Kconfig

menu "Hardware Drivers Config"

config SOC_STM32F103RB
    bool
    select SOC_SERIES_STM32F1
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable USB TO USART (uart1)"
        select BSP_USING_UART
        select BSP_USING_UART1
        default y

    config BSP_USING_EEPROM
        bool "Enable I2C EEPROM (i2c1)"
        select BSP_USING_I2C1
        default n

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (w25q16 spi2)"
	select BSP_USING_SPI
        select BSP_USING_SPI2
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_POT
        bool "Enable potentiometer"
        select BSP_USING_ADC
        select BSP_USING_ADC1
        default n 

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
    bool "Enable UART"
    default y
    select RT_USING_SERIAL
    if BSP_USING_UART
        config BSP_USING_UART1
            bool "Enable UART1"
            default y

        config BSP_UART1_RX_USING_DMA
            bool "Enable UART1 RX DMA"
            depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
            default n

        config BSP_USING_UART2
            bool "Enable UART2"
            default n

        config BSP_UART2_RX_USING_DMA
            bool "Enable UART2 RX DMA"
            depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
            default n
            
        config BSP_USING_UART3
            bool "Enable UART3"
            default n

        config BSP_UART3_RX_USING_DMA
            bool "Enable UART3 RX DMA"
            depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
            default n  
    endif    
        
    config BSP_USING_UART1
        bool "Enable UART1"
        select RT_USING_SERIAL
        default y

    config BSP_USING_UART2
        bool "Enable UART2"
        select RT_USING_SERIAL
        default n

    config BSP_USING_UART3
        bool "Enable UART3"
        select RT_USING_SERIAL
        default n

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM2
                bool "Enable TIM2"
                default n

            config BSP_USING_TIM3
                bool "Enable TIM3"
                default n

            config BSP_USING_TIM4
                bool "Enable TIM4"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM3
            bool "Enable timer3 output pwm"
            default n
            if BSP_USING_PWM3
                config BSP_USING_PWM3_CH1
                    bool "Enable PWM3 channel1"
                    default n

                config BSP_USING_PWM3_CH2
                    bool "Enable PWM3 channel2"
                    default n
            endif
        endif
	
    menuconfig BSP_USING_SPI
    bool "Enable SPI BUS"
    default n
    select RT_USING_SPI
    if BSP_USING_SPI
        config BSP_USING_SPI1
            bool "Enable SPI1 BUS"
            default n

        config BSP_SPI1_TX_USING_DMA
            bool "Enable SPI1 TX DMA"
            depends on BSP_USING_SPI1
            default n
                    
        config BSP_SPI1_RX_USING_DMA
            bool "Enable SPI1 RX DMA"
            depends on BSP_USING_SPI1
            select BSP_SPI1_TX_USING_DMA
            default n

        config BSP_USING_SPI2
            bool "Enable SPI2 BUS"
            default n  
                    
        config BSP_SPI2_TX_USING_DMA
            bool "Enable SPI2 TX DMA"
            depends on BSP_USING_SPI2
            default n
                    
        config BSP_SPI2_RX_USING_DMA
            bool "Enable SPI2 RX DMA"
            depends on BSP_USING_SPI2
            select BSP_SPI2_TX_USING_DMA
            default n
    endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 63
                default 22
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 63
                default 23
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n 

    config BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        select RT_USING_LIBC
        default n

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

endmenu

menu "Board extended module Drivers"

endmenu

endmenu