Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
	In wrapped commands, we need to verify and convert
	the slave's port into the real physical port.
	Furthermore, when sending the response back to the slave,
	a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
	The slave assumes that sqpn is used for QP1 communication.
	If the slave is assigned to a port != (first port), we need
	to adjust the sqpn that will direct its QP1 packets into the
	correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
	In B0 steering, gid[5] contains the port. It needs
	to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
	When a slave queries the hardware, it needs to view only
	the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
	The QP port is encoded in the sched_qp, thus in modify_qp we need
	to encode the correct port in sched_qp.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a fix to a regression introduced by commit:
"982290a7 net/mlx4_core: Check port number for validity
before accessing data"

IPoIB could not attach to multicast group and we get this in dmesg:
[144214.145008] ib0: failed to attach to multicast group, ret = -22
[144214.145016] ib0: couldn't attach QP to multicast group ff12:401b:ffff:0000:0000:0000:ffff:ffff
[144214.145019] ib0: multicast join failed for ff12:401b:ffff:0000:0000:0000:ffff:ffff, status -22

The cause to the problem is because port is extracted from gid[5].
Which is only valid for Ethernet.
Removed this validation in mlx4_qp_attach_common(), which is accessed
from both Ethernet and IB flows.
Error flow for bad port value in Ethernet is already exists in that
function.
Signed-off-by: NMoni Shoua <monis@mellanox.co.il>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for allocating IB UD QPs that we can steer
traffic from.  We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.

This command isn't supported for VFs.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.

This is done through the following elements:

 - read tunneling device caps in QUERY_DEV_CAP
 - add helper function to do SET_PORT for tunneling
 - add DMFS VXLAN steering rule definitions
 - add CQE and WQE checksum offload field definitions
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f4ec9e95 "mlx4_core: Change bitmap allocator to work in round-robin fashion"
introduced round-robin allocation (via bitmap) for all resources which allocate
via a bitmap.

Round robin allocation is desirable for mcgs, counters, pd's, UARs, and xrcds.
These are simply numbers, with no involvement of ICM memory mapping.

Round robin is required for QPs, since we had a problem with immediate
reuse of a 24-bit QP number (commit f4ec9e95).

However, for other resources which use the bitmap allocator and involve
mapping ICM memory -- MPTs, CQs, SRQs -- round-robin is not desirable.

What happens in these cases is the following:

ICM memory is allocated and mapped in chunks of 256K.

Since the resource allocation index goes up monotonically, the allocator
will eventually require mapping a new chunk. Now, chunks are also unmapped
when their reference count goes back to zero.  Thus, if a single app is
running and starts/exits frequently we will have the following situation:

When the app starts, a new chunk must be allocated and mapped.

When the app exits, the chunk reference count goes back to zero, and the
chunk is unmapped and freed. Therefore, the app must pay the cost of allocation
and mapping of ICM memory each time it runs (although the price is paid only when
allocating the initial entry in the new chunk).

For apps which allocate MPTs/SRQs/CQs and which operate as described above,
this presented a performance problem.

We therefore roll back the round-robin allocator modification for MPTs, CQs, SRQs.
Reported-by: NMatthew Finlay <matt@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.

This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.

In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove code that triggers trivial build warnings.

drivers/net/ethernet/mellanox/mlx4/cmd.c: In function ‘mlx4_set_vf_vlan’:
drivers/net/ethernet/mellanox/mlx4/cmd.c:2256: warning: variable ‘vf_oper’ set but not used
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_mode’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:648: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_id’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:685: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_hw_rule_sz’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:712: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/fw.c: In function ‘mlx4_opreq_action’:
drivers/net/ethernet/mellanox/mlx4/fw.c:1732: warning: variable ‘type_m’ set but not used
drivers/net/ethernet/mellanox/mlx4/srq.c:302: warning: no previous prototype for ‘mlx4_srq_lookup’
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-arrange some of code which fills DMFS HW structures so we can use
it from within the core driver and from the IB driver too, e.g when
verbs DMFS structures are transformed into mlx4 hardware structs.

Also, add struct mlx4_flow_handle struct which will be of use by the
DMFS verbs flow in the IB driver.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Some of struct mlx4_net_trans_rule_hw_ctrl fields were packed into u32
and accessed through bit field operations.  Expose and access them
directly as u8 or u16.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Change struct mlx4_net_trans_rule_hw_eth :: vlan_id name to vlan_tag

Change struct mlx4_net_trans_rule_hw_ib :: r_u_qpn name to l3_qpn

The patch doesn't introduce any functional change or API change
towards the firmware.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Align the names used by enum mlx4_net_trans_promisc_mode with the
actual firmware specification.  The patch doesn't introduce any
functional change or API change towards the firmware.

Remove MLX4_FS_PROMISC_FUNCTION_PORT which isn't of use.  Add new
enums MLX4_FS_{UC/MC}_SNIFFER as a preparation step for sniffer
support.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

A pre-step for supporting guests that use B0 steering over a hypervisor
that runs in DMFS (device managed flow steering mode). Add helper function
which allows to translate L2 attachments / detachments provided in B0 mode
to DMFS rules.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allow_loopback flag was wrongly set using arithmetic bit operation, change
the code to use logical bit operation.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering).  If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: NAviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define this macro is one common place instead of duplicating it over the code
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should be ">=" here instead of ">".  MLX4_NET_TRANS_RULE_NUM is 6.
We use "spec->id" as an array offset into the __rule_hw_sz[] and
__sw_id_hw[] arrays which have 6 elements.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device managed flow steering API has three promiscuous modes:

1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.

Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.

This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.

A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.

B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,

The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle the compiler warnings on variables which are set but not used
by removing the relevant variable or casting a return value which is
ignored on purpose to void.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_multicast_attach/detach() should use always MLX4_MC_STEER flag
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_qp_attach/detach_common() don't use hash variable, move it to find_entry()
static find_entry() in mcg.c doesn't use steer argument
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use port number for correct steering (list per port).
Before the fix all steering entries (for both physical ports)
were managed in first port structures, so we had leakage of resources
for port 2.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use MLX4_DEV_CAP_FLAG_VEP_UC_STEER for unicast_promisc_add/remove
Unicast entries were managed in wrong data structures.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware

Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let multicast/unicast attaching flow go through resource tracker.
The PF is the one responsible for managing all the steering entries.
Define and use module parameter that determines the number of qps
per multicast group.
Minor changes in function calls according to changed prototype.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).

This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.

Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c

This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.

CC: Roland Dreier <roland@kernel.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Query another dword containing up to 32 extended device capabilities
and merge it into struct mlx4_caps.flags.  Update the code that
handles the current extended device capabilities (e.g UDP RSS, WoL,
vep steering, etc) to use the extended device cap flags field instead
of a field per extended capability.  Initial patch done by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

On error path kfree() should get pointer to memory allocated by
kmalloc() not the address of variable holding it (which is on stack).
Signed-off-by: NMariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

In case of allocation failure, tried to use the promiscuous QP
entry that was previously freed.
Now freeing this entry only in case we will not put it back to the list
of promiscuous entries.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>