This patch removes the various function pointer
assignments and unifies them in a single ops structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Finally, merge these structures and have a single
HW specific data structure.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split the core header files into manageable pieces.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix AR9285 specific noise floor reads and initialize tx and rx
chainmask during reset. This along with the following earlier
patches of ath9k fixes an issue with association noticed in
noisy environment.

ath9k: Fix typo in chip version check
ath9k: Remove unnecessary gpio configuration in ath9k_hw_reset()
ath9k: Fix bug in NF calibration
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The number of chainmasks for AR9285 weren't being
setup when running NF calibration.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that cfg80211 has its own regulatory infrastructure we can
condense ath9k's regulatory code considerably. We only keep data
we need to provide our own regulatory_hint(), reg_notifier() and
information necessary for calibration.

Atheros hardware supports 12 world regulatory domains, since these
are custom we apply them through the the new wiphy_apply_custom_regulatory().
Although we have 12 we can consolidate these into 5 structures based on
frequency and apply a different set of flags that differentiate them on
a case by case basis through the reg_notifier().

If CRDA is not found our own custom world regulatory domain is applied,
this is identical to cfg80211's except we enable passive scan on most
frequencies.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The NOISE_FLOOR array we have is mode specific, and the only
possible indexed values are A, B and G. The mode routine only
can return G or A, so this is band specific. Then since the
values for A and G (5ghz or 2ghz) are the same (-96) we simply
remove the array and use a static value.

If we later determine we want to use special values for
HT configurations we can use the new mac80211 conf_is_ht*()
helpers.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_iscal_supported() just needs to be aware of your band
and if HT20 is being used so lets abandon our internal channel,
HT appended values and internal mode values and use ieee80211_conf
which already carries this information. This works as calibration
is being done for the currently configured channel.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Lets make the request to get the current noise floor threshold
from the EEPROM band specific as it is band specific, not mode
specific.

This also adds a backpointer on the private channel structure
back to the ieee80211_channel structure as this is now needed during
ath9k_hw_getnf().
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove all the useless __func__ prefixes in debug messages,
and replace the DPRINTF macro with a function.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes incorrect noise floor threshold values.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split hw.c into more manageable files:
   ani.c
   calib.c
   eeprom.c
   mac.c
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>