These devices have accelerometers. To report accelerometer coordinates, a new
property, INPUT_PROP_ACCELEROMETER, is added.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Some Cintiq and Intuos tablets report In Range event. This event is sent before
valid data is reported when tool enters proximity; or before out of proximity
event is reported when tool exits.

While entering proximity, In Range means a pen is detected. This information
can be used for palm/touch rejection on both pen and touch enabled devices.
While exiting, it means the tool has reached its maximum detectable distance.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Bamboo Pads are using the generic processing but their report descriptors
differ from the ISDv* line. The pen fields are marked with the .physical
as Digitizer_Pen, which makes also sense.

Add this field to the checks and enable for free Bamboo Pads.
Reported-by: NJosep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

We introduced nice macros in wacom_wac.c to check whether a field is
a pen or a touch one.

wacom_usage_mapping() still uses it's own tests, which are not in sync with
the wacom_wac tests (.application is not checked).

That means that some legitimate fields might be filtered out from the
usage mapping, and thus will not be used properly while receiving the
events.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The existing generic touch code only reports events after reading an
entire HID report, which practically means that only data about the last
contact in a report will ever be provided to userspace. This patch uses
a trick from hid-multitouch.c to discover what type of field is at the
end of each contact; when such a field is encountered all the stored
contact data will be reported.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

PAD can be on pen interface (Intuos Pro and Cintiq series) or touch
interface (Bamboo PT and Intuos PT series) or its own interface
(Bamboo pen-only and Intuos Pen M/S). We need to mark it independently.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

ISDv4 and v5 are plain HID devices. We can directly implement a generic
HID parsing/handling and remove the need to manually add those PID in
the list of supported devices.

This patch implements the pen support only. The finger part will come in
a later patch.

To be properly notified of an .event() and a .report(), we need to force
hid-core to go through the HID parsing. By default, wacom.ko binds only
hidraw, so the hid parsing is not done by hid-core. When a true HID device
is there, we add the flag HID_CLAIMED_DRIVER to hid->claimed which will
force hid-core to parse the incoming reports.
(Note that this can be easily backported by directly setting the .claimed
flag to HID_CLAIMED_DRIVER even if hid-core does not support
HID_CONNECT_DRIVER)
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

If the input can be created earlier during probe, we can already populate
them while reading the report descriptor. This way, we can rely on the
hid subsystem directly for tablets which already provide a meaningful
report descriptor (like ISDv4-5).

This patch only splits the allocation and registration, but do not
change where we allocate the input. This will come in a later patch.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

A good point of this change is that now, the Intuos4 bluetooth can handle
the different tools (artpen, airbrush, mice), and we get a common interface
between USB and BT for accessing the LEDs/OLEDs.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Tested-by: NPrzemo Firszt <przemo@firszt.eu>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

First, merge the Graphire BT tablet.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Tested-by: NPrzemo Firszt <przemo@firszt.eu>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Now that wacom is a hid driver, there is no point in having a separate
driver for bluetooth devices. This patch prepares the common paths of
Bluetooth devices in the common wacom driver. It also adds the sysfs file
"speed" used by Bluetooth devices.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Tested-by: NPrzemo Firszt <przemo@firszt.eu>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This is used by HID Bluetooth devices but also add some more information
to the USB Wireless Receiver.
We are just porting the bits from hid-wacom.c to the common driver here.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NPrzemo Firszt <przemo@firszt.eu>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The current implementation uses "wacom_battery" as a generic name for
batteries. This prevents us to have two Wacom devices with a battery
attached as the power system will complain about the name which is already
registered.

Use an incremental name for each battery attached.

Related bug:
https://sourceforge.net/p/linuxwacom/bugs/248/Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NPrzemo Firszt <przemo@firszt.eu>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

- Reports the current status of the battery (discharging, charging, full).
- Also notify the upower daemon when there is a change in the battery
  value.
- keep the battery value as a percentage, not the raw value
- add WACOM_QUIRK_BATTERY to easily add a battery to a device (required
  for Bluetooth devices)
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NPrzemo Firszt <przemo@firszt.eu>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

wacom.ko is now a full HID driver, we have to move it into the proper
subdirectory: drivers/hid.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

pktlen is now overwritten by the driver directly by reading the hid
report descriptor. There is no need to declare it statically.
We also move down the position of the field in the struct so that
we can keep the current declaration of Wacom devices.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

HID already parses the report descriptor, so use it instead of implementing
our own.  The special case for Bamboo PT 3rd gen is also removed and
handled in the same way Intuos 5 is treated, by hardcoding it in the
driver.  Last, the unit_exponent stored into the hid field already is
signed, so there is no need to handle a two's complement anymore.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

All USB Wacom tablets are actually HID devices.
For historical reasons, they are handled as plain USB devices.
The current code makes more and more reference to the HID subsystem
like implementing its own HID report descriptor parser to handle new
devices.

From the user point of view, we can transparently switch from this state
to a driver handled in the HID subsystem and clean up a lot of USB specific
code in the wacom.ko driver.

The other benefit once the USB dependecies have been removed is that we can
use a tool like uhid to make regression tests and allow further cleanup or
new implementations without risking breaking current behaviors.

To match the current handling of devices in wacom_wac.c, we rely on the
hid_type set by usbhid. usbhid sets the hid_type to HID_TYPE_USBMOUSE when
it sees a USB boot mouse protocol declared and HID_TYPE_USBNONE when the
device is plain HID. There is thus a one to one matching between the list
of supported devices before and after the switch from USB to HID.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Currently, the pad events are sent through the stylus input device
for the Intuos/Cintiqs, and through the touch input device for the
Bamboos.

To differentiate the buttons pressed on the pad from the ones pressed
on the stylus, the Intuos/Cintiq uses MISC_SERIAL and ABS_MISC. This
lead to a multiplexing of the events into one device, which are then
splitted out in xf86-input-wacom. Bamboos are not using MISC events
because the pad is attached to the touch interface, and only BTN_TOUCH
is used for the finger (and DOUBLE_TAP, etc...). However, the user space
driver still splits out the pad from the touch interface in the same
way it does for the pro line devices.

The other problem we can see with this fact is that some of the Intuos
and Cintiq have a wheel, and the effective range of the reported values
is [0..71]. Unfortunately, the airbrush stylus also sends wheel events
(there is a small wheel on it), but in the range [0..1023]. From the user
space point of view it is kind of difficult to understand that because
the wheel on the pad are quite common, while the airbrush tool is not.

A solution to fix all of these problems is to split out the pad device
from the stylus/touch. This decision makes more sense because the pad is
not linked to the absolute position of the finger or pen, and usually, the
events from the pad are filtered out by the compositor, which then convert
them into actions or keyboard shortcuts.

For backward compatibility with current xf86-input-wacom, the pad devices
still present the ABS_X, ABS_Y and ABS_MISC events, but they can be
completely ignored in the new implementation.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

New Cintiq tablets have a 200 tablet counts outside of screen area.
Add x/y_min for ABS_X/Y to pass this information to userland.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds support for the 0x4004, 0x5000, and 0x5002 sensors found
on what should be the Motion R12, Fujitsu Q704, and Fujitsu T904. These
tablets use a new report ID (3) for their touch packets and a slightly
different HID descriptor format, but are otherwise largely identical in
protocol to the "MTTPC" tablets.

Note:
 * The R12 uses its 0x4004 sensor for touch input only. A pen interface
   is not present in its HID descriptor, though its possible a 0x4004
   may be used for pen input by other tablet PCs in the future.

 * The 0x5002 sensor appears to use a new report ID (8) for its pen
   packets. The other sensors continue to use the traditional report
   ID (2).
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The Win8 version of the Panasonic CF-H2 includes a new Wacom device.
The pen interface appears to use the same protocol as before, but the
touch interface has been tweaked to send Win8-compatible reports.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

New Intuos series models added a hardware switch to turn touch
data on/off. The state of the switch is reported periodically
from the tablet. To report the state the driver will emit SW_MUTE_DEVICE
events.

Reviewed_by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: NPeter Hutterer <peter.hutterer@who-t.net>
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Two tablets in this series support both pen and touch. One (Intuos S)
only supports pen. This patch also updates the driver to process wireless
devices that do not support touch interface.
Tested-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Some multi-interface devices support expresskeys on a separate interface,
such as Bamboo; some multi-interface devices do not support touch at all,
such as Pen only Intuos5. Make sure we report the right device names.
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Acked-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Adds support for the sensors integrated in to the Cintiq Companion
Hybrid. These sensors use by-and-large the same protocol as the
Cintiq 24HD touch.

NOTE: The ExpressKeys on the Cintiq Companion Hybrid are wired to
both the EMR controller and CPU GPIO pins. It may be necessary to
disable their functionality in this driver if building a custom
Android kernel for this device (lest two events be sent to userspace
for every button press).
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Cintiq 13HD, DTK 2241, and Cintiq 22HDT are supported.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It is a pen with 10 finger touch device.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch brings wacom driver in-sync with input-mt changes
made in release 3.7.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This adds support for the two new multi-touch tablets.
Signed-off-by: NPing Cheng <pinglinux@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Decode multitouch reports from the touch sensor of the Cintiq 24HD
touch.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.

Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.

This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data.  To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

0xed supports pen and one finger touch; 0xef is pen only.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Acked-by: NChris Bagwell <chris@cnpbagwell.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

So we can simplify a few type related if statements
Signed-off-by: NPing Cheng <pingc@wacom.com>
Acked-by: NChris Bagwell <chris@cnpbagwell.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Main part of patch is adding support for a new Wacom MT touch
packet and labels these devices using MTSCREEN type.

Other items of interest:

Delete some duplicate code in HID parsing for Y info since
its already done in X path.

In wacom_query_tablet_data(), only invoke the set report
that requests tablets to send Wacom Touch packets for
Finger interfaces.  Mostly, this is to make code intent clear.
Tested-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NChris Bagwell <chris@cnpbagwell.com>
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>