提交 6476a907 编写于 作者: K Krzysztof Hałasa

WAN pc300too.c: Fix PC300-X.21 detection

pc300too driver works around a bug in PCI9050 bridge.  Unfortunately
it was doing that too late.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
上级 72364706
......@@ -319,27 +319,6 @@ static int __devinit pc300_pci_init_one(struct pci_dev *pdev,
}
pci_set_drvdata(pdev, card);
if (pdev->device == PCI_DEVICE_ID_PC300_TE_1 ||
pdev->device == PCI_DEVICE_ID_PC300_TE_2)
card->type = PC300_TE; /* not fully supported */
else if (card->init_ctrl_value & PC300_CTYPE_MASK)
card->type = PC300_X21;
else
card->type = PC300_RSV;
if (pdev->device == PCI_DEVICE_ID_PC300_RX_1 ||
pdev->device == PCI_DEVICE_ID_PC300_TE_1)
card->n_ports = 1;
else
card->n_ports = 2;
for (i = 0; i < card->n_ports; i++)
if (!(card->ports[i].netdev = alloc_hdlcdev(&card->ports[i]))) {
printk(KERN_ERR "pc300: unable to allocate memory\n");
pc300_pci_remove_one(pdev);
return -ENOMEM;
}
if (pci_resource_len(pdev, 0) != PC300_PLX_SIZE ||
pci_resource_len(pdev, 2) != PC300_SCA_SIZE ||
pci_resource_len(pdev, 3) < 16384) {
......@@ -348,13 +327,13 @@ static int __devinit pc300_pci_init_one(struct pci_dev *pdev,
return -EFAULT;
}
plxphys = pci_resource_start(pdev,0) & PCI_BASE_ADDRESS_MEM_MASK;
plxphys = pci_resource_start(pdev, 0) & PCI_BASE_ADDRESS_MEM_MASK;
card->plxbase = ioremap(plxphys, PC300_PLX_SIZE);
scaphys = pci_resource_start(pdev,2) & PCI_BASE_ADDRESS_MEM_MASK;
scaphys = pci_resource_start(pdev, 2) & PCI_BASE_ADDRESS_MEM_MASK;
card->scabase = ioremap(scaphys, PC300_SCA_SIZE);
ramphys = pci_resource_start(pdev,3) & PCI_BASE_ADDRESS_MEM_MASK;
ramphys = pci_resource_start(pdev, 3) & PCI_BASE_ADDRESS_MEM_MASK;
card->rambase = pci_ioremap_bar(pdev, 3);
if (card->plxbase == NULL ||
......@@ -369,6 +348,27 @@ static int __devinit pc300_pci_init_one(struct pci_dev *pdev,
card->init_ctrl_value = readl(&((plx9050 __iomem *)card->scabase)->init_ctrl);
pci_write_config_dword(pdev, PCI_BASE_ADDRESS_0, plxphys);
if (pdev->device == PCI_DEVICE_ID_PC300_TE_1 ||
pdev->device == PCI_DEVICE_ID_PC300_TE_2)
card->type = PC300_TE; /* not fully supported */
else if (card->init_ctrl_value & PC300_CTYPE_MASK)
card->type = PC300_X21;
else
card->type = PC300_RSV;
if (pdev->device == PCI_DEVICE_ID_PC300_RX_1 ||
pdev->device == PCI_DEVICE_ID_PC300_TE_1)
card->n_ports = 1;
else
card->n_ports = 2;
for (i = 0; i < card->n_ports; i++)
if (!(card->ports[i].netdev = alloc_hdlcdev(&card->ports[i]))) {
printk(KERN_ERR "pc300: unable to allocate memory\n");
pc300_pci_remove_one(pdev);
return -ENOMEM;
}
/* Reset PLX */
p = &card->plxbase->init_ctrl;
writel(card->init_ctrl_value | 0x40000000, p);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册