- 23 11月, 2012 1 次提交
-
-
由 Sebastian Ott 提交于
Do not use more than one KERN_<level> per printk. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Acked-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 26 9月, 2012 3 次提交
-
-
由 Stefan Haberland 提交于
A common way to prepare a z/VM mini disk is to format the real device with a z/VM tool like CPFMTXA and then define a mini disk that excludes the first cylinder, i.e. the cylinder 0 of the virtual disk is located at cylinder 1 of the real device. The DASD device driver will recognize such a mini disk as formatted, as the uniform record layout on the disk matches that of an LDL formatted device. However, the cylinder value in the 'count' field of the ECKD records matches the geometry of the real device, and not that of the mini disk, so I/O requests will fail with 'record not found' errors. To make the mini disk usable, it needs to be formatted with a tool like dasdfmt. To enable tools like distribution installation tools to recognize this situation, the DASD device driver should report such a mini disk as 'not formatted'. To this end we need to extend the device recognition code to check not just for proper record sizes, but also for proper cylinder/head/record values. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Reviewed-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Change -ENOSYS to -EOPNOTSUPP. Return value is used only internally. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Add the eadm facility bits to the css characteristics and move them to a new header. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 17 9月, 2012 1 次提交
-
-
由 Stefan Haberland 提交于
If a new path is available we need to verify the path data. If it is the first path for a device the stop bits are removed after path verification. If a pathgroup is established we need to set system characteristics for the lcu. Therefore I/O has to be started. If the device is stopped the set system characteristics worker may block the path verification worker and the device is blocked. Turn on failfast for set system characteristics CQR to prevent a deadlock with the path verification worker. If a pathgroup is established on a device that is not in use trigger path verification. Maybe we were not informed about a working path. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Reviewed-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 28 8月, 2012 1 次提交
-
-
由 Heiko Carstens 提交于
For unimplemented ioctls the dasd driver should return -ENOTTY. Reported-by: NWanlong Gao <gaowanlong@cn.fujitsu.com> Acked-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 20 7月, 2012 1 次提交
-
-
由 Heiko Carstens 提交于
Remove the file name from the comment at top of many files. In most cases the file name was wrong anyway, so it's rather pointless. Also unify the IBM copyright statement. We did have a lot of sightly different statements and wanted to change them one after another whenever a file gets touched. However that never happened. Instead people start to take the old/"wrong" statements to use as a template for new files. So unify all of them in one go. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
-
- 16 7月, 2012 1 次提交
-
-
由 Stefan Haberland 提交于
Add a mechanism to wait for outstanding IO during shutdown. Schedule the block_bh and device_bh and wait until our request queues are empty. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
-
- 11 4月, 2012 1 次提交
-
-
由 Julia Lawall 提交于
Extend some error paths to call dasd_sfree_request as done earlier in the function. The error-handling code is also moved to the end of the function. Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 11 3月, 2012 1 次提交
-
-
由 Stefan Haberland 提交于
Calling validate server on devices in offline processing may cause an OOPS in the dasd_sleep_on function. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Reviewed-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 27 2月, 2012 1 次提交
-
-
由 Heiko Carstens 提交于
The new is_compat_task() define for the !COMPAT case in include/linux/compat.h conflicts with a similar define in arch/s390/include/asm/compat.h. This is the minimal patch which fixes the build issues. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 19 1月, 2012 2 次提交
-
-
由 Stefan Haberland 提交于
If a pathgroup is established we get an event and have to revalidate the server to propagate supported features like PAV and enable them. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
Remove the optimization that validate server is only called once per LCU. If a device is set online we only know that we already know the LCU. But if the pathgroup was lost in between we have to do a validate server again to activate some features. Since we have no indication when a pathgroup gets lost we have to do a validate server every time a device is set online. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 27 12月, 2011 2 次提交
-
-
由 Stefan Haberland 提交于
If an IO request is build on an alias device without prefix enabled we try to calculate with zero data from the alias device. This triggers a BUG statement with fixpoint divide exception. This case is very unlikely and can only happen if the pathgroup is lost with an alias device already in use. Prevent the alias device from being used in this case. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
Prevents possible data corruption by detecting cabling error. Therefor read and compare the UID for all available channel paths. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 30 10月, 2011 4 次提交
-
-
由 Martin Schwidefsky 提交于
Fix two NULL pointer warnings in the dasd driver: drivers/s390/block/dasd_eckd.c:2353:20: warning: Using plain integer as NULL pointer drivers/s390/block/dasd_eckd.c:2415:44: warning: Using plain integer as NULL pointer Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
Mark the device as suspended and delay execution of the path verification worker to prevent mix-up. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
The buffer for read configuration data has to be initialized with an EBCDIC string to show support for extended UIDs to z/VM. If this read configuration data CQR needs to be retried, the buffer may have changed in between. So re-initialize the buffer to get a correct extended UID under z/VM. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Peter Oberparleiter 提交于
Current IRQ statistics support does not show detail counts for I/O interrupts which are processed internally only. The result is a summation count which is way off such as this one: CPU0 CPU1 CPU2 I/O: 1331 710 442 [...] QAI: 15 16 16 [I/O] QDIO Adapter Interrupt QDI: 1 0 0 [I/O] QDIO Interrupt DAS: 706 645 381 [I/O] DASD C15: 26 10 0 [I/O] 3215 C70: 0 0 0 [I/O] 3270 TAP: 0 0 0 [I/O] Tape VMR: 0 0 0 [I/O] Unit Record Devices LCS: 0 0 0 [I/O] LCS CLW: 0 0 0 [I/O] CLAW CTC: 0 0 0 [I/O] CTC APB: 0 0 0 [I/O] AP Bus Fix this by moving I/O interrupt accounting into the common I/O layer. Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 03 8月, 2011 1 次提交
-
-
由 Stefan Haberland 提交于
To use raw track access some special storage server commands are needed. Older storage hardware may not support these commands. So check if raw track access is possible while setting the DASD online. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
-
- 23 5月, 2011 2 次提交
-
-
由 Heiko Carstens 提交于
Check return value of itcw_add_dcw() for error code and return it. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Remove trivially unused variables as detected with -Wunused-but-set-variable. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 20 4月, 2011 1 次提交
-
-
由 Stefan Weinhuber 提交于
When evaluating sense data in dasd_eckd_check_for_device_change, we must always check for the type of sense data in byte 27, bit 0, to make sure that the rest of the sense data is interpreted correctly. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 31 3月, 2011 1 次提交
-
-
由 Lucas De Marchi 提交于
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>
-
- 23 3月, 2011 1 次提交
-
-
由 Sebastian Ott 提交于
Remove the owner and name members of struct ccw_driver and convert all drivers to store this data in the embedded struct device_driver. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 16 3月, 2011 1 次提交
-
-
由 Heiko Carstens 提交于
Get rid of this: drivers/s390/block/dasd_eckd.c: In function 'dasd_eckd_build_cp_tpm_track.clone.8': drivers/s390/block/dasd_eckd.c:2589:34: warning: 'len_to_track_end' may be used uninitialized in this function Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 17 2月, 2011 1 次提交
-
-
由 Stefan Haberland 提交于
The 3880 storage control unit supports a 3380 device type, but not a 3390 device type. Reported-by: NStephen Powell <zlinuxman@wowway.com> Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 05 1月, 2011 4 次提交
-
-
由 Stefan Haberland 提交于
Normal I/O operations through the DASD device driver give only access to the data fields of an ECKD device even for track based I/O. This patch extends the DASD device driver to give access to whole ECKD tracks including count, key and data fields. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Weinhuber 提交于
If a DASD device has been reserved by a Linux system, and later this reservation is ‘stolen’ by a second system by means of an unconditional reserve, then the first system receives a notification about this fact. With this patch such an event can be either ignored, as before, or it can be used to let the device fail all I/O request, so that the device will not block anymore. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Weinhuber 提交于
When a new path is added at runtime, the CIO layer will call the drivers path_event callback. The DASD device driver uses this callback to trigger a path verification for the new path. The driver will use only those paths for I/O, which have been successfully verified. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Weinhuber 提交于
Some storage systems support multitrack High Performance FICON requests, which read or write data to more than one track. This patch enables the DASD device driver to generate multitrack High Performance FICON requests. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 29 10月, 2010 1 次提交
-
-
由 Stefan Weinhuber 提交于
The BIODASDSNID ioctl executes a 'Sense Path Group ID' command on a DASD ECKD device. The returned path group data allows user space programs to determine path state and path group ID of the channel paths to the device. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 25 10月, 2010 2 次提交
-
-
由 Stefan Weinhuber 提交于
The dasd interrupt handler needs to distinguish solicited from unsolicited interrupts, as unsolicited interrupts may require special handling (e.g. summary unit checks) and solicited interrupts require proper error recovery for the failed I/O request. The interrupt handler needs to check several bit fields in the interrupt response block (irb) to make this distinction. So far our check of the status control bits has not been specific enough, which may lead to a failed request getting just retried instead of the necessary error recovery. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
The dasd_eckd_dump_sense_dbf function uses a macro for s390 debug feature that can handle up to 8 parameters (for the DASD device driver). Fix the function to use only the maximum number of parameters. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 21 9月, 2010 1 次提交
-
-
由 Nikanth Karthikesan 提交于
Fix various typos of valid. Signed-off-by: NNikanth Karthikesan <knikanth@suse.de> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 10 8月, 2010 2 次提交
-
-
由 Stefan Haberland 提交于
This feature provides a user interface to specify the timeout for missing interrupts for standard I/O operations. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Weinhuber 提交于
The DASD reserve and release ioctls use the preallocated memory pool of the respective device to build their CCW requests. However, when the device is busy, the pool may already be empty and the ioctl fails. Usually this can be recovered by calling the ioctl again, but in a situation in which we need to issue an unconditional reserve to make a device operational again, this would be not recoverable. To avoid a failure due to lack of memory, DASD device driver will preallocate enough memory for a single reserve/release request, which can be used if normal allocation fails. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 27 5月, 2010 1 次提交
-
-
由 Stefan Haberland 提交于
React on unit checks during cio internal I/O. Handle as unsolicited interrupt and advice cio to retry. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
- 17 5月, 2010 2 次提交
-
-
由 Stefan Haberland 提交于
Remove the duplicate of the DASD uid from the devmap structure. Use the uid from the device private structure instead. This also removes a lockdep warning complaining about a possible SOFTIRQ-safe -> SOFTIRQ-unsafe lock order. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
For base Parallel Access Volume (PAV) there is a fixed mapping of base and alias devices. With dynamic PAV this mapping can be changed so that an alias device is used with another base device. This patch enables the DASD device driver to tolerate dynamic PAV changes. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-