Kconfig 6.2 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11
menu "Hardware Drivers Config"

config SOC_STM32F429IG
    bool
    select SOC_SERIES_STM32F4
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable USB TO USART (uart1)"
S
SummerGift 已提交
12
        select BSP_USING_UART
13 14 15 16
        select BSP_USING_UART1
        default y

    config BSP_USING_COM2
S
SummerGift 已提交
17
        bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)"
S
SummerGift 已提交
18
	select BSP_USING_UART
19 20
        select BSP_USING_UART2
        default n
21

22
    config BSP_USING_COM3
S
SummerGift 已提交
23
        bool "Enable COM3 (uart3 pin conflict with Ethernet)"
24 25
        select BSP_USING_UART3
        default n
26 27 28 29 30

    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        default n

31 32
    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (w25q256 spi5)"
S
SummerGift 已提交
33
        select BSP_USING_SPI
34 35 36 37
        select BSP_USING_SPI5
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n
38

39 40 41 42 43 44
    config BSP_USING_MPU9250
        bool "Enable MPU 9250 (i2c1)"
        select BSP_USING_I2C1
        select PKG_USING_MPU6XXX
        default n

S
SummerGift 已提交
45 46
    config PHY_USING_LAN8720A
        bool
S
SummerGift 已提交
47

48 49
    config BSP_USING_ETH
        bool "Enable Ethernet"
S
SummerGift 已提交
50 51
        select BSP_USING_I2C1
        select PKG_USING_PCF8574
52
        select RT_USING_LWIP
S
SummerGift 已提交
53
        select PHY_USING_LAN8720A
S
SummerGift 已提交
54
        default n
55 56 57 58 59 60 61 62

    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

63 64 65 66 67 68 69 70 71
endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

S
SummerGift 已提交
72 73
    menuconfig BSP_USING_UART
        bool "Enable UART"
74 75
        default y
        select RT_USING_SERIAL
S
SummerGift 已提交
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default y

            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n
                
            config BSP_USING_UART3
                bool "Enable UART3"
                default n
   
            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n  
        endif
104

105 106 107 108
    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

S
SummerGift 已提交
109 110
    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
111 112
        default n
        select RT_USING_SPI
S
SummerGift 已提交
113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n
                
            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n  
                
            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n
                
            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
                
            config BSP_USING_SPI5
                bool "Enable SPI5 BUS"
                default n        

            config BSP_SPI5_TX_USING_DMA
                bool "Enable SPI5 TX DMA"
                depends on BSP_USING_SPI5
                default n
                
            config BSP_SPI5_RX_USING_DMA
                bool "Enable SPI5 RX DMA"
                depends on BSP_USING_SPI5
                select BSP_SPI5_TX_USING_DMA
                default n  
        endif
159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            comment "Notice: PH4 --> 116; PH5 --> 117"
            config BSP_I2C1_SCL_PIN
                int "I2C1 scl pin number"
                range 1 176
                default 116
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 1 176
                default 117
        endif

178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210
    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM11
                bool "Enable TIM11"
                default n

            config BSP_USING_TIM13
                bool "Enable TIM13"
                default n

            config BSP_USING_TIM14
                bool "Enable TIM14"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM2
            bool "Enable timer2 output pwm"
            default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH4
                    bool "Enable PWM2 channel4"
                    default n
            endif
        endif

211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231
    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    config BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        select RT_USING_LIBC
        default n

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

232 233 234 235 236 237
    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

238 239 240 241 242 243 244
endmenu

menu "Board extended module Drivers"

endmenu

endmenu