoki <haoki@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Running abnormal VM splits causes weird problems - people can set non-standard
splits by accident, then lots of time gets wasted diagnosing it - see the long
"[stable] 2.6.16.6 breaks java...  sort of" email thread.

So we need to make this option harder to set.  Use CONFIG_EMBEDDED for this.

CONFIG_EMBEDDED isn't really the right thing to use, but there's nothing else
obvious and avoiding these problems is more important than Kconfig purity.
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

CPU_HOTPLUG has race conditions when we use broadcast mode IPI.

- First we introduced no_broadcast option
    (see include/asm-i386/mach-default/mach_ipi.h)

- x86_64 solved it by using physical flat mode (same as bigsmp on i386)
  since this will not use broadcast shortcuts for IPI.

- We switched to use bigsmp on i386 so that we can have same handling as
  x86_64, but apparently this caused an error message, if kernel was
  compiled without X86_GENERICARCH, X86_BIGSMP.  The message "You have >8
  CPUS..." which was bogus and misleading, and only indicated one of the
  above ARCH wasnt selected.

So we do not switch to automatic bigsmp for HOTPLUG_CPU support in i386
until the other related config dependencies for SMP_SUSPEND etc can be done
right.
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

These messages are kinda silly..

CPU#0 had 0 usecs TSC skew, fixed it up.
CPU#1 had 0 usecs TSC skew, fixed it up.

inspired from: http://bugzilla.kernel.org/attachment.cgi?id=7713&action=viewSigned-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A regression in the ALSA driver compared to the OSS driver was reported as
ALSA bug #1520, so let's keep the OSS driver for now.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

this fixes coverity id #489.

Since the last element in the array is always ARRAY_SIZE-1 we have to check
for ipcnum >= ARRAY_SIZE()
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If compiled into the kernel, parport_register_driver() is called before the
parport driver has been initalised.

This means that it is expected that tp_count is 0 after the
parport_register_driver() call() - tipar's attach function will not be
called until later during bootup.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Add new SA_PROBEIRQ which suppresses the new sharing-mismatch warning.
  Some drivers like to use request_irq() to find an unused interrupt slot.

- Use it in i82365.c

- Kill unused SA_PROBE.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There's an off-by-1 in kernel/power/main.c:state_store() ...  if your
kernel just happens to have some non-zero data at pm_states[PM_SUSPEND_MAX]
(i.e.  one past the end of the array) then it'll let you write anything you
want to /sys/power/state and in response the box will enter S5.
Signed-off-by: Ndean gaudet <dean@arctic.org>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Current address translation methods can produce wrong results, because
virt_to_bus and vice versa may not produce correct offsets on dma-allocated
memory. The right way is, while tracking both phys and virt address of the
window that has been allocated for boffer descriptors, and use those
numbers to compute the offset and make translation properly.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This has the relevant updates/additions to the BSP code so that proper
platform_info struct well be passed to the CPM UART drivers. The changes
covered mpc866ads, mpc885ads and mpc8272ads.
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>