提交 23af6039 编写于 作者: P Pierre Ossman

mmc: remove multiwrite capability

Relax requirements on host controllers and only require that they do not
report a transfer count than is larger than the actual one (i.e. a lower
value is okay). This is how many other parts of the kernel behaves so
upper layers should already be prepared to handle that scenario. This
gives us a performance boost on MMC cards.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
上级 97067d55
......@@ -237,17 +237,6 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req)
if (brq.data.blocks > card->host->max_blk_count)
brq.data.blocks = card->host->max_blk_count;
/*
* If the host doesn't support multiple block writes, force
* block writes to single block. SD cards are excepted from
* this rule as they support querying the number of
* successfully written sectors.
*/
if (rq_data_dir(req) != READ &&
!(card->host->caps & MMC_CAP_MULTIWRITE) &&
!mmc_card_sd(card))
brq.data.blocks = 1;
if (brq.data.blocks > 1) {
/* SPI multiblock writes terminate using a special
* token, not a STOP_TRANSMISSION request.
......@@ -367,30 +356,32 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req)
* mark the known good sectors as ok.
*
* If the card is not SD, we can still ok written sectors
* if the controller can do proper error reporting.
* as reported by the controller (which might be less than
* the real number of written sectors, but never more).
*
* For reads we just fail the entire chunk as that should
* be safe in all cases.
*/
if (rq_data_dir(req) != READ && mmc_card_sd(card)) {
u32 blocks;
unsigned int bytes;
blocks = mmc_sd_num_wr_blocks(card);
if (blocks != (u32)-1) {
if (card->csd.write_partial)
bytes = blocks << md->block_bits;
else
bytes = blocks << 9;
if (rq_data_dir(req) != READ) {
if (mmc_card_sd(card)) {
u32 blocks;
unsigned int bytes;
blocks = mmc_sd_num_wr_blocks(card);
if (blocks != (u32)-1) {
if (card->csd.write_partial)
bytes = blocks << md->block_bits;
else
bytes = blocks << 9;
spin_lock_irq(&md->lock);
ret = __blk_end_request(req, 0, bytes);
spin_unlock_irq(&md->lock);
}
} else {
spin_lock_irq(&md->lock);
ret = __blk_end_request(req, 0, bytes);
ret = __blk_end_request(req, 0, brq.data.bytes_xfered);
spin_unlock_irq(&md->lock);
}
} else if (rq_data_dir(req) != READ &&
(card->host->caps & MMC_CAP_MULTIWRITE)) {
spin_lock_irq(&md->lock);
ret = __blk_end_request(req, 0, brq.data.bytes_xfered);
spin_unlock_irq(&md->lock);
}
mmc_release_host(card->host);
......
......@@ -995,7 +995,7 @@ static int __init at91_mci_probe(struct platform_device *pdev)
mmc->f_min = 375000;
mmc->f_max = 25000000;
mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
mmc->caps = MMC_CAP_MULTIWRITE | MMC_CAP_SDIO_IRQ;
mmc->caps = MMC_CAP_SDIO_IRQ;
mmc->max_blk_size = 4095;
mmc->max_blk_count = mmc->max_req_size;
......
......@@ -849,7 +849,7 @@ static int __init atmci_probe(struct platform_device *pdev)
mmc->f_min = (host->bus_hz + 511) / 512;
mmc->f_max = host->bus_hz / 2;
mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE;
mmc->caps |= MMC_CAP_4_BIT_DATA;
mmc->max_hw_segs = 64;
mmc->max_phys_segs = 64;
......
......@@ -1252,10 +1252,7 @@ static int mmc_spi_probe(struct spi_device *spi)
mmc->ops = &mmc_spi_ops;
mmc->max_blk_size = MMC_SPI_BLOCKSIZE;
/* As long as we keep track of the number of successfully
* transmitted blocks, we're good for multiwrite.
*/
mmc->caps = MMC_CAP_SPI | MMC_CAP_MULTIWRITE;
mmc->caps = MMC_CAP_SPI;
/* SPI doesn't need the lowspeed device identification thing for
* MMC or SD cards, since it never comes up in open drain mode.
......
......@@ -535,7 +535,6 @@ static int mmci_probe(struct amba_device *dev, void *id)
mmc->f_min = (host->mclk + 511) / 512;
mmc->f_max = min(host->mclk, fmax);
mmc->ocr_avail = plat->ocr_mask;
mmc->caps = MMC_CAP_MULTIWRITE;
/*
* We can do SGIO
......
......@@ -1317,7 +1317,7 @@ static int __init mmc_omap_new_slot(struct mmc_omap_host *host, int id)
host->slots[id] = slot;
mmc->caps = MMC_CAP_MULTIWRITE;
mmc->caps = 0;
if (host->pdata->conf.wire4)
mmc->caps |= MMC_CAP_4_BIT_DATA;
......
......@@ -973,7 +973,7 @@ static int tifm_sd_probe(struct tifm_dev *sock)
mmc->ops = &tifm_sd_ops;
mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE;
mmc->caps = MMC_CAP_4_BIT_DATA;
mmc->f_min = 20000000 / 60;
mmc->f_max = 24000000;
......
......@@ -1219,7 +1219,7 @@ static int __devinit wbsd_alloc_mmc(struct device *dev)
mmc->f_min = 375000;
mmc->f_max = 24000000;
mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE;
mmc->caps = MMC_CAP_4_BIT_DATA;
spin_lock_init(&host->lock);
......
......@@ -111,12 +111,11 @@ struct mmc_host {
unsigned long caps; /* Host capabilities */
#define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */
#define MMC_CAP_MULTIWRITE (1 << 1) /* Can accurately report bytes sent to card on error */
#define MMC_CAP_MMC_HIGHSPEED (1 << 2) /* Can do MMC high-speed timing */
#define MMC_CAP_SD_HIGHSPEED (1 << 3) /* Can do SD high-speed timing */
#define MMC_CAP_SDIO_IRQ (1 << 4) /* Can signal pending SDIO IRQs */
#define MMC_CAP_SPI (1 << 5) /* Talks only SPI protocols */
#define MMC_CAP_NEEDS_POLL (1 << 6) /* Needs polling for card-detection */
#define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */
#define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */
#define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */
#define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */
#define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */
/* host specific block data */
unsigned int max_seg_size; /* see blk_queue_max_segment_size */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册