Fix the following compile error on UML.

  arch/um/os-Linux/time.c: In function 'deliver_alarm':
  arch/um/os-Linux/time.c:117:3: error: too few arguments to function 'alarm_handler'
  arch/um/os-Linux/internal.h:1:6: note: declared here

The error was introduced by commit d3c1cfcd ("um: pass siginfo to guest
process") in 3.6-rc1.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
CC: Martin Pärtel <martin.partel@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

patch_instruction() can be called very early on ppc32, when the kernel
isn't yet running at it's linked address. That can cause the !
is_kernel_addr() test in __put_user() to trip and call might_sleep()
which is very bad at that point during boot.

Use a lower level function instead for now, at least until we get to
rework ppc32 boot process to do the code patching later, like ppc64
does.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We have been observing hangs, both of KVM guest vcpu tasks and more
generally, where a process that is woken doesn't properly wake up and
continue to run, but instead sticks in TASK_WAKING state.  This
happens because the update of rq->wake_list in ttwu_queue_remote()
is not ordered with the update of ipi_message in
smp_muxed_ipi_message_pass(), and the reading of rq->wake_list in
scheduler_ipi() is not ordered with the reading of ipi_message in
smp_ipi_demux().  Thus it is possible for the IPI receiver not to see
the updated rq->wake_list and therefore conclude that there is nothing
for it to do.

In order to make sure that anything done before smp_send_reschedule()
is ordered before anything done in the resulting call to scheduler_ipi(),
this adds barriers in smp_muxed_message_pass() and smp_ipi_demux().
The barrier in smp_muxed_message_pass() is a full barrier to ensure that
there is a full ordering between the smp_send_reschedule() caller and
scheduler_ipi().  In smp_ipi_demux(), we use xchg() rather than
xchg_local() because xchg() includes release and acquire barriers.
Using xchg() rather than xchg_local() makes sense given that
ipi_message is not just accessed locally.

This moves the barrier between setting the message and calling the
cause_ipi() function into the individual cause_ipi implementations.
Most of them -- those that used outb, out_8 or similar -- already had
a full barrier because out_8 etc. include a sync before the MMIO
store.  This adds an explicit barrier in the two remaining cases.

These changes made no measurable difference to the speed of IPIs as
measured using a simple ping-pong latency test across two CPUs on
different cores of a POWER7 machine.

The analysis of the reason why processes were not waking up properly
is due to Milton Miller.

Cc: stable@vger.kernel.org # v3.0+
Reported-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

During a context switch we always restore the per thread DSCR value.
If we aren't doing explicit DSCR management
(ie thread.dscr_inherit == 0) and the default DSCR changed while
the process has been sleeping we end up with the wrong value.

Check thread.dscr_inherit and select the default DSCR or per thread
DSCR as required.

This was found with the following test case, when running with
more threads than CPUs (ie forcing context switching):

http://ozlabs.org/~anton/junkcode/dscr_default_test.c

With the four patches applied I can run a combination of all
test cases successfully at the same time:

http://ozlabs.org/~anton/junkcode/dscr_default_test.c
http://ozlabs.org/~anton/junkcode/dscr_explicit_test.c
http://ozlabs.org/~anton/junkcode/dscr_inherit_test.cSigned-off-by: NAnton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If the default DSCR is non zero we set thread.dscr_inherit in
copy_thread() meaning the new thread and all its children will ignore
future updates to the default DSCR. This is not intended and is
a change in behaviour that a number of our users have hit.

We just need to inherit thread.dscr and thread.dscr_inherit from
the parent which ends up being much simpler.

This was found with the following test case:

http://ozlabs.org/~anton/junkcode/dscr_default_test.cSigned-off-by: NAnton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When we update the DSCR either via emulation of mtspr(DSCR) or via
a change to dscr_default in sysfs we don't update thread.dscr.
We will eventually update it at context switch time but there is
a period where thread.dscr is incorrect.

If we fork at this point we will copy the old value of thread.dscr
into the child. To avoid this, always keep thread.dscr in sync with
reality.

This issue was found with the following testcase:

http://ozlabs.org/~anton/junkcode/dscr_inherit_test.cSigned-off-by: NAnton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Writing to dscr_default in sysfs doesn't actually change the DSCR -
we rely on a context switch on each CPU to do the work. There is no
guarantee we will get a context switch in a reasonable amount of time
so fire off an IPI to force an immediate change.

This issue was found with the following test case:

http://ozlabs.org/~anton/junkcode/dscr_explicit_test.cSigned-off-by: NAnton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The CPU hotplug code for the powernv platform currently only puts
offline CPUs into nap mode if the powersave_nap variable is set.
However, HV-style KVM on this platform requires secondary CPU threads
to be offline and in nap mode.  Since we know nap mode works just
fine on all POWER7 machines, and the only machines that support the
powernv platform are POWER7 machines, this changes the code to
always put offline CPUs into nap mode, regardless of powersave_nap.
Powersave_nap still controls whether or not CPUs go into nap mode
when idle, as before.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

At the moment the handler for hypervisor decrementer interrupts is
the same as for decrementer interrupts, i.e. timer_interrupt().
This is bogus; if we ever do get a hypervisor decrementer interrupt
it won't have anything to do with the next timer event.  In fact
the only time we get hypervisor decrementer interrupts is when one
is left pending on exit from a KVM guest.

When we get a hypervisor decrementer interrupt we don't need to do
anything special to clear it, since they are edge-triggered on the
transition of HDEC from 0 to -1.  Thus this adds an empty handler
function for them.  We don't need to have them masked when interrupts
are soft-disabled, so we use STD_EXCEPTION_HV instead of
MASKABLE_EXCEPTION_HV.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

arch_update_cpu_topology() should only return 1 when the topology has
actually changed, and should return 0 otherwise.

This patch fixes a potential bug where rebuild_sched_domains() would
reinitialize the sched domains even when the topology hasn't changed.
Signed-off-by: NJesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Test-compiling obscure machines I notice that the gemini (which
by the way lacks a defconfig) is broken since some time back.
Adding a simple missing include makes it build again.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

armadillo800eva default boot loader is "hermit",
and it's tag->u.core.flags has flag when kernel boots.
Because of this, ${LINUX}/arch/arm/kernel/setup.c :: parse_tag_core()
didn't remove MS_RDONLY flag from root_mountflags.
Thus, the rootfs is mounted as "readonly".
This patch adds "rw" kernel parameter,
and enable read/write mounts for rootfs

Cc: Masahiro Nakai <nakai@atmark-techno.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

Linux-next has failed to compile for kirkwood since 23 August with:

arch/arm/mach-kirkwood/db88f6281-bp-setup.c:29: error: 'SZ_1M' undeclared here (not in a function)
arch/arm/mach-kirkwood/db88f6281-bp-setup.c:33: error: 'SZ_4M' undeclared here (not in a function)

Add missing <linux/sizes.h>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

renesas_usbhs driver can play role as both Host and Gadget.
In case of Gadget, it requires not only renesas_usbhs
but also usb gadget module (like g_ether).
So, renesas_usbhs driver calls usb_add_gadget_udc() on probe time.

Because of this behavior,
Host port plays also Gadget role if kernel has both Host/Gadget support.

In mackerel case, from 0ada2da5
(ARM: mach-shmobile: mackerel: use renesas_usbhs instead of r8a66597_hcd)
usb0 plays Gadget role, and usb1 plays Host role,
and current mackerel board probes as usb1 -> usb0.
Thus, 1st installed usb gadget module (like g_ether) will be
assigned to usb1 (= usb Host port), and 2nd module to usb0 (= usb Gadget port).
It is very confusable for user.
This patch fixup usb modes probing order as usb0 -> usb1.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

Since armadillo800eva has 2 sound cards,
and had reversed deferred probe order issue,
it was purposely registered in reverse order.

But it was solved by
1d29cfa5
(driver core: fixup reversed deferred probe order)

armadillo800eva board is expecting that
FSI-WM8978 is the 1st, and FSI-HDMI is the 2nd sound card.
This patch fixes it up
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

dummy_supplies for smsc911x are registered as "smsc911x".
smsc911x driver needs id = -1
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

Fix this compile error:

arch/s390/kernel/machine_kexec.c: In function ‘setup_regs’:
arch/s390/kernel/machine_kexec.c:63:3: error: implicit declaration
 of function ‘smp_store_status’ [-Werror=implicit-function-declaration]
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

KVM_GET_MSR was missing support for PV EOI,
which is needed for migration.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

The GPIO buttons are named SW3, SW4, SW5 and SW6 on the board
silkscreen. Update the buttons descriptions accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>

This reverts commit b1acf1bb.

Something went horribly wrong when I did savedefconfig, not sure what,
but what's in there is busted so let's revert it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For certain speculative events on Power7, 'perf stat' reports far higher
event count than 'perf record' for the same event.

As described in following commit, a performance monitor exception is raised
even when the the performance events are rolled back.

        commit 0837e324
        Author: Anton Blanchard <anton@samba.org>
        Date:   Wed Mar 9 14:38:42 2011 +1100

perf_event_interrupt() records an event only when an overflow occurs. But
this check for overflow is a simple 'if (val < 0)'.

Because the events are rolled back, this check for overflow fails and the
event is not recorded. perf_event_interrupt() later uses pmc_overflow() to
detect the overflow and resets the counters and the events are lost completely.

To properly detect the overflow of rolled back events, use pmc_overflow()
even when recording events.

To reproduce:
        $ cat strcpy.c
        #include <stdio.h>
        #include <string.h>
        main()
        {
                char buf[256];

                alarm(5);
                while(1)
                        strcpy(buf, "string1");
        }

        $ perf record -e r20014 ./strcpy
        $ perf report -n > report.1
        $ perf stat -e r20014 > report.2
        # Compare report.1 and report.2
Reported-by: NMaynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The enhanced prefetch hint patches corrupt the condition register
that was used to check if we are in interrupt. Fix this by using cr1.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

"powerpc: Use enhanced touch instructions in POWER7
copy_to_user/copy_from_user" was applied twice. Remove one.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.

Directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes

Use personality() macro to compare only PER_MASK bytes and make sure that
we are setting only the bits that should be set, instead of overwriting
the whole value.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Checking for device mask to cover the whole IOMMU table is too strict.
IOMMU allocators should handle mask constraint properly for each
allocation.

The patch enables to use old AirPort Extreme cards on PowerMacs with
more than 1GB of memory; without the patch the driver init fails with:

  b43-pci-bridge 0001:01:01.0: Warning: IOMMU window too big for device mask
  b43-pci-bridge 0001:01:01.0: mask: 0x3fffffff, table end: 0x80000000
  b43-phy0 ERROR: The machine/kernel does not support the required 30-bit DMA mask
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For powerpc BooKE and e200, singlestep is handled on the critical/dbg
exception stack. This causes current_thread_info() to fail for kgdb
internal, so previously We work around this issue by copying
the thread_info from the kernel stack before calling kgdb_handle_exception,
and copying it back afterwards.

But actually we don't do this properly. We should backup current_thread_info
then restore that when exit.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to skip a breakpoint exception when it occurs after
a breakpoint has already been removed.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The kgdb_single_step flag has the possibility to indefinitely
hang the system on an SMP system.

The x86 arch have the same problem, and that problem was fixed by
commit 8097551d(kgdb,x86: do not set kgdb_single_step
on x86). This patch does the same behaviors as x86's patch.
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add several #includes that mpic_msgr relies on being pulled implicitly,
which only happens on certain configs.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Meador Inge <meador_inge@mentor.com>
Cc: Jia Hongtao <B38951@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently if you are doing a global perf recording with hardware
breakpoints (ie perf record -e mem:0xdeadbeef -a), you can oops with:

  Faulting instruction address: 0xc000000000738890
  cpu 0xc: Vector: 300 (Data Access) at [c0000003f76af8d0]
      pc: c000000000738890: .hw_breakpoint_handler+0xa0/0x1e0
      lr: c000000000738830: .hw_breakpoint_handler+0x40/0x1e0
      sp: c0000003f76afb50
     msr: 8000000000001032
     dar: 6f0
   dsisr: 42000000
    current = 0xc0000003f765ac00
    paca    = 0xc00000000f262a00   softe: 0        irq_happened: 0x01
    pid   = 6810, comm = loop-read
  enter ? for help
  [c0000003f76afbe0] c00000000073cd04 .notifier_call_chain.isra.0+0x84/0xe0
  [c0000003f76afc80] c00000000073cdbc .notify_die+0x3c/0x60
  [c0000003f76afd20] c0000000000139f0 .do_dabr+0x40/0xf0
  [c0000003f76afe30] c000000000005a9c handle_dabr_fault+0x14/0x48
  --- Exception: 300 (Data Access) at 0000000010000480
  SP (ff8679e0) is in userspace

This is because we don't check to see if the break point is associated
with task before we deference the task_struct pointer.

This changes the update to use current.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are a few whitespace goolies in xmon.c, some of them appear to
be my fault. Fix them all in one go.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Since the printk internals were reworked the xmon 'dl' command which
dumps the content of __log_buf has stopped working.

It is now a structured buffer, so just dumping it doesn't really work.

Use the helpers added for kgdb to print out the content.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Yocto (Built by Poky 7.0) 1.2 root filesystems fail to boot,
at least over nfs, with:

Failed to mount /dev: No such device

Configuring DEVTMPFS fixes it.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

run make savedefconfig on fsl defconfigs.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Using 'select' in Kconfig is hard, a platform cannot just
enable a driver without also making sure that its subsystem
is there. Also, there is no actual code dependency between
the platform and the gpio leds driver.

Without this patch, building without LEDS_CLASS esults in:

drivers/built-in.o: In function `create_gpio_led.part.2':
governor_userspace.c:(.devinit.text+0x5a58): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `gpio_led_remove':
governor_userspace.c:(.devexit.text+0x6b8): undefined reference to `led_classdev_unregister'

This reverts 8733f53c "ARM: ux500: Kconfig: Compile in leds-gpio
support for Snowball" that introduced the regression and did not
provide a helpful explanation.

In order to leave the GPIO LED code still present in normal
builds, this also enables the symbol in u8500_defconfig, in addition
to the other LED drivers that are already selected there.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>

The head-v7.S contains a call to the generic cpu_suspend function,
which is only available when selected by the i.MX6 code. As
pointed out by Shawn Guo, i.MX5 does not actually use any
functions defined in head-v7.S. It is also needed only for
the i.MX6 power management code and for the SMP code, so
we can restrict building this file to situations in which
at least one of those two is present.

Finally, other platforms with a similar file call it headsmp.S,
so we can rename it to the same for consistency.

Without this patch, building imx5 standalone results in:

arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
arch/arm/mach-imx/head-v7.S:104: undefined reference to `cpu_resume'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Eric Miao <eric.miao@linaro.org>
Cc: stable@vger.kernel.org

The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.

Building IMX without CPU_FREQ_TABLE results in:

arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org