The mic detect level registers are used from common code to configure
the button detection code. Add these registers to the defaults list and
mark them as readable for wm5110.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The FLL gains are present on all devices and controlled from common code
shared between them. This patch adds these registers into defaults list
for wm5110 and marks them as readable.
Reported-by: ND.J. Barrow <dbarrow@wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Reg_cache variable is used to lock step enable register
from being accessed and written by both TSC and ADC
at the same time.
However, it isn't updated anywhere in the code at all.

If both TSC and ADC are used, eventually 1FFFF is always
written enabling all 16 steps uselessly causing a mess.

Patch fixes it by correcting the locks and updates the
variable by reading the step enable register
Signed-off-by: NZubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

If we disable DCVDD before we mark the cache as cache only, we might
attempt to write to the chip whilst it is powered down and lose a write.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the build
warnings when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.

drivers/mfd/ab8500-gpadc.c:891:12: warning: 'ab8500_gpadc_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:903:12: warning: 'ab8500_gpadc_resume' defined but not used [-Wunused-function]
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add CONFIG_PM_RUNTIME to runtime_suspend/runtime_resume functions
to fix the build warnings when CONFIG_PM_RUNTIME is not selected.
This is because runtime PM callbacks defined by SET_RUNTIME_PM_OPS
are only used when the CONFIG_PM_RUNTIME is enabled.

drivers/mfd/ab8500-gpadc.c:870:12: warning: 'ab8500_gpadc_runtime_suspend' defined but not used [-Wunused-function]
drivers/mfd/ab8500-gpadc.c:878:12: warning: 'ab8500_gpadc_runtime_resume' defined but not used [-Wunused-function]
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the build
warnings when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.

drivers/mfd/ucb1x00-core.c:672:12: warning: 'ucb1x00_suspend' defined but not used [-Wunused-function]
drivers/mfd/ucb1x00-core.c:704:12: warning: 'ucb1x00_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

'mmc_callback_data' and 'vtg' are pointers.

Fix the following sparse warning:

drivers/mfd/menelaus.c:445:43: warning: Using plain integer as NULL pointer
drivers/mfd/menelaus.c:469:20: warning: Using plain integer as NULL pointer
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

twl4030_power_configure_scripts(), twl4030_power_configure_resources(),
twl4030_power_probe() are used only in this file.

Fix the following sparse warnings:

drivers/mfd/twl4030-power.c:496:5: warning: symbol 'twl4030_power_configure_scripts' was not declared. Should it be static?
drivers/mfd/twl4030-power.c:512:5: warning: symbol 'twl4030_power_configure_resources' was not declared. Should it be static?
drivers/mfd/twl4030-power.c:556:5: warning: symbol 'twl4030_power_probe' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

'lpc_chipset_info' is used only in this file.

Fix the following sparse warning:

drivers/mfd/lpc_ich.c:216:21: warning: symbol 'lpc_chipset_info' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Casting (void *) data of max8997_pmic_dt_match is necessary,
because variable 'data' of struct 'of_device_id' is defined as
'const void *data'. Thus, pointer should be used instead of value.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

It is only called from this file so there is no need for it to be in the
global namespace and cause sparse to warn.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Since the conversion to the regmap API setting bits per word will lead to
data corruption since the regmap API already configures the bits per word
appropriately.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Fixes this compilation error:
  linux/include/linux/mfd/ucb1x00.h:137:17: error: field 'dev' has incomplete type
Signed-off-by: NAndrea Adami <andrea.adami@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Fixes this compilation error:
  linux/include/linux/mfd/mcp.h:22:16: error: field 'attached_device' has incomplete type
  linux/include/linux/mfd/mcp.h:48:23: error: field 'drv' has incomplete type
Signed-off-by: NAndrea Adami <andrea.adami@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

AFE Pen Ctrl and TouchScreen transistors enabling is not
required when only ADC mode is being used, so check for availability of
TSC driver before accessing control register.
Signed-off-by: NPatil, Rachna <rachna@ti.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NZubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

ADC is ideally expected to work at a frequency of 3MHz.
The present code had a check, which returned error if the frequency
went below the threshold  value. But since AM335x supports various
working frequencies, this check is not required.
Now the code just uses the internal ADC clock divider to set the ADC
frequency w.r.t the sys clock.
Signed-off-by: NPatil, Rachna <rachna@ti.com>
Signed-off-by: NZubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since enabling VMID takes a runtime PM reference there is no need to
suppress suspend when doing a runtime suspend. Similarly the digital
inputs and outputs are DAPM widgets and therefore the ASoC core will
be holding a reference for them.

This used to be required when integration with system suspend was being
bodged.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The jack detection code holds runtime PM references when required so
there is no need for suspend to do any checks.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Kconfig prompt for WM8997 says "Support for..." while the other MFD
Kconfigs (including the adjacent ones for other Arizona devices) just
list the device name which sticks out like a sore thumb when doing
configuration.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since these are fixed rate clocks which are registered with common clock
framework so remove these from list of regulators which were unnecessarily
incrementing the count(S2MPS11_REGULATOR_MAX) of regulators.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

During a move to use managed resources, the .remove function all was
deemed superfluous which subsequently led to its deletion. As there are
no remaining users of the stored 'base' address we only have to use it
locally during probe.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The err: label is not needed we can just return instead of the jump there.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

To comply with coding style.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

TWL6040 is used only with OMAP4/5 SoCs and they can only boot in in DT mode.
The support for pdata/legacy boot can be removed.

Add TODO comment to the header file that all pdata struct can be removed in
the next merge window (after the sub driver updates are in).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The performance of regmap-irq is improved if the interrupt mask registers
can be cached since it does read/modify/update cycles so start using the
register cache infrastructure for those registers. We should use this more
widely but I don't have a datasheet and this is a nice, conservative
starting point.
Signed-off-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

DA9055 is a combination of pmic and codec. This patch updates the DA9055 i2c
device id name to match the standard naming convention followed for such chips.
Signed-off-by: NAnkur Raina <Ankur.Raina@kpitcummins.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch clears all the events received while powering up DA9055.

While powering up DA9055, both power sequencer and gpio events are received.
These events remain uncleared after boot up, due to which further event handling
also fails. DA9055 has three event registers. The event register bits are set
to '1' on receiving an event. The events can be cleared on writing a '1' to
the set bit, which would then clear that bit to '0'. After applying this patch
we have a clean state after boot up.
Signed-off-by: NAnkur Raina <Ankur.Raina@kpitcummins.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch adds DT compatible string for s2mps11 and binding documentation.
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add TPS659038 Device Tree documentation.
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control fixes from Linus Walleij:
 - Driver fixes for AM33xx, SIRF and PFC pin controllers
 - Fix a compile warning from the pinctrl single-register driver
 - Fix a little nasty memory leak

* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix a memleak when freeing maps
  pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
  pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
  arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
  pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
  pinctrl: sirf: fix the pin number and mux bit for usp0
  pinctrl: am33xx dt binding: correct include path

Merge tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "Oleg is working on fixing a very tight race between opening a event
  file and deleting that event at the same time (both must be done as
  root).

  I also found a bug while testing Oleg's patches which has to do with a
  race with kprobes using the function tracer.

  There's also a deadlock fix that was introduced with the previous
  fixes"

* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
  ftrace: Add check for NULL regs if ops has SAVE_REGS set
  tracing: Kill trace_cpu struct/members
  tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
  tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
  tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
  tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
  tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
  tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()

Pull SCSI fixes from James Bottomley:
 "This is five bug fixes, two of which fix long standing problems
  causing crashes (sd and mvsas).  The remaining three are hung (isci
  race) or lost (qla2xxx, isci) devices"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] isci: fix breakage caused by >16byte CDB patch
  [SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
  [SCSI] sd: fix crash when UA received on DIF enabled device
  [SCSI] qla2xxx: Properly set the tagging for commands.
  [SCSI] isci: Fix a race condition in the SSP task management path

Pull drm fixes from Dave Airlie:
 "This is just a regular fixes pull apart from the qxl one, it has
  radeon and intel bits in it,

  The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
  regression, whereas radeon is more DPM fixes, a few lockup fixes and
  some rn50/r100 DAC fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/dpm: fix r600_enable_sclk_control()
  drm/radeon/dpm: implement force performance levels for rv6xx
  drm/radeon/dpm: fix displaygap programming on rv6xx
  drm/radeon/dpm: fix a typo in the rv6xx mclk setup
  drm/i915: initialize gt_lock early with other spin locks
  drm/i915: fix hdmi portclock limits
  drm/radeon: fix combios tables on older cards
  drm/radeon: improve dac adjust heuristics for legacy pdac
  drm/radeon: Another card with wrong primary dac adj
  drm/radeon: fix endian issues with DP handling (v3)
  drm/radeon/vm: only align the pt base to 32k
  drm/radeon: wait for 3D idle before using CP DMA

Pull qxl drm fixes from Dave Airlie:
 "Okay as I warned, the qxl driver was running a bit free and loose with
  its ttm object reservations and the new lockdep enabled reservation
  tracking shone a bright light into it, it also with the new
  reservations mutexes hits a possible deadlock during boot.

  The first patch is a real fix to render the console correctly as the
  driver used to just drop irq renderering as too hard, this also fixes
  a sleeping while atomic warning.

  The other two patches are the big ugly ones that redo how the driver
  allocates objects and reserves them and makes things all work
  properly, I've tested this in a VM, and compared to the current code
  which hits a lockdep warning and the sleep while atomic warning before
  failing.

  So sorry this is coming in late, I should have tested qxl before
  merging the mutex code, but I'd rather just fix qxl with this than
  revert the reservations code at this point"

* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
  qxl: convert qxl driver to proper use for reservations
  qxl: allow creation of pre-pinned objects and use for releases.
  drm/qxl: add delayed fb operations

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are just two fixes, a revert of the would-be backlight fix that
  didn't work and an intel_pstate fix for two problems related to
  maximum P-state selection.

  Specifics:

   - Revert of the ACPI video commit that I hoped would help fix
     backlight problems related to Windows 8 compatibility on some
     systems.  Unfortunately, it turned out to cause problems to happen
     too.

   - Fix for two problems in intel_pstate, a possible failure to respond
     to a load change on a quiet system and a possible failure to select
     the highest available P-state on some systems.  From Dirk
     Brandewie"

* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
  cpufreq / intel_pstate: Change to scale off of max P-state

Pull arm64 fixes from Catalin Marinas:
 - Stack size increased to 16K (similar to other 64-bit architectures)
 - Additional cache flushing for secondary CPUs boot mode

* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: Change kernel stack size to 16K
  arm64: Fix definition of arm_pm_restart to match the declaration
  arm64: virt: ensure visibility of __boot_cpu_mode

Pull ARM SoC fixes from Olof Johansson:
 "This is a largeish batch of fixes, mostly because I missed -rc2 due to
  travel/vacation.  So in number these are a bit more than ideal unless
  you amortize them over two -rcs.

  Quick breakdown:
   - Defconfig updates
     - Making multi_v7_defconfig useful on more hardware to encourage
       single-image usage
     - Davinci and nomadik updates due to new code merged this merge
       window
   - Fixes for UART on Samsung platforms, both PM and clock-related
   - A handful of warning fixes from defconfig builds, including for
     max8925 backlight and pxamci (both with appropriate acks)
   - Exynos5440 fixes for LPAE configuration, PM
   - ...plus a bunch of other smaller changes all over the place

  I expect to switch to regressions-or-severe-bugs-only fixes from here
  on out"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
  mfd: max8925: fix dt code for backlight
  ARM: omap5: Only select errata 798181 if SMP
  ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
  ARM: EXYNOS: Fix low level debug support
  ARM: SAMSUNG: Save/restore only selected uart's registers
  ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
  ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
  ARM: multi_v7_defconfig: Select USB chipidea driver
  ARM: pxa: propagate errors from regulator_enable() to pxamci
  ARM: zynq: fix compilation warning
  ARM: keystone: fix compilation warning
  ARM: highbank: Only touch common coherency control register fields
  ARM: footbridge: fix overlapping PCI mappings
  dmaengine: shdma: fix a build failure on platforms with no DMA support
  ARM: STi: Set correct ARM ERRATAs.
  ARM: dts: STi: Fix pinconf setup for STiH416 serial2
  ARM: nomadik: configure for NO_HZ and HRTIMERS
  ARM: nomadik: update defconfig base
  ARM: nomadik: Update MMC defconfigs
  ARM: davinci: defconfig: enable EDMA driver
  ...