提交 a821ebe5 编写于 作者: G Guo-Fu Tseng 提交者: David S. Miller

jme: Added half-duplex mode and IPv6 RSS fix

1. Set bit 5 of GPREG1 to 1 to enable hardware workaround for half-duplex
   mode. Which the MAC processor generates CRS/COL by itself instead of
   receive it from PHY processor.

2. Set bit 6 of GPREG1 to 1 to enable hardware workaround that masks the
   MAC processor working right while calculating IPv6 RSS in 10/100
   mode.

3. Group the workaround codes all together.
Signed-off-by: NGuo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 0ce2f03b
......@@ -190,7 +190,7 @@ jme_reset_mac_processor(struct jme_adapter *jme)
else
gpreg0 = GPREG0_DEFAULT;
jwrite32(jme, JME_GPREG0, gpreg0);
jwrite32(jme, JME_GPREG1, 0);
jwrite32(jme, JME_GPREG1, GPREG1_DEFAULT);
}
static inline void
......@@ -365,7 +365,7 @@ static int
jme_check_link(struct net_device *netdev, int testonly)
{
struct jme_adapter *jme = netdev_priv(netdev);
u32 phylink, ghc, cnt = JME_SPDRSV_TIMEOUT, bmcr;
u32 phylink, ghc, cnt = JME_SPDRSV_TIMEOUT, bmcr, gpreg1;
char linkmsg[64];
int rc = 0;
......@@ -437,37 +437,22 @@ jme_check_link(struct net_device *netdev, int testonly)
case PHY_LINK_SPEED_10M:
ghc |= GHC_SPEED_10M;
strcat(linkmsg, "10 Mbps, ");
if (is_buggy250(jme->pdev->device, jme->chiprev))
jme_set_phyfifoa(jme);
break;
case PHY_LINK_SPEED_100M:
ghc |= GHC_SPEED_100M;
strcat(linkmsg, "100 Mbps, ");
if (is_buggy250(jme->pdev->device, jme->chiprev))
jme_set_phyfifob(jme);
break;
case PHY_LINK_SPEED_1000M:
ghc |= GHC_SPEED_1000M;
strcat(linkmsg, "1000 Mbps, ");
if (is_buggy250(jme->pdev->device, jme->chiprev))
jme_set_phyfifoa(jme);
break;
default:
break;
}
ghc |= (phylink & PHY_LINK_DUPLEX) ? GHC_DPX : 0;
strcat(linkmsg, (phylink & PHY_LINK_DUPLEX) ?
"Full-Duplex, " :
"Half-Duplex, ");
if (phylink & PHY_LINK_MDI_STAT)
strcat(linkmsg, "MDI-X");
else
strcat(linkmsg, "MDI");
if (phylink & PHY_LINK_DUPLEX) {
jwrite32(jme, JME_TXMCS, TXMCS_DEFAULT);
ghc |= GHC_DPX;
} else {
jwrite32(jme, JME_TXMCS, TXMCS_DEFAULT |
TXMCS_BACKOFF |
......@@ -478,6 +463,36 @@ jme_check_link(struct net_device *netdev, int testonly)
TXTRHD_TXREN |
((8 << TXTRHD_TXRL_SHIFT) & TXTRHD_TXRL));
}
strcat(linkmsg, (phylink & PHY_LINK_DUPLEX) ?
"Full-Duplex, " :
"Half-Duplex, ");
if (phylink & PHY_LINK_MDI_STAT)
strcat(linkmsg, "MDI-X");
else
strcat(linkmsg, "MDI");
gpreg1 = GPREG1_DEFAULT;
if (is_buggy250(jme->pdev->device, jme->chiprev)) {
if (!(phylink & PHY_LINK_DUPLEX))
gpreg1 |= GPREG1_HALFMODEPATCH;
switch (phylink & PHY_LINK_SPEED_MASK) {
case PHY_LINK_SPEED_10M:
jme_set_phyfifoa(jme);
gpreg1 |= GPREG1_RSSPATCH;
break;
case PHY_LINK_SPEED_100M:
jme_set_phyfifob(jme);
gpreg1 |= GPREG1_RSSPATCH;
break;
case PHY_LINK_SPEED_1000M:
jme_set_phyfifoa(jme);
break;
default:
break;
}
}
jwrite32(jme, JME_GPREG1, gpreg1);
jme->reg_ghc = ghc;
jwrite32(jme, JME_GHC, ghc);
......
......@@ -963,6 +963,36 @@ enum jme_gpreg0_vals {
GPREG0_PHYADDR_1,
};
/*
* General Purpose REG-1
* Note: All theses bits defined here are for
* Chip mode revision 0x11 only
*/
enum jme_gpreg1_masks {
GPREG1_INTRDELAYUNIT = 0x00000018,
GPREG1_INTRDELAYENABLE = 0x00000007,
};
enum jme_gpreg1_vals {
GPREG1_RSSPATCH = 0x00000040,
GPREG1_HALFMODEPATCH = 0x00000020,
GPREG1_INTDLYUNIT_16NS = 0x00000000,
GPREG1_INTDLYUNIT_256NS = 0x00000008,
GPREG1_INTDLYUNIT_1US = 0x00000010,
GPREG1_INTDLYUNIT_16US = 0x00000018,
GPREG1_INTDLYEN_1U = 0x00000001,
GPREG1_INTDLYEN_2U = 0x00000002,
GPREG1_INTDLYEN_3U = 0x00000003,
GPREG1_INTDLYEN_4U = 0x00000004,
GPREG1_INTDLYEN_5U = 0x00000005,
GPREG1_INTDLYEN_6U = 0x00000006,
GPREG1_INTDLYEN_7U = 0x00000007,
GPREG1_DEFAULT = 0x00000000,
};
/*
* Interrupt Status Bits
*/
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册