For drive side cable detection to work correctly, drives need to be
identified backwards such that the slave device releases PDIAG- before
the mater drive tries to detect cable type.  ata_bus_probe() was fixed
by commit f31f0cc2 but the new EH path
wasn't fixed.  This patch makes new EH path do IDENTIFY backwards.

ata_dev_configure() for new devices are still performed master first.
This is to keep the detection messages in forward order.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

   There is a HW issue in ATI SB600 SATA that PxSERR.E should not be
set on some conditions, for example, when there is no media in SATA
CD/DVD drive or media is not ready, AHCI controller fails to execute
ATAPI commands and reports PORT_IRQ_TF_ERR, but ATI SB600 SATA
controller sets PxSERR.E at the
same time, which is not necessary.
    This patch is just to ignore the INTERNAL ERROR in such case.
Without this patch, ahci error handler will report many errors as
below:
    ----------- cut from dmesg -----------
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0
        res 51/24:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
        res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error)
    -------- end cut ---------
Signed-off-by: NConke Hu <conke.hu@amd.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Not yet ready to turn on ATA ACPI by default, for either PATA or SATA.

Also, rename the global-scope module parameter variable 'noacpi' to
something more libata-specific, reducing the potential for namespace
collision.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The user can generate console output if they cause do_mmap() to fail
during sys_io_setup().  This was seen in a regression test that does
exactly that by spinning calling mmap() until it gets -ENOMEM before
calling io_setup().

We don't need this printk at all, just remove it.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] gdth: fix oops in gdth_copy_cmd()
  [SCSI] mptsas: Fix oops for insmod during kexec
  [SCSI] lpfc: avoid double-free during PCI error failure

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (5472): Isl6421: don't reference freed memory
  V4L/DVB (5441): Saa7146: Fix allocation of clipping memory
  V4L/DVB (5421): Fix suspend/resume in msp3400 and tuner
  V4L/DVB (5415): Msp_attach must return 0 if no msp3400 was found.
  V4L/DVB (5408): Fix SECAM handling on saa7115
  V4L/DVB (5400): Core: fix several locking related problems
  V4L/DVB (5390): Radio: Fix error in Kbuild file
  V4L/DVB (5332): Ir_rc5_timer_end decoder lockup fix

* git://kvm.qumranet.com/home/avi/kvm:
  KVM: always reload segment selectors
  KVM: Prevent system selectors leaking into guest on real->protected mode transition on vmx

This reverts commit 94985134 and
insteads removes the WARN_ON() that caused that commit in the first
place.

The problem is that we call disable_nonboot_cpus() in swsusp before
powering down the system in order to avoid triggering the WARN_ON()
in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping() and this doesn't
work well on Thomas' system.

So instead, remove the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:
init_low_mapping(), which triggers every time during the suspend to disk
in the platform mode, as the potential problem it is related to doesn't
seem to occur in practice.

[ I think we might want to disallow the case of multiple users of that
  mm, or something.  Normally, playing with the current process page
  tables on the current CPU should be fine as long as we don't have
  other threads using those tables at the same time..

  Anyway, not pretty, but better than the warning or the lockup - Linus ]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The clockevents / tick management code expects an error value, when the
event is already expired. hpet_next_event() returns 1 in that case.

Fix it to return the proper -ETIME error code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
  Export __splice_from_pipe()
  2/2 splice: dont readpage
  1/2 splice: dont steal
  make elv_register() output atomic
  block: blk_max_pfn is somtimes wrong

Without attached patch against current -git I get following with
!PROC_SYSCTL (with EMBEDDED and PROC_FS set):

    CC      init/version.o
    LD      init/built-in.o
    LD      vmlinux
  fs/built-in.o: In function `do_proc_sys_lookup':
  proc_sysctl.c:(.text+0x26583): undefined reference to `sysctl_head_next'
  fs/built-in.o: In function `proc_sys_revalidate':
  proc_sysctl.c:(.text+0x265bb): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_readdir':
  proc_sysctl.c:(.text+0x26720): undefined reference to `sysctl_head_next'
  proc_sysctl.c:(.text+0x267d8): undefined reference to `sysctl_head_finish'
  proc_sysctl.c:(.text+0x268e7): undefined reference to `sysctl_head_next'
  proc_sysctl.c:(.text+0x26910): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_write':
  proc_sysctl.c:(.text+0x2695d): undefined reference to `sysctl_perm'
  proc_sysctl.c:(.text+0x2699c): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_read':
  proc_sysctl.c:(.text+0x269e9): undefined reference to `sysctl_perm'
  proc_sysctl.c:(.text+0x26a25): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_permission':
  proc_sysctl.c:(.text+0x26ad1): undefined reference to `sysctl_perm'
  proc_sysctl.c:(.text+0x26adb): undefined reference to `sysctl_head_finish'
  fs/built-in.o: In function `proc_sys_lookup':
  proc_sysctl.c:(.text+0x26b39): undefined reference to `sysctl_head_finish'
  make: *** [vmlinux] Virhe 1

All those functions are in fs/proc/proc_sysctl.c, which has no CONFIG_
#define's in it, so the patch makes the compilation of that file to depend
on CONFIG_PROC_SYSCTL (the simplest choice).
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Because i don't have much time lately and my responses are pretty slow
it's probably best to remove me from MAINTAINERS to give someone else
the chance to jump in.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When CONFIG_IPC_NS=n, clone(CLONE_NEWIPC) claims success, but did not actually
clone a new IPC namespace.

Fix this to return -EINVAL so the caller knows his request was denied.
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I2O subsystem has been broken in mainstream several months ago (after
2.6.18).  Commit 4aff5e23 from Jens
Axboe split struct request ->flags into two parts: cmd_type and
cmd_flags.

In i2o layer this patch has replaced flag REQ_SPECIAL by the according
cmd_type.  However i2o has used REQ_SPECIAL not as command type but as
driver-specific flag for the debug purposes.  As result all i2o requests
have type "special" now, are not processed to the hardware and fail with
I/O error:

   i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0
  Buffer I/O error on device i2o/hda, logical block 0
  Buffer I/O error on device i2o/hda, logical block 0
   unable to read partition table
  block-osm: device added (TID: 207): i2o/hda

The following patch removes the extra debug checks without any drawbacks and
restores the normal driver's work.
Signed-off-by: NVasily Averin <vvs@sw.ru>
Acked-by: NMarkus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  drivers/pcmcia/au1000_generic.c: In function 'au1x00_pcmcia_socket_probe':
  drivers/pcmcia/au1000_generic.c:375: error: 'struct device' has no member named 'dev'
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:eisa_root_register from .text between 'pci_eisa_init' (at offset 0xabf670) and 'virtual_eisa_release'

AFAIK a PCI to EISA bridge isn't anything hotpluggable, so
pci_eisa_init() can become __init.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I've been seeing some odd NTP behavior recently on a few boxes and
finally narrowed it down to time_offset overflowing when converted to
SHIFT_UPDATE units (which was a side effect from my HZfreeNTP patch).

This patch converts time_offset from a long to a s64 which resolves the
issue.

[tglx@linutronix.de: signedness fixes]
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch uses MAX_REG_NR consistently to refer to the register file size.
 FRAME_SIZE isn't sufficient because on x86_64, it is smaller than the
ptrace register file size.  MAX_REG_NR was introduced as a consistent way
to get the number of registers, but wasn't used everywhere it should be.

When this causes a problem, it makes PTRACE_SETREGS fail on x86_64 because
of a corrupted segment register value in the known-good register file.  The
patch also adds a register dump at that point in case there are any future
problems here.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During a static link, ld has started putting a .note section in the
.uml.setup.init section.  This has the result that the UML setups begin
with 32 bytes of garbage and UML crashes immediately on boot.

This patch creates a specific .note section for ld to drop this stuff
into.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_register_master from .text between 'spi_bitbang_start' (at offset 0x84e11a) and 'bitbang_work'
  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_alloc_master from .text between 'butterfly_attach' (at offset 0x84e681) and 'at25_remove'
  WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_new_device from .text between 'butterfly_attach' (at offset 0x84e7e4) and 'at25_remove'
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When CONFIG_UTS_NS=n, clone(CLONE_NEWUTS) quietly refuses.  So correctly does
not unshare a new uts namespace, but also does not return -EINVAL.

Fix this to return -EINVAL so the caller knows his request was denied.
Signed-off-by: NSerge E. Hallyn <serue@us.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Its now used.. because we added the new definitions so enabled all the
goodies on i386
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

UML/x86_64 needs the same packing of struct epoll_event as x86_64.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

isar_bh() bh handler calls another (compatible) bh handler - BChannel_bh()
- but passes struct BCState* instead of struct work_struct*, which seems
wrong.

Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On Bob's machine clocksource is selecting PIT over the ACPI PM timer,
because he has the PIIX4 bug.  That bug drops the ACPI PM timers rating
to the same as the PIT, so that's why you're getting the PIT.

Realistically, the PIT is much slower then even the triple read ACPI PM,
so the de-ranking code is probably dropping it too far.

So don't drop ACPI PM quite so low if we see the PIIX4 bug.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Bob Tracy <rct@gherkin.frus.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit d720bc4b partially removed a
private implementation of baud speed decoding.  However it doesn't seem
to be complete: after the speed is decoded, it is still being used as an
index to a local speed table (array overrun, no doubt).

This was found by Graham Murray who noticed it caused a 2.6.19 regression
with the SX driver: https://bugs.gentoo.org/170554Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

...  still not sure why we need this ....
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If this mddev and queue got reused for another array that doesn't register a
congested_fn, this function would get called incorretly.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

All that is missing the the function pointers in raid4_pers.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This cancel_delayed_work call is called from a function that is only called
from a piece of code that immediate follows a cancel and destruction of the
workqueue, so it's clearly a mistake.

Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The reused clientid here is a more of a problem for the client than the
server, and the client can report the problem itself if it's serious.
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A regression introduced in the last set of acl patches removed the
INHERIT_ONLY flag from aces derived from the posix acl.  Fix.
Signed-off-by: N"J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

->readdir passes lofft_t offsets (used as nfs cookies) to
nfs3svc_encode_entry{,_plus}, but when they pass it on to encode_entry it
becomes an 'off_t', which isn't good.

So filesystems that returned 64bit offsets would lose.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ingo reported it on lkml in the thread
  "2.6.21-rc5: maxcpus=1 crash in cpufreq: kernel BUG at drivers/cpufreq/cpufreq.c:82!"

This check added to remove_dev  is symmetric to one in add_dev and handles
callbacks for offline cpus cleanly.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

failed VM entry on VMX might still change %fs or %gs, thus make sure
that KVM always reloads the segment selectors. This is crutial on both
x86 and x86_64: x86 has __KERNEL_PDA in %fs on which things like
'current' depends and x86_64 has 0 there and needs MSR_GS_BASE to work.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Intel virtualization extensions do not support virtualizing real mode.  So
kvm uses virtualized vm86 mode to run real mode code.  Unfortunately, this
virtualized vm86 mode does not support the so called "big real" mode, where
the segment selector and base do not agree with each other according to the
real mode rules (base == selector << 4).

To work around this, kvm checks whether a selector/base pair violates the
virtualized vm86 rules, and if so, forces it into conformance.  On a
transition back to protected mode, if we see that the guest did not touch
a forced segment, we restore it back to the original protected mode value.

This pile of hacks breaks down if the gdt has changed in real mode, as it
can cause a segment selector to point to a system descriptor instead of a
normal data segment.  In fact, this happens with the Windows bootloader
and the qemu acpi bios, where a protected mode memcpy routine issues an
innocent 'pop %es' and traps on an attempt to load a system descriptor.

"Fix" by checking if the to-be-restored selector points at a system segment,
and if so, coercing it into a normal data segment.  The long term solution,
of course, is to abandon vm86 mode and use emulation for big real mode.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

After freeing a block there should be no reference to this block.
Signed-off-by: NThomas Viehweger <Thomas.Viehweger@marconi.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Olaf Hering pointed out that SAA7146_CLIPPING_MEM would become
very large for PAGE_SIZE > 4K.
In fact, the number of clipping windows is limited to 16,
and calculate_clipping_registers_rect() does not use more
than 256 bytes. SAA7146_CLIPPING_MEM adjusted accordingly.

Thanks-to: Olaf Hering <olaf@aepfle.de>
Acked-by: NMichael Hunold <hunold@linuxtv.org>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Returning -1 causes the probe to stop, but it should just continue
instead.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>