提交 a8fcf1a2 编写于 作者: A Andi Kleen 提交者: Andi Kleen

[PATCH] Remove obsolete PIC mode

PIC mode is an outdated way to drive the APICs that was used on
some early MP boards. It is not supported in the ACPI model.

It is unlikely to be ever configured by any x86-64 system

Remove it thus.
Signed-off-by: NAndi Kleen <ak@suse.de>
上级 e5099134
......@@ -136,72 +136,40 @@ void clear_local_APIC(void)
apic_read(APIC_ESR);
}
void __init connect_bsp_APIC(void)
{
if (pic_mode) {
/*
* Do not trust the local APIC being empty at bootup.
*/
clear_local_APIC();
/*
* PIC mode, enable APIC mode in the IMCR, i.e.
* connect BSP's local APIC to INT and NMI lines.
*/
apic_printk(APIC_VERBOSE, "leaving PIC mode, enabling APIC mode.\n");
outb(0x70, 0x22);
outb(0x01, 0x23);
}
}
void disconnect_bsp_APIC(int virt_wire_setup)
{
if (pic_mode) {
/*
* Put the board back into PIC mode (has an effect
* only on certain older boards). Note that APIC
* interrupts, including IPIs, won't work beyond
* this point! The only exception are INIT IPIs.
*/
apic_printk(APIC_QUIET, "disabling APIC mode, entering PIC mode.\n");
outb(0x70, 0x22);
outb(0x00, 0x23);
}
else {
/* Go back to Virtual Wire compatibility mode */
unsigned long value;
/* For the spurious interrupt use vector F, and enable it */
value = apic_read(APIC_SPIV);
value &= ~APIC_VECTOR_MASK;
value |= APIC_SPIV_APIC_ENABLED;
value |= 0xf;
apic_write(APIC_SPIV, value);
if (!virt_wire_setup) {
/* For LVT0 make it edge triggered, active high, external and enabled */
value = apic_read(APIC_LVT0);
value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED );
value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
apic_write(APIC_LVT0, value);
}
else {
/* Disable LVT0 */
apic_write(APIC_LVT0, APIC_LVT_MASKED);
}
/* Go back to Virtual Wire compatibility mode */
unsigned long value;
/* For LVT1 make it edge triggered, active high, nmi and enabled */
value = apic_read(APIC_LVT1);
value &= ~(
APIC_MODE_MASK | APIC_SEND_PENDING |
/* For the spurious interrupt use vector F, and enable it */
value = apic_read(APIC_SPIV);
value &= ~APIC_VECTOR_MASK;
value |= APIC_SPIV_APIC_ENABLED;
value |= 0xf;
apic_write(APIC_SPIV, value);
if (!virt_wire_setup) {
/* For LVT0 make it edge triggered, active high, external and enabled */
value = apic_read(APIC_LVT0);
value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED );
value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
apic_write(APIC_LVT1, value);
value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
apic_write(APIC_LVT0, value);
} else {
/* Disable LVT0 */
apic_write(APIC_LVT0, APIC_LVT_MASKED);
}
/* For LVT1 make it edge triggered, active high, nmi and enabled */
value = apic_read(APIC_LVT1);
value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
apic_write(APIC_LVT1, value);
}
void disable_local_APIC(void)
......@@ -418,7 +386,7 @@ void __cpuinit setup_local_APIC (void)
* TODO: set up through-local-APIC from through-I/O-APIC? --macro
*/
value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
if (!smp_processor_id() && (pic_mode || !value)) {
if (!smp_processor_id() && !value) {
value = APIC_DM_EXTINT;
apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n", smp_processor_id());
} else {
......@@ -1096,8 +1064,6 @@ int __init APIC_init_uniprocessor (void)
verify_local_APIC();
connect_bsp_APIC();
phys_cpu_present_map = physid_mask_of_physid(boot_cpu_id);
apic_write(APIC_ID, SET_APIC_ID(boot_cpu_id));
......
......@@ -56,7 +56,6 @@ struct mpc_config_intsrc mp_irqs[MAX_IRQ_SOURCES];
int mp_irq_entries;
int nr_ioapics;
int pic_mode;
unsigned long mp_lapic_addr = 0;
......@@ -514,13 +513,6 @@ void __init get_smp_config (void)
printk(KERN_INFO "Using ACPI for processor (LAPIC) configuration information\n");
printk("Intel MultiProcessor Specification v1.%d\n", mpf->mpf_specification);
if (mpf->mpf_feature2 & (1<<7)) {
printk(KERN_INFO " IMCR and PIC compatibility mode.\n");
pic_mode = 1;
} else {
printk(KERN_INFO " Virtual Wire compatibility mode.\n");
pic_mode = 0;
}
/*
* Now see if we need to read further.
......
......@@ -1090,7 +1090,6 @@ void __init smp_prepare_cpus(unsigned int max_cpus)
/*
* Switch from PIC to APIC mode.
*/
connect_bsp_APIC();
setup_local_APIC();
if (GET_APIC_ID(apic_read(APIC_ID)) != boot_cpu_id) {
......
......@@ -178,7 +178,6 @@ extern int mp_irq_entries;
extern struct mpc_config_intsrc mp_irqs [MAX_IRQ_SOURCES];
extern int mpc_default_type;
extern unsigned long mp_lapic_addr;
extern int pic_mode;
#ifdef CONFIG_ACPI
extern void mp_register_lapic (u8 id, u8 enabled);
......
......@@ -33,7 +33,6 @@ extern cpumask_t cpu_initialized;
extern void smp_alloc_memory(void);
extern volatile unsigned long smp_invalidate_needed;
extern int pic_mode;
extern void lock_ipi_call_lock(void);
extern void unlock_ipi_call_lock(void);
extern int smp_num_siblings;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册