Unlike x86_64, on x86_32, the mapping from cpu to logical apicid
may vary depending on apic in use.  cpu_2_logical_apicid[] array
is used for this mapping.  Replace it with early percpu variable
x86_cpu_to_logical_apicid to make it better aligned with other
mappings.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: eric.dumazet@gmail.com
Cc: yinghai@kernel.org
Cc: brgerst@gmail.com
Cc: gorcunov@gmail.com
Cc: penberg@kernel.org
Cc: shaohui.zheng@intel.com
Cc: rientjes@google.com
LKML-Reference: <1295789862-25482-5-git-send-email-tj@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Latest atom socs(penwell) does not have hpet timer.

As their local APIC timer is clocked at 400KHZ, and the current
code limit their Initial Counter register to 23 bits, they
cannot sleep more than 1.34 seconds which leads to ~2 spurious
wakeup per second (1 per thread)

These SOCs support 32bit timer so we change the max_delta to at
least 31bits. So we can at least sleep for 300 seconds.

We could not find any previous chip errata where lapic would
only have 23 bit precision As powertop is suggesting to activate
HPET to "sleep longer", this could mean this problem is already
known.

Problem is here since very first implementation of lapic timer
as a clock event e9e2cdb4 [PATCH] clockevents: i386 drivers.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NPierre Tardy <pierre.tardy@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
LKML-Reference: <1294327409-19426-1-git-send-email-pierre.tardy@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Then we can reuse it for Xen later.
Acked-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: NAvi Kivity <avi@redhat.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Replace all uses of current_cpu_data with this_cpu operations on the
per cpu structure cpu_info.  The scala accesses are replaced with the
matching this_cpu ops which results in smaller and more efficient
code.

In the long run, it might be a good idea to remove cpu_data() macro
too and use per_cpu macro directly.

tj: updated description

Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NChristoph Lameter <cl@linux.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

We should use MAX_LOCAL_APIC for max apic ids and MAX_APICS as number
of local apics.

Also apic_version[] array should use MAX_LOCAL_APICs.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD464.2020408@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Interrupt-remapping gets enabled very early in the boot, as it determines the
apic mode that the processor can use. And the current code enables the vt-d
fault handling before the setup_local_APIC(). And hence the APIC LDR registers
and data structure in the memory may not be initialized. So the vt-d fault
handling in logical xapic/x2apic modes were broken.

Fix this by enabling the vt-d fault handling in the end_local_APIC_setup()

A cleaner fix of enabling fault handling while enabling intr-remapping
will be addressed for v2.6.38. [ Enabling intr-remapping determines the
usage of x2apic mode and the apic mode determines the fault-handling
configuration. ]
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <20101201062244.541996375@intel.com>
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org [v2.6.32+]
Acked-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

setup_local_APIC() is used to setup local APIC early during CPU
initialization and already assumes that preemption is disabled on
entry. However, The function unnecessarily disables and enables
preemption and uses smp_processor_id() multiple times in and out of
the nested preemption disabled section. This gives the wrong
impression that the function might be able to handle being called with
preemption enabled and/or migrated to another processor in the middle.

Make it clear that the function is always called with preemption
disabled, drop the confusing preemption disable block and call
smp_processor_id() once at the beginning of the function.
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NCyrill Gorcunov <gorcunov@gmail.com>
Reviewed-by: NPekka Enberg <penberg@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: brgerst@gmail.com
LKML-Reference: <4D00B3B9.7060702@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

If x2apic is preenabled and used by the kernel, we don't need to map
the lapic address. That mapping will never be used.

So just skip that in register_lapic_address()
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF69C.9070501@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Remove the printk as well, we don't want to print when nothing
changed. We print in register_lapic_address() already.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF68A.7020902@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

It is almost the same as smp_register_lapic_addr(). We just need to
let smp_read_mpc() call smp_register_lapic_addr() when early==1.

Add the apic_printk to smp_register_lapic_address()
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4CFDF681.3030509@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

They are the same, move the common function to apic.c to allow
further cleanups.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4CFDF675.4060305@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Now that the bulk of the old nmi_watchdog is gone, remove all
the stub variables and hooks associated with it.

This touches lots of files mainly because of how the io_apic
nmi_watchdog was implemented.  Now that the io_apic nmi_watchdog
is forever gone, remove all its fingers.

Most of this code was not being exercised by virtue of
nmi_watchdog != NMI_IO_APIC, so there shouldn't be anything to
risky here.
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Cc: fweisbec@gmail.com
Cc: gorcunov@openvz.org
LKML-Reference: <1289578944-28564-3-git-send-email-dzickus@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Remove the second <asm/atomic.h> inclusion.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
LKML-Reference: <alpine.LNX.2.00.1011072253360.26247@swampdragon.chaosbits.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This improves error messages in case the BIOS was setting up
wrong LVT offsets.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Acked-by: NBorislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1288015419-29543-6-git-send-email-robert.richter@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Some embedded x86 platforms don't setup the APIC in the
BIOS/bootloader and would be forced to add "lapic" on the kernel
command line. That's a bit akward.

Split out the force enable code from detect_init_APIC() and allow
platform code to call it from the platform setup. That avoids the
command line parameter and possible replication of the MSR dance in
the force enable code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
LKML-Reference: <1287510389-8388-1-git-send-email-dirk.brandewie@gmail.com>
Signed-off-by: NDirk Brandewie <dirk.j.brandewie@intel.com>

We want the BIOS to setup the EILVT APIC registers. The offsets
were hardcoded and BIOS settings were overwritten by the OS.
Now, the subsystems for MCE threshold and IBS determine the LVT
offset from the registers the BIOS has setup. If the BIOS setup
is buggy on a family 10h system, a workaround enables IBS. If
the OS determines an invalid register setup, a "[Firmware Bug]:
" error message is reported.

We need this change also for upcomming cpu families.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
LKML-Reference: <1286360874-1471-3-git-send-email-robert.richter@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch implements checks for the availability of LVT entries
(APIC500-530) and reserves it if used. The check becomes
necessary since we want to let the BIOS provide the LVT offsets.
 The offsets should be determined by the subsystems using it
like those for MCE threshold or IBS.  On K8 only offset 0
(APIC500) and MCE interrupts are supported. Beginning with
family 10h at least 4 offsets are available.

Since offsets must be consistent for all cores, we keep track of
the LVT offsets in software and reserve the offset for the same
vector also to be used on other cores. An offset is freed by
setting the entry to APIC_EILVT_MASKED.

If the BIOS is right, there should be no conflicts. Otherwise a
"[Firmware Bug]: ..." error message is generated. However, if
software does not properly determines the offsets, it is not
necessarily a BIOS bug.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
LKML-Reference: <1286360874-1471-2-git-send-email-robert.richter@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Move enable_IR_x2apic() inside the default_setup_apic_routing(),
and for SMP platforms, move the default_setup_apic_routing() after
smp_sanity_check(). This cleans up the code that tries to avoid multiple
calls to default_setup_apic_routing() when smp_sanity_check() fails (which
goes through the APIC_init_uniprocessor() path).
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100827181049.173087246@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

This fixes a regression in 2.6.35 from 2.6.34, that is
present for select models of Intel cpus when people are
using an MP table.

The commit cf7500c0
"x86, ioapic: In mpparse use mp_register_ioapic" started
calling mp_register_ioapic from MP_ioapic_info.  An extremely
simple change that was obviously correct.  Unfortunately
mp_register_ioapic did just a little more than the previous
hand crafted code and so we gained this call path.

The problem call path is:
MP_ioapic_info()
  mp_register_ioapic()
   io_apic_unique_id()
     io_apic_get_unique_id()
       get_physical_broadcast()
         modern_apic()
           lapic_get_version()
             apic_read(APIC_LVR)

Which turned out to be a problem because the local apic
was not mapped, at that point, unlike the similar point
in the ACPI parsing code.

This problem is fixed by mapping the local apic when
parsing the mptable as soon as we reasonably can.

Looking at the number of places we setup the fixmap for
the local apic, I see some serious simplification opportunities.
For the moment except for not duplicating the setting up of the
fixmap in init_apic_mappings, I have not acted on them.

The regression from 2.6.34 is tracked in bug
https://bugzilla.kernel.org/show_bug.cgi?id=16173

Cc: <stable@kernel.org> 2.6.35
Reported-by: NDavid Hill <hilld@binarystorm.net>
Reported-by: NTvrtko Ursulin <tvrtko.ursulin@sophos.com>
Tested-by: NTvrtko Ursulin <tvrtko.ursulin@sophos.com>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <m1eiee86jg.fsf_-_@fess.ebiederm.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Found one x2apic system kexec loop test failed
when CONFIG_NMI_WATCHDOG=y (old) or CONFIG_LOCKUP_DETECTOR=y (current tip)

first kernel can kexec second kernel, but second kernel can not kexec third one.

it can be duplicated on another system with BIOS preenabled x2apic.
First kernel can not kexec second kernel.

It turns out, when kernel boot with pre-enabled x2apic, it will not execute
disable_local_APIC on shutdown path.

when init_apic_mappings() is called in setup_arch, it will skip setting of
apic_phys when x2apic_mode is set. ( x2apic_mode is much early check_x2apic())
Then later, disable_local_APIC() will bail out early because !apic_phys.

So check !x2apic_mode in x2apic_mode in disable_local_APIC with !apic_phys.

another solution could be updating init_apic_mappings() to set apic_phys even
for preenabled x2apic system. Actually even for x2apic system, that lapic
address is mapped already in early stage.

BTW: is there any x2apic preenabled system with apicid of boot cpu > 255?
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3EB22B.3000701@kernel.org>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: stable@kernel.org
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When the SMP kernel decides to crash_kexec() the local APICs may have
pending interrupts in their vector tables.

The setup routine for the local APIC has a deficient mechanism for
clearing these interrupts, it only handles interrupts that has already
been dispatched to the local core for servicing (the ISR register) safely,
it doesn't consider lower prioritized queued interrupts stored in the IRR
register.

If you have more than one pending interrupt within the same 32 bit word in
the LAPIC vector table registers you may find yourself entering the IO
APIC setup with pending interrupts left in the LAPIC.  This is a situation
for wich the IO APIC setup is not prepared.  Depending of what/which
interrupt vector/vectors are stuck in the APIC tables your system may show
various degrees of malfunctioning.  That was the reason why the
check_timer() failed in our system, the timer interrupts was blocked by
pending interrupts from the old kernel when routed trough the IO APIC.

Additional comment from Jiri Bohac:
==============
If this should go into stable release,
I'd add some kind of limit on the number of iterations, just to be safe from
hard to debug lock-ups:

+if (loops++  > MAX_LOOPS) {
+        printk("LAPIC pending clean-up")
+        break;
+}
 while (queued);

with MAX_LOOPS something like 1E9 this would leave plenty of time for the
pending IRQs to be cleared and would and still cause at most a second of delay
if the loop were to lock-up for whatever reason.

[trenn@suse.de:

V2: Use tsc if avail to bail out after 1 sec due to possible virtual
    apic_read calls which may take rather long (suggested by: Avi Kivity
    <avi@redhat.com>) If no tsc is available bail out quickly after
    cpu_khz, if we broke out too early and still have irqs pending (which
    should never happen?) we still get a WARN_ON...

V3: - Fixed indentation -> checkpatch clean
    - max_loops must be signed

V4: - Fix typo, mixed up tsc and ntsc in first rdtscll() call

V5: Adjust WARN_ON() condition to also catch error in cpu_has_tsc case]

Cc: <jbohac@novell.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Kerstin Jonsson <kerstin.jonsson@ericsson.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NThomas Renninger <trenn@suse.de>
LKML-Reference: <201005241913.o4OJDGWM010865@imap1.linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Jan Grossmann reported kernel boot panic while booting SMP
kernel on his system with a single core cpu. SMP kernels call
enable_IR_x2apic() from native_smp_prepare_cpus() and on
platforms where the kernel doesn't find SMP configuration we
ended up again calling enable_IR_x2apic() from the
APIC_init_uniprocessor() call in the smp_sanity_check(). Thus
leading to kernel panic.

Don't call enable_IR_x2apic() and default_setup_apic_routing()
from APIC_init_uniprocessor() in CONFIG_SMP case.

NOTE: this kind of non-idempotent and assymetric initialization
sequence is rather fragile and unclean, we'll clean that up
in v2.6.35. This is the minimal fix for v2.6.34.

Reported-by: Jan.Grossmann@kielnet.net
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: <jbarnes@virtuousgeek.org>
Cc: <david.woodhouse@intel.com>
Cc: <weidong.han@intel.com>
Cc: <youquan.song@intel.com>
Cc: <Jan.Grossmann@kielnet.net>
Cc: <stable@kernel.org> # [v2.6.32.x, v2.6.33.x]
LKML-Reference: <1270083887.7835.78.camel@sbs-t61.sc.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch replaces legacy PIC-related global variable and functions
with the new legacy_pic abstraction.
Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80D04@orsmsx508.amr.corp.intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

We need to fall back from logical-flat APIC mode to physical-flat mode
when we have more than 8 CPUs.  However, in the presence of CPU
hotplug(with bios listing not enabled but possible cpus as disabled cpus in
MADT), we have to consider the number of possible CPUs rather than
the number of current CPUs; otherwise we may cross the 8-CPU boundary
when CPUs are added later.

32bit apic code can use more cleanups (like the removal of vendor checks in
32bit default_setup_apic_routing()) and more unifications with 64bit code.
Yinghai has some patches in works already. This patch addresses the boot issue
that is reported in the virtualization guest context.

[ hpa: incorporated function annotation feedback from Yinghai Lu ]
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1265767304.2833.19.camel@sbs-t61.sc.intel.com>
Acked-by: NShaohui Zheng <shaohui.zheng@intel.com>
Reviewed-by: NYinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: x86@kernel.org
LKML-Reference: <1265478443-31072-10-git-send-email-elendil@planet.nl>
[ Left out the KVM bits. ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

We can use logical flat mode if there are <= 8 logical cpu's
(irrespective of physical apic id values).  This will enable simplified
and efficient IPI and device interrupt routing on such platforms.

This has been tested to work on both Intel and AMD platforms.
Exceptions like IBM summit platform which can't use logical flat mode
are addressed by using OEM platform checks.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Chris McDermott <lcm@linux.vnet.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Revert commit 2fbd07a5, as this commit
breaks an IBM platform with quad-core Xeon cpu's.

According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).

Revert this for now because of the IBM platform breakage.

Another version will be re-submitted after the complete analysis.
Signed-off-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Print only once that the system is supporting x2apic mode.
Signed-off-by: NMike Travis <travis@sgi.com>
Acked-by: NCyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <4B226E92.5080904@sgi.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Suresh made dmar_table_init() already have that protection.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B07A739.3030104@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

clockevents.mult became u32. Fix the printk format.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Commit a98f8fd2 (x86: apic reset
counter on shutdown) set the counter to max to avoid spurious
interrupts when the timer is re-enabled.

(In theory) you'll still get a spurious interrupt if spending
more than 344 seconds with this interrupt disabled and then
unmasking it.

The right thing to do is to clear the register. This disables
the interrupt from happening (at least it does on AMD hardware).
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20091027100138.GB30802@alberich.amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

As only apic noop is used we allow to use almost any operation
caller wants (and which of them noop driver supports of
course).

Initially it was reported by Ingo Molnar that apic noop
issue a warning for pkg id (which is actually false positive
and should be eliminated).

So we save checking (and warning issue) for read/write
operations while allow any other ops to be freely used.

Also:
 - fix noop_cpu_to_logical_apicid, it should be 0.
 - rename noop_default_phys_pkg_id to noop_phys_pkg_id
   (we use default_ prefix for more general routines
    in apic subsystem).
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
LKML-Reference: <20091015150416.GC5331@lenovo>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

In case if apic were disabled we may use the whole apic NOOP driver
instead of sparse poking the some functions in apic driver.

Also NOOP would catch any inappropriate apic operation calls (not
just read/write).
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
Cc: macro@linux-mips.org
LKML-Reference: <20091013201022.747817361@openvz.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Bye-bye Performance Counters, welcome Performance Events!

In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.

Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.

All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)

The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.

Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.

User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)

This patch has been generated via the following script:

  FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')

  sed -i \
    -e 's/PERF_EVENT_/PERF_RECORD_/g' \
    -e 's/PERF_COUNTER/PERF_EVENT/g' \
    -e 's/perf_counter/perf_event/g' \
    -e 's/nb_counters/nb_events/g' \
    -e 's/swcounter/swevent/g' \
    -e 's/tpcounter_event/tp_event/g' \
    $FILES

  for N in $(find . -name perf_counter.[ch]); do
    M=$(echo $N | sed 's/perf_counter/perf_event/g')
    mv $N $M
  done

  FILES=$(find . -name perf_event.*)

  sed -i \
    -e 's/COUNTER_MASK/REG_MASK/g' \
    -e 's/COUNTER/EVENT/g' \
    -e 's/\<event\>/event_id/g' \
    -e 's/counter/event/g' \
    -e 's/Counter/Event/g' \
    $FILES

... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.

Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.

( NOTE: 'counters' are still the proper terminology when we deal
  with hardware registers - and these sed scripts are a bit
  over-eager in renaming them. I've undone some of that, but
  in case there's something left where 'counter' would be
  better than 'event' we can undo that on an individual basis
  instead of touching an otherwise nicely automated patch. )
Suggested-by: NStephane Eranian <eranian@google.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NPaul Mackerras <paulus@samba.org>
Reviewed-by: NArjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

In case of discrete (pretty old) apics we may have cpu_has_apic bit
not set but have to check if smp_found_config (MP spec) is there
and apic was not disabled.

Also don't forget to print apic/io-apic for such case as well.
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090915071230.GA10604@lenovo>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

On Intel platforms, we can use logical flat mode if there are <= 8
logical cpu's (irrespective of physical apic id values). This will
enable simplified and efficient IPI and device interrupt routing on
such platforms.

Fix the relevant comments while we are at it.

We can clean up default_setup_apic_routing() by using apic->probe()
but that is a different item.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: "yinghai@kernel.org" <yinghai@kernel.org>
LKML-Reference: <1253327399.3948.747.camel@sbs-t61.sc.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This was done using Coccinelle's BUG_ON semantic patch.
Signed-off-by: NDaniel Walker <dwalker@fifo99.com>
Cc: Julia Lawall <julia@diku.dk>
LKML-Reference: <1252777220-30796-1-git-send-email-dwalker@fifo99.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

paravirt overrides the setup of the default apic timers as per cpu
timers. Moorestown needs to override that as well.

Move it to x86_init_ops setup and create a separate x86_cpuinit struct
which holds the function for the secondary evtl. hotplugabble CPUs.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

As far as I see there is no external poking of mp_lapic_addr in
this procedure which could lead to unpredited changes and
require local storage unit for it. Lets use it plain forward.
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090826171324.GC4548@lenovo>
Signed-off-by: NIngo Molnar <mingo@elte.hu>