It is necessary to wait for bus power before sending
any commands.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Data transfers on third OMAP3 MMC controller don't work
because DMA line numbers are only defined for MMC1 and MMC2.
Fix that and store line numbers in mmc_omap_host structure
to reduce code size.
Tested on OMAP3 pandora board.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Turn off the bus power at suspend.
Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Allow slot_name to be the same as the other OMAP
driver, by removing the redundant "slot:" prefix.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Instead of using the bounce buffer, using scatter-gather emulation
(as in the OMAP1/2 MMC driver) removes the need of one extra memory
copy and improves performance.
Signed-off-by: NJuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some MMC commands result in the card becoming busy after
the response is received.  This needs to be specified
for the omap_hsmmc host controller, which is what this
patch does.  However, the effect is that some commands
with no data will cause a Transfer Complete (TC) interrupt
in addition to the Command Complete (CC) interrupt.
In order to deal with that, the irq handler has needed
a few changes also.

The benefit of this change is that the omap_hsmmc host
controller driver now waits for the TC interrupt while
the card is busy, so the mmc_block driver needs to poll
the card status just once instead of repeatedly.
i.e. the net result is more sleep and less cpu.

The command sequence for open-ended multi-block write
with DMA is now:

	Issue write command CMD25
	Receive CC interrupt
	Data is sent
	Receive TC interrupt (DMA is done)
	Issue stop command CMD12
	Receive CC interrupt
	Card is busy
	Receive TC interrupt
	Card is now ready for next transfer
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Most registers lose its state when the processor wakes up from sleep state.
Thus registers should be initialized, when the processor wakes up. However the
current hsmmc 'resume' function doesn't consider this issue and finally makes
deadlock. So this patch fixes this problem.
Signed-off-by: NKim Kyuwon <chammoru@gmail.com>
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Remove code that turns MMC1 power back on after it
has been powered off (when the voltage is 1.8V).

The offending code is not necessary because the
host controller bus voltage is initialized to
3V when probing or resuming.  Note that MMC powers up
with the highest voltage available (see mmc_power_up())
which will be 3V also.
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Replace the infinite 'while() ;' loops
with a finite loop version.
Signed-off-by: NJean Pihet <jpihet@mvista.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Timeouts during a command that has a data phase can result in the next
command issued after the command that failed not being processed, i.e.  no
interrupt ever occurs to indicate the command has completed.  This failure
can result in a deadlock.

This patch resets the data state machine to clear the error in case of a
command timeout.

Tested on OMAP3430 chip and intensive MMC/SD device removal while
transferring data.
Signed-off-by: NAndy Lowe <alowe@mvista.com>
Signed-off-by: NJean Pihet <jpihet@mvista.com>
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Based on a patch from Tony Lindgren ... after initialization,
never change HCTL.SDVS except for MMC1.  The other controller
instances only support 1.8V in that field, although they can
suport other card/SDIO/eMMC/... voltages with level shifting
solutions such as external transceivers.

MMC2 behavior sanity tested on Overo/WLAN, OMAP3430 SDP, and
custom hardware.  MMC1 also sanity tested on those platforms
plus Beagle.  This also fixes a bug preventing MMC2 (and also
presumably MMC3) from powering down when requested.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Work around lockdep issue when card detect IRQ handlers run in
thread context ... it forces IRQF_DISABLED, which prevents all
access to twl4030 card detect signals.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

... rather than the clock names themselves.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add omap hsmmc controller for 2430 and 34xx.

Note that this controller has different registers compared to
the earlier omap MMC controller, so sharing code currently is
not possible.

Various updates and fixes from linux-omap list have been
merged into this patch.

Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>