提交 86415d43 编写于 作者: B Bruno Randolf 提交者: John W. Linville

ath5k: fix I/Q calibration (for real)

I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.

1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.

2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.

3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.

4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Cc: stable@kernel.org
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 a3b980fd
......@@ -1386,38 +1386,39 @@ static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah,
goto done;
/* Calibration has finished, get the results and re-run */
/* work around empty results which can apparently happen on 5212 */
for (i = 0; i <= 10; i++) {
iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR);
i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I);
q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q);
ATH5K_DBG_UNLIMIT(ah->ah_sc, ATH5K_DEBUG_CALIBRATE,
"iq_corr:%x i_pwr:%x q_pwr:%x", iq_corr, i_pwr, q_pwr);
if (i_pwr && q_pwr)
break;
}
i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7;
q_coffd = q_pwr >> 7;
/* No correction */
if (i_coffd == 0 || q_coffd == 0)
/* protect against divide by 0 and loss of sign bits */
if (i_coffd == 0 || q_coffd < 2)
goto done;
i_coff = ((-iq_corr) / i_coffd);
i_coff = (-iq_corr) / i_coffd;
i_coff = clamp(i_coff, -32, 31); /* signed 6 bit */
/* Boundary check */
if (i_coff > 31)
i_coff = 31;
if (i_coff < -32)
i_coff = -32;
q_coff = (i_pwr / q_coffd) - 128;
q_coff = clamp(q_coff, -16, 15); /* signed 5 bit */
q_coff = (((s32)i_pwr / q_coffd) - 128);
ATH5K_DBG_UNLIMIT(ah->ah_sc, ATH5K_DEBUG_CALIBRATE,
"new I:%d Q:%d (i_coffd:%x q_coffd:%x)",
i_coff, q_coff, i_coffd, q_coffd);
/* Boundary check */
if (q_coff > 15)
q_coff = 15;
if (q_coff < -16)
q_coff = -16;
/* Commit new I/Q value */
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE |
((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S));
/* Commit new I/Q values (set enable bit last to match HAL sources) */
AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_Q_I_COFF, i_coff);
AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_Q_Q_COFF, q_coff);
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE);
/* Re-enable calibration -if we don't we'll commit
* the same values again and again */
......
......@@ -2187,6 +2187,7 @@
*/
#define AR5K_PHY_IQ 0x9920 /* Register Address */
#define AR5K_PHY_IQ_CORR_Q_Q_COFF 0x0000001f /* Mask for q correction info */
#define AR5K_PHY_IQ_CORR_Q_Q_COFF_S 0
#define AR5K_PHY_IQ_CORR_Q_I_COFF 0x000007e0 /* Mask for i correction info */
#define AR5K_PHY_IQ_CORR_Q_I_COFF_S 5
#define AR5K_PHY_IQ_CORR_ENABLE 0x00000800 /* Enable i/q correction */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册