Kconfig 6.9 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11
menu "Hardware Drivers Config"

config SOC_STM32F103ZE
    bool
    select SOC_SERIES_STM32F1
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable USB TO USART (uart1)"
S
SummerGift 已提交
12
        select BSP_USING_UART
13 14 15 16 17 18 19 20 21 22
        select BSP_USING_UART1
        default y

    config BSP_USING_RS485_OR_RS232
        bool "Enable RS485/RS232 (uart2 be shared)"
        select BSP_USING_UART2
        default n

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (w25q64 spi1)"
S
SummerGift 已提交
23
        select BSP_USING_SPI
24 25 26 27 28
        select BSP_USING_SPI1
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

29 30 31 32 33 34 35 36 37 38
    config BSP_USING_RGB
        bool "Enable RGB LED (timer3 channel2 - 4)"
        select RT_USING_PWM
        select BSP_USING_PWM
        select BSP_USING_PWM3
        select BSP_USING_PWM3_CH2
        select BSP_USING_PWM3_CH3
        select BSP_USING_PWM3_CH4
        default n

39 40 41 42 43 44
    config BSP_USING_POT
        bool "Enable potentiometer"
        select BSP_USING_ADC
        select BSP_USING_ADC1
        default n  

45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77
    config BSP_USING_EEPROM
        bool "Enable I2C EEPROM (i2c1)"
        select BSP_USING_I2C1
        default n

    config BSP_USING_ETH
        bool "Enable Ethernet Driver (spi2)"
        default n
        select PKG_USING_WIZNET
        select WIZNET_DEVICE_EXTERN_CONFIG
        select BSP_USING_SPI2
        if BSP_USING_ETH

            if WIZNET_DEVICE_EXTERN_CONFIG
                config WIZ_SPI_DEVICE
                    string
                    default "spi20"

                config WIZ_RST_PIN
                    int
                    default 111

                config WIZ_IRQ_PIN
                    int
                    default 104
            endif

            config EXTERNAL_PHY_ADDRESS
                hex
                default 0x00

        endif

78 79 80 81 82 83 84
    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

85 86 87 88 89 90 91 92 93
endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

S
SummerGift 已提交
94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126
    menuconfig BSP_USING_UART
    bool "Enable UART"
    default y
    select RT_USING_SERIAL
    if BSP_USING_UART
        config BSP_USING_UART1
            bool "Enable UART1"
            default y

        config BSP_UART1_RX_USING_DMA
            bool "Enable UART1 RX DMA"
            depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
            default n

        config BSP_USING_UART2
            bool "Enable UART2"
            default n

        config BSP_UART2_RX_USING_DMA
            bool "Enable UART2 RX DMA"
            depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
            default n
            
        config BSP_USING_UART3
            bool "Enable UART3"
            default n

        config BSP_UART3_RX_USING_DMA
            bool "Enable UART3 RX DMA"
            depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
            default n  
    endif
   
127 128 129 130
    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

S
SummerGift 已提交
131 132
    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
133 134
        default n
        select RT_USING_SPI
S
SummerGift 已提交
135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n
                
            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n  
                
            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n
                
            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
                
            config BSP_USING_SPI3
                bool "Enable SPI3 BUS"
                default n        

            config BSP_SPI3_TX_USING_DMA
                bool "Enable SPI3 TX DMA"
                depends on BSP_USING_SPI3
                default n
                
            config BSP_SPI3_RX_USING_DMA
                bool "Enable SPI3 RX DMA"
                depends on BSP_USING_SPI3
                select BSP_SPI3_TX_USING_DMA
                default n  
        endif
181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 175
                default 22
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 175
                default 23
        endif

199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243
    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM2
                bool "Enable TIM2"
                default n

            config BSP_USING_TIM3
                bool "Enable TIM3"
                default n

            config BSP_USING_TIM4
                bool "Enable TIM4"
                default n

            config BSP_USING_TIM5
                bool "Enable TIM5"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM3
            bool "Enable timer3 output pwm"
            default n
            if BSP_USING_PWM3
                config BSP_USING_PWM3_CH2
                    bool "Enable PWM3 channel2"
                    default n

                config BSP_USING_PWM3_CH3
                    bool "Enable PWM3 channel3"
                    default n

                config BSP_USING_PWM3_CH4
                    bool "Enable PWM3 channel4"
                    default n
            endif
        endif

244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264
    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    config BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        select RT_USING_LIBC
        default n

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

265 266 267 268 269 270
    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

271 272 273 274 275 276 277
endmenu

menu "Board extended module Drivers"

endmenu

endmenu