board-n8x0.c 15.6 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
/*
 * linux/arch/arm/mach-omap2/board-n8x0.c
 *
 * Copyright (C) 2005-2009 Nokia Corporation
 * Author: Juha Yrjola <juha.yrjola@nokia.com>
 *
 * Modified from mach-omap2/board-generic.c
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/stddef.h>
20
#include <linux/i2c.h>
21 22
#include <linux/spi/spi.h>
#include <linux/usb/musb.h>
23
#include <sound/tlv320aic3x.h>
24 25 26 27

#include <asm/mach/arch.h>
#include <asm/mach-types.h>

28 29
#include <plat/board.h>
#include <plat/common.h>
30
#include <plat/menelaus.h>
31
#include <mach/irqs.h>
32 33
#include <plat/mcspi.h>
#include <plat/onenand.h>
34
#include <plat/mmc.h>
35
#include <plat/serial.h>
36

37 38
#include "mux.h"

39 40 41 42
static int slot1_cover_open;
static int slot2_cover_open;
static struct device *mmc_device;

43 44 45 46 47 48
#define TUSB6010_ASYNC_CS	1
#define TUSB6010_SYNC_CS	4
#define TUSB6010_GPIO_INT	58
#define TUSB6010_GPIO_ENABLE	0
#define TUSB6010_DMACHAN	0x3f

49
#ifdef CONFIG_USB_MUSB_TUSB6010
50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108
/*
 * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
 * 1.5 V voltage regulators of PM companion chip. Companion chip will then
 * provide then PGOOD signal to TUSB6010 which will release it from reset.
 */
static int tusb_set_power(int state)
{
	int i, retval = 0;

	if (state) {
		gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
		msleep(1);

		/* Wait until TUSB6010 pulls INT pin down */
		i = 100;
		while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
			msleep(1);
			i--;
		}

		if (!i) {
			printk(KERN_ERR "tusb: powerup failed\n");
			retval = -ENODEV;
		}
	} else {
		gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
		msleep(10);
	}

	return retval;
}

static struct musb_hdrc_config musb_config = {
	.multipoint	= 1,
	.dyn_fifo	= 1,
	.num_eps	= 16,
	.ram_bits	= 12,
};

static struct musb_hdrc_platform_data tusb_data = {
#if defined(CONFIG_USB_MUSB_OTG)
	.mode		= MUSB_OTG,
#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
	.mode		= MUSB_PERIPHERAL,
#else /* defined(CONFIG_USB_MUSB_HOST) */
	.mode		= MUSB_HOST,
#endif
	.set_power	= tusb_set_power,
	.min_power	= 25,	/* x2 = 50 mA drawn from VBUS as peripheral */
	.power		= 100,	/* Max 100 mA VBUS for host mode */
	.config		= &musb_config,
};

static void __init n8x0_usb_init(void)
{
	int ret = 0;
	static char	announce[] __initdata = KERN_INFO "TUSB 6010\n";

	/* PM companion chip power control pin */
I
Igor Grinberg 已提交
109 110
	ret = gpio_request_one(TUSB6010_GPIO_ENABLE, GPIOF_OUT_INIT_LOW,
			       "TUSB6010 enable");
111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134
	if (ret != 0) {
		printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
		       TUSB6010_GPIO_ENABLE);
		return;
	}
	tusb_set_power(0);

	ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
					TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
					TUSB6010_GPIO_INT, TUSB6010_DMACHAN);
	if (ret != 0)
		goto err;

	printk(announce);

	return;

err:
	gpio_free(TUSB6010_GPIO_ENABLE);
}
#else

static void __init n8x0_usb_init(void) {}

135
#endif /*CONFIG_USB_MUSB_TUSB6010 */
136 137


138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184
static struct omap2_mcspi_device_config p54spi_mcspi_config = {
	.turbo_mode	= 0,
	.single_channel = 1,
};

static struct spi_board_info n800_spi_board_info[] __initdata = {
	{
		.modalias	= "p54spi",
		.bus_num	= 2,
		.chip_select	= 0,
		.max_speed_hz   = 48000000,
		.controller_data = &p54spi_mcspi_config,
	},
};

#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)

static struct mtd_partition onenand_partitions[] = {
	{
		.name           = "bootloader",
		.offset         = 0,
		.size           = 0x20000,
		.mask_flags     = MTD_WRITEABLE,	/* Force read-only */
	},
	{
		.name           = "config",
		.offset         = MTDPART_OFS_APPEND,
		.size           = 0x60000,
	},
	{
		.name           = "kernel",
		.offset         = MTDPART_OFS_APPEND,
		.size           = 0x200000,
	},
	{
		.name           = "initfs",
		.offset         = MTDPART_OFS_APPEND,
		.size           = 0x400000,
	},
	{
		.name           = "rootfs",
		.offset         = MTDPART_OFS_APPEND,
		.size           = MTDPART_SIZ_FULL,
	},
};

185 186 187 188 189 190 191 192
static struct omap_onenand_platform_data board_onenand_data[] = {
	{
		.cs		= 0,
		.gpio_irq	= 26,
		.parts		= onenand_partitions,
		.nr_parts	= ARRAY_SIZE(onenand_partitions),
		.flags		= ONENAND_SYNC_READ,
	}
193 194 195
};
#endif

196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211
#if defined(CONFIG_MENELAUS) &&						\
	(defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE))

/*
 * On both N800 and N810, only the first of the two MMC controllers is in use.
 * The two MMC slots are multiplexed via Menelaus companion chip over I2C.
 * On N800, both slots are powered via Menelaus. On N810, only one of the
 * slots is powered via Menelaus. The N810 EMMC is powered via GPIO.
 *
 * VMMC				slot 1 on both N800 and N810
 * VDCDC3_APE and VMCS2_APE	slot 2 on N800
 * GPIO23 and GPIO9		slot 2 EMMC on N810
 *
 */
#define N8X0_SLOT_SWITCH_GPIO	96
#define N810_EMMC_VSD_GPIO	23
212
#define N810_EMMC_VIO_GPIO	9
213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299

static int n8x0_mmc_switch_slot(struct device *dev, int slot)
{
#ifdef CONFIG_MMC_DEBUG
	dev_dbg(dev, "Choose slot %d\n", slot + 1);
#endif
	gpio_set_value(N8X0_SLOT_SWITCH_GPIO, slot);
	return 0;
}

static int n8x0_mmc_set_power_menelaus(struct device *dev, int slot,
					int power_on, int vdd)
{
	int mV;

#ifdef CONFIG_MMC_DEBUG
	dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1,
		power_on ? "on" : "off", vdd);
#endif
	if (slot == 0) {
		if (!power_on)
			return menelaus_set_vmmc(0);
		switch (1 << vdd) {
		case MMC_VDD_33_34:
		case MMC_VDD_32_33:
		case MMC_VDD_31_32:
			mV = 3100;
			break;
		case MMC_VDD_30_31:
			mV = 3000;
			break;
		case MMC_VDD_28_29:
			mV = 2800;
			break;
		case MMC_VDD_165_195:
			mV = 1850;
			break;
		default:
			BUG();
		}
		return menelaus_set_vmmc(mV);
	} else {
		if (!power_on)
			return menelaus_set_vdcdc(3, 0);
		switch (1 << vdd) {
		case MMC_VDD_33_34:
		case MMC_VDD_32_33:
			mV = 3300;
			break;
		case MMC_VDD_30_31:
		case MMC_VDD_29_30:
			mV = 3000;
			break;
		case MMC_VDD_28_29:
		case MMC_VDD_27_28:
			mV = 2800;
			break;
		case MMC_VDD_24_25:
		case MMC_VDD_23_24:
			mV = 2400;
			break;
		case MMC_VDD_22_23:
		case MMC_VDD_21_22:
			mV = 2200;
			break;
		case MMC_VDD_20_21:
			mV = 2000;
			break;
		case MMC_VDD_165_195:
			mV = 1800;
			break;
		default:
			BUG();
		}
		return menelaus_set_vdcdc(3, mV);
	}
	return 0;
}

static void n810_set_power_emmc(struct device *dev,
					 int power_on)
{
	dev_dbg(dev, "Set EMMC power %s\n", power_on ? "on" : "off");

	if (power_on) {
		gpio_set_value(N810_EMMC_VSD_GPIO, 1);
		msleep(1);
300
		gpio_set_value(N810_EMMC_VIO_GPIO, 1);
301 302
		msleep(1);
	} else {
303
		gpio_set_value(N810_EMMC_VIO_GPIO, 0);
304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454
		msleep(50);
		gpio_set_value(N810_EMMC_VSD_GPIO, 0);
		msleep(50);
	}
}

static int n8x0_mmc_set_power(struct device *dev, int slot, int power_on,
			      int vdd)
{
	if (machine_is_nokia_n800() || slot == 0)
		return n8x0_mmc_set_power_menelaus(dev, slot, power_on, vdd);

	n810_set_power_emmc(dev, power_on);

	return 0;
}

static int n8x0_mmc_set_bus_mode(struct device *dev, int slot, int bus_mode)
{
	int r;

	dev_dbg(dev, "Set slot %d bus mode %s\n", slot + 1,
		bus_mode == MMC_BUSMODE_OPENDRAIN ? "open-drain" : "push-pull");
	BUG_ON(slot != 0 && slot != 1);
	slot++;
	switch (bus_mode) {
	case MMC_BUSMODE_OPENDRAIN:
		r = menelaus_set_mmc_opendrain(slot, 1);
		break;
	case MMC_BUSMODE_PUSHPULL:
		r = menelaus_set_mmc_opendrain(slot, 0);
		break;
	default:
		BUG();
	}
	if (r != 0 && printk_ratelimit())
		dev_err(dev, "MMC: unable to set bus mode for slot %d\n",
			slot);
	return r;
}

static int n8x0_mmc_get_cover_state(struct device *dev, int slot)
{
	slot++;
	BUG_ON(slot != 1 && slot != 2);
	if (slot == 1)
		return slot1_cover_open;
	else
		return slot2_cover_open;
}

static void n8x0_mmc_callback(void *data, u8 card_mask)
{
	int bit, *openp, index;

	if (machine_is_nokia_n800()) {
		bit = 1 << 1;
		openp = &slot2_cover_open;
		index = 1;
	} else {
		bit = 1;
		openp = &slot1_cover_open;
		index = 0;
	}

	if (card_mask & bit)
		*openp = 1;
	else
		*openp = 0;

	omap_mmc_notify_cover_event(mmc_device, index, *openp);
}

static int n8x0_mmc_late_init(struct device *dev)
{
	int r, bit, *openp;
	int vs2sel;

	mmc_device = dev;

	r = menelaus_set_slot_sel(1);
	if (r < 0)
		return r;

	if (machine_is_nokia_n800())
		vs2sel = 0;
	else
		vs2sel = 2;

	r = menelaus_set_mmc_slot(2, 0, vs2sel, 1);
	if (r < 0)
		return r;

	n8x0_mmc_set_power(dev, 0, MMC_POWER_ON, 16); /* MMC_VDD_28_29 */
	n8x0_mmc_set_power(dev, 1, MMC_POWER_ON, 16);

	r = menelaus_set_mmc_slot(1, 1, 0, 1);
	if (r < 0)
		return r;
	r = menelaus_set_mmc_slot(2, 1, vs2sel, 1);
	if (r < 0)
		return r;

	r = menelaus_get_slot_pin_states();
	if (r < 0)
		return r;

	if (machine_is_nokia_n800()) {
		bit = 1 << 1;
		openp = &slot2_cover_open;
	} else {
		bit = 1;
		openp = &slot1_cover_open;
		slot2_cover_open = 0;
	}

	/* All slot pin bits seem to be inversed until first switch change */
	if (r == 0xf || r == (0xf & ~bit))
		r = ~r;

	if (r & bit)
		*openp = 1;
	else
		*openp = 0;

	r = menelaus_register_mmc_callback(n8x0_mmc_callback, NULL);

	return r;
}

static void n8x0_mmc_shutdown(struct device *dev)
{
	int vs2sel;

	if (machine_is_nokia_n800())
		vs2sel = 0;
	else
		vs2sel = 2;

	menelaus_set_mmc_slot(1, 0, 0, 0);
	menelaus_set_mmc_slot(2, 0, vs2sel, 0);
}

static void n8x0_mmc_cleanup(struct device *dev)
{
	menelaus_unregister_mmc_callback();

	gpio_free(N8X0_SLOT_SWITCH_GPIO);

	if (machine_is_nokia_n810()) {
		gpio_free(N810_EMMC_VSD_GPIO);
455
		gpio_free(N810_EMMC_VIO_GPIO);
456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495
	}
}

/*
 * MMC controller1 has two slots that are multiplexed via I2C.
 * MMC controller2 is not in use.
 */
static struct omap_mmc_platform_data mmc1_data = {
	.nr_slots			= 2,
	.switch_slot			= n8x0_mmc_switch_slot,
	.init				= n8x0_mmc_late_init,
	.cleanup			= n8x0_mmc_cleanup,
	.shutdown			= n8x0_mmc_shutdown,
	.max_freq			= 24000000,
	.dma_mask			= 0xffffffff,
	.slots[0] = {
		.wires			= 4,
		.set_power		= n8x0_mmc_set_power,
		.set_bus_mode		= n8x0_mmc_set_bus_mode,
		.get_cover_state	= n8x0_mmc_get_cover_state,
		.ocr_mask		= MMC_VDD_165_195 | MMC_VDD_30_31 |
						MMC_VDD_32_33   | MMC_VDD_33_34,
		.name			= "internal",
	},
	.slots[1] = {
		.set_power		= n8x0_mmc_set_power,
		.set_bus_mode		= n8x0_mmc_set_bus_mode,
		.get_cover_state	= n8x0_mmc_get_cover_state,
		.ocr_mask		= MMC_VDD_165_195 | MMC_VDD_20_21 |
						MMC_VDD_21_22 | MMC_VDD_22_23 |
						MMC_VDD_23_24 | MMC_VDD_24_25 |
						MMC_VDD_27_28 | MMC_VDD_28_29 |
						MMC_VDD_29_30 | MMC_VDD_30_31 |
						MMC_VDD_32_33 | MMC_VDD_33_34,
		.name			= "external",
	},
};

static struct omap_mmc_platform_data *mmc_data[OMAP24XX_NR_MMC];

I
Igor Grinberg 已提交
496 497 498 499
static struct gpio n810_emmc_gpios[] __initdata = {
	{ N810_EMMC_VSD_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vddf" },
	{ N810_EMMC_VIO_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vdd"  },
};
500

I
Igor Grinberg 已提交
501
static void __init n8x0_mmc_init(void)
502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517
{
	int err;

	if (machine_is_nokia_n810()) {
		mmc1_data.slots[0].name = "external";

		/*
		 * Some Samsung Movinand chips do not like open-ended
		 * multi-block reads and fall to braind-dead state
		 * while doing so. Reducing the number of blocks in
		 * the transfer or delays in clock disable do not help
		 */
		mmc1_data.slots[1].name = "internal";
		mmc1_data.slots[1].ban_openended = 1;
	}

I
Igor Grinberg 已提交
518 519
	err = gpio_request_one(N8X0_SLOT_SWITCH_GPIO, GPIOF_OUT_INIT_LOW,
			       "MMC slot switch");
520
	if (err)
521
		return;
522 523

	if (machine_is_nokia_n810()) {
I
Igor Grinberg 已提交
524 525
		err = gpio_request_array(n810_emmc_gpios,
					 ARRAY_SIZE(n810_emmc_gpios));
526 527
		if (err) {
			gpio_free(N8X0_SLOT_SWITCH_GPIO);
528
			return;
529 530 531 532
		}
	}

	mmc_data[0] = &mmc1_data;
533
	omap242x_init_mmc(mmc_data);
534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588
}
#else

void __init n8x0_mmc_init(void)
{
}
#endif	/* CONFIG_MMC_OMAP */

#ifdef CONFIG_MENELAUS

static int n8x0_auto_sleep_regulators(void)
{
	u32 val;
	int ret;

	val = EN_VPLL_SLEEP | EN_VMMC_SLEEP    \
		| EN_VAUX_SLEEP | EN_VIO_SLEEP \
		| EN_VMEM_SLEEP | EN_DC3_SLEEP \
		| EN_VC_SLEEP | EN_DC2_SLEEP;

	ret = menelaus_set_regulator_sleep(1, val);
	if (ret < 0) {
		printk(KERN_ERR "Could not set regulators to sleep on "
			"menelaus: %u\n", ret);
		return ret;
	}
	return 0;
}

static int n8x0_auto_voltage_scale(void)
{
	int ret;

	ret = menelaus_set_vcore_hw(1400, 1050);
	if (ret < 0) {
		printk(KERN_ERR "Could not set VCORE voltage on "
			"menelaus: %u\n", ret);
		return ret;
	}
	return 0;
}

static int n8x0_menelaus_late_init(struct device *dev)
{
	int ret;

	ret = n8x0_auto_voltage_scale();
	if (ret < 0)
		return ret;
	ret = n8x0_auto_sleep_regulators();
	if (ret < 0)
		return ret;
	return 0;
}

589 590 591 592 593 594 595 596 597 598 599 600
#else
static int n8x0_menelaus_late_init(struct device *dev)
{
	return 0;
}
#endif

static struct menelaus_platform_data n8x0_menelaus_platform_data __initdata = {
	.late_init = n8x0_menelaus_late_init,
};

static struct i2c_board_info __initdata n8x0_i2c_board_info_1[] __initdata = {
601 602 603
	{
		I2C_BOARD_INFO("menelaus", 0x72),
		.irq = INT_24XX_SYS_NIRQ,
604
		.platform_data = &n8x0_menelaus_platform_data,
605 606 607
	},
};

608 609
static struct aic3x_pdata n810_aic33_data __initdata = {
	.gpio_reset = 118,
610 611
};

612 613 614 615 616 617
static struct i2c_board_info n810_i2c_board_info_2[] __initdata = {
	{
		I2C_BOARD_INFO("tlv320aic3x", 0x18),
		.platform_data = &n810_aic33_data,
	},
};
618

619 620 621
static void __init n8x0_map_io(void)
{
	omap2_set_globals_242x();
622
	omap242x_map_common_io();
623 624
}

625
static void __init n8x0_init_early(void)
626
{
627 628
	omap2_init_common_infrastructure();
	omap2_init_common_devices(NULL, NULL);
629 630
}

631 632
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
633 634 635 636 637
	/* I2S codec port pins for McBSP block */
	OMAP2420_MUX(EAC_AC_SCLK, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
	OMAP2420_MUX(EAC_AC_FS, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
	OMAP2420_MUX(EAC_AC_DIN, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
	OMAP2420_MUX(EAC_AC_DOUT, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
638 639
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676

static struct omap_device_pad serial2_pads[] __initdata = {
	{
		.name	= "uart3_rx_irrx.uart3_rx_irrx",
		.flags	= OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
		.enable	= OMAP_MUX_MODE0,
		.idle	= OMAP_MUX_MODE3	/* Mux as GPIO for idle */
	},
};

static inline void board_serial_init(void)
{
	struct omap_board_data bdata;

	bdata.flags = 0;
	bdata.pads = NULL;
	bdata.pads_cnt = 0;

	bdata.id = 0;
	omap_serial_init_port(&bdata);

	bdata.id = 1;
	omap_serial_init_port(&bdata);

	bdata.id = 2;
	bdata.pads = serial2_pads;
	bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
	omap_serial_init_port(&bdata);
}

#else

static inline void board_serial_init(void)
{
	omap_serial_init();
}

677 678
#endif

679 680
static void __init n8x0_init_machine(void)
{
681
	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
682 683 684
	/* FIXME: add n810 spi devices */
	spi_register_board_info(n800_spi_board_info,
				ARRAY_SIZE(n800_spi_board_info));
685 686
	omap_register_i2c_bus(1, 400, n8x0_i2c_board_info_1,
			      ARRAY_SIZE(n8x0_i2c_board_info_1));
687 688 689 690
	omap_register_i2c_bus(2, 400, NULL, 0);
	if (machine_is_nokia_n810())
		i2c_register_board_info(2, n810_i2c_board_info_2,
					ARRAY_SIZE(n810_i2c_board_info_2));
691
	board_serial_init();
692
	gpmc_onenand_init(board_onenand_data);
693
	n8x0_mmc_init();
694
	n8x0_usb_init();
695 696 697 698
}

MACHINE_START(NOKIA_N800, "Nokia N800")
	.boot_params	= 0x80000100,
699
	.reserve	= omap_reserve,
700 701 702
	.map_io		= n8x0_map_io,
	.init_early	= n8x0_init_early,
	.init_irq	= omap_init_irq,
703 704 705 706 707 708
	.init_machine	= n8x0_init_machine,
	.timer		= &omap_timer,
MACHINE_END

MACHINE_START(NOKIA_N810, "Nokia N810")
	.boot_params	= 0x80000100,
709
	.reserve	= omap_reserve,
710 711 712
	.map_io		= n8x0_map_io,
	.init_early	= n8x0_init_early,
	.init_irq	= omap_init_irq,
713 714 715 716 717 718
	.init_machine	= n8x0_init_machine,
	.timer		= &omap_timer,
MACHINE_END

MACHINE_START(NOKIA_N810_WIMAX, "Nokia N810 WiMAX")
	.boot_params	= 0x80000100,
719
	.reserve	= omap_reserve,
720 721 722
	.map_io		= n8x0_map_io,
	.init_early	= n8x0_init_early,
	.init_irq	= omap_init_irq,
723 724 725
	.init_machine	= n8x0_init_machine,
	.timer		= &omap_timer,
MACHINE_END