提交 254416aa 编写于 作者: J John W. Linville

wireless: report reasonable bitrate for MCS rates through wext

Previously, cfg80211 had reported "0" for MCS (i.e. 802.11n) bitrates
through the wireless extensions interface.  However, nl80211 was
converting MCS rates into a reasonable bitrate number.  This patch moves
the nl80211 code to cfg80211 where it is now shared between both the
nl80211 interface and the wireless extensions interface.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 a252e749
......@@ -378,6 +378,8 @@ int rdev_set_freq(struct cfg80211_registered_device *rdev,
struct wireless_dev *for_wdev,
int freq, enum nl80211_channel_type channel_type);
u16 cfg80211_calculate_bitrate(struct rate_info *rate);
#ifdef CONFIG_CFG80211_DEVELOPER_WARNINGS
#define CFG80211_DEV_WARN_ON(cond) WARN_ON(cond)
#else
......
......@@ -1637,39 +1637,6 @@ static int parse_station_flags(struct genl_info *info,
return 0;
}
static u16 nl80211_calculate_bitrate(struct rate_info *rate)
{
int modulation, streams, bitrate;
if (!(rate->flags & RATE_INFO_FLAGS_MCS))
return rate->legacy;
/* the formula below does only work for MCS values smaller than 32 */
if (rate->mcs >= 32)
return 0;
modulation = rate->mcs & 7;
streams = (rate->mcs >> 3) + 1;
bitrate = (rate->flags & RATE_INFO_FLAGS_40_MHZ_WIDTH) ?
13500000 : 6500000;
if (modulation < 4)
bitrate *= (modulation + 1);
else if (modulation == 4)
bitrate *= (modulation + 2);
else
bitrate *= (modulation + 3);
bitrate *= streams;
if (rate->flags & RATE_INFO_FLAGS_SHORT_GI)
bitrate = (bitrate / 9) * 10;
/* do NOT round down here */
return (bitrate + 50000) / 100000;
}
static int nl80211_send_station(struct sk_buff *msg, u32 pid, u32 seq,
int flags, struct net_device *dev,
u8 *mac_addr, struct station_info *sinfo)
......@@ -1716,8 +1683,8 @@ static int nl80211_send_station(struct sk_buff *msg, u32 pid, u32 seq,
if (!txrate)
goto nla_put_failure;
/* nl80211_calculate_bitrate will return 0 for mcs >= 32 */
bitrate = nl80211_calculate_bitrate(&sinfo->txrate);
/* cfg80211_calculate_bitrate will return 0 for mcs >= 32 */
bitrate = cfg80211_calculate_bitrate(&sinfo->txrate);
if (bitrate > 0)
NLA_PUT_U16(msg, NL80211_RATE_INFO_BITRATE, bitrate);
......
......@@ -720,3 +720,36 @@ int cfg80211_change_iface(struct cfg80211_registered_device *rdev,
return err;
}
u16 cfg80211_calculate_bitrate(struct rate_info *rate)
{
int modulation, streams, bitrate;
if (!(rate->flags & RATE_INFO_FLAGS_MCS))
return rate->legacy;
/* the formula below does only work for MCS values smaller than 32 */
if (rate->mcs >= 32)
return 0;
modulation = rate->mcs & 7;
streams = (rate->mcs >> 3) + 1;
bitrate = (rate->flags & RATE_INFO_FLAGS_40_MHZ_WIDTH) ?
13500000 : 6500000;
if (modulation < 4)
bitrate *= (modulation + 1);
else if (modulation == 4)
bitrate *= (modulation + 2);
else
bitrate *= (modulation + 3);
bitrate *= streams;
if (rate->flags & RATE_INFO_FLAGS_SHORT_GI)
bitrate = (bitrate / 9) * 10;
/* do NOT round down here */
return (bitrate + 50000) / 100000;
}
......@@ -1256,10 +1256,7 @@ int cfg80211_wext_giwrate(struct net_device *dev,
if (!(sinfo.filled & STATION_INFO_TX_BITRATE))
return -EOPNOTSUPP;
rate->value = 0;
if (!(sinfo.txrate.flags & RATE_INFO_FLAGS_MCS))
rate->value = 100000 * sinfo.txrate.legacy;
rate->value = 100000 * cfg80211_calculate_bitrate(&sinfo.txrate);
return 0;
}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册