board.h

/*
 * File      : board.h
 * This file is part of RT-Thread RTOS
 * COPYRIGHT (C) 2009, RT-Thread Development Team
 *
 * The license and distribution terms for this file may be
 * found in the file LICENSE in this distribution or at
 * http://www.rt-thread.org/license/LICENSE
 *
 * Change Logs:
 * Date           Author       Notes
 * 2009-09-22     Bernard      add board.h to this bsp
 */

// <<< Use Configuration Wizard in Context Menu >>>
#ifndef __BOARD_H__
#define __BOARD_H__

#include <stm32f2xx.h>

/* board configuration */
// <o> SDCard Driver <1=>SDIO sdcard <0=>SPI MMC card
// 	<i>Default: 1
#define STM32_USE_SDIO			1

/* whether use board external SRAM memory */
// <e>Use external SRAM memory on the board
// 	<i>Enable External SRAM memory
#define STM32_EXT_SRAM          0
//	<o>Begin Address of External SRAM
//		<i>Default: 0x68000000
#define STM32_EXT_SRAM_BEGIN    0x68000000 /* the begining address of external SRAM */
//	<o>End Address of External SRAM
//		<i>Default: 0x68080000
#define STM32_EXT_SRAM_END      0x68080000 /* the end address of external SRAM */
// </e>

// <o> Internal SRAM memory size[Kbytes] <8-128>
//	<i>Default: 64
#define STM32_SRAM_SIZE         128
#define STM32_SRAM_END          (0x20000000 + STM32_SRAM_SIZE * 1024)

// <o> Console on USART: <0=> no console <1=>USART 1 <2=>USART 2 <3=> USART 3
// 	<i>Default: 1
#define STM32_CONSOLE_USART		1

// <o> Ethernet Interface: <0=> Microchip ENC28J60
#define STM32_ETH_IF			0

void rt_hw_board_led_on(int n);
void rt_hw_board_led_off(int n);
void rt_hw_board_init(void);

#if STM32_CONSOLE_USART == 0
#define CONSOLE_DEVICE "no"
#elif STM32_CONSOLE_USART == 1
#define CONSOLE_DEVICE "uart1"
#elif STM32_CONSOLE_USART == 2
#define CONSOLE_DEVICE "uart2"
#elif STM32_CONSOLE_USART == 3
#define CONSOLE_DEVICE "uart3"
#endif

#if STM32_USE_SDIO
/**
  * @brief  SD FLASH SDIO Interface
  */
#define SD_DETECT_PIN                    GPIO_Pin_0                 /* PB.0 */
#define SD_DETECT_GPIO_PORT              GPIOB                       /* GPIOB */
#define SD_DETECT_GPIO_CLK               RCC_AHB1Periph_GPIOB
   
#define SDIO_FIFO_ADDRESS                ((uint32_t)0x40012C80)
/** 
  * @brief  SDIO Intialization Frequency (400KHz max)
  */
#define SDIO_INIT_CLK_DIV                ((uint8_t)0x76)
/** 
  * @brief  SDIO Data Transfer Frequency (25MHz max) 
  */
#define SDIO_TRANSFER_CLK_DIV            ((uint8_t)0x0) 

#define SD_SDIO_DMA                   DMA2
#define SD_SDIO_DMA_CLK               RCC_AHB1Periph_DMA2
 
#define SD_SDIO_DMA_STREAM3	          3
//#define SD_SDIO_DMA_STREAM6           6

#ifdef SD_SDIO_DMA_STREAM3
 #define SD_SDIO_DMA_STREAM            DMA2_Stream3
 #define SD_SDIO_DMA_CHANNEL           DMA_Channel_4
 #define SD_SDIO_DMA_FLAG_FEIF         DMA_FLAG_FEIF3
 #define SD_SDIO_DMA_FLAG_DMEIF        DMA_FLAG_DMEIF3
 #define SD_SDIO_DMA_FLAG_TEIF         DMA_FLAG_TEIF3
 #define SD_SDIO_DMA_FLAG_HTIF         DMA_FLAG_HTIF3
 #define SD_SDIO_DMA_FLAG_TCIF         DMA_FLAG_TCIF3 
#elif defined SD_SDIO_DMA_STREAM6
 #define SD_SDIO_DMA_STREAM            DMA2_Stream6
 #define SD_SDIO_DMA_CHANNEL           DMA_Channel_4
 #define SD_SDIO_DMA_FLAG_FEIF         DMA_FLAG_FEIF6
 #define SD_SDIO_DMA_FLAG_DMEIF        DMA_FLAG_DMEIF6
 #define SD_SDIO_DMA_FLAG_TEIF         DMA_FLAG_TEIF6
 #define SD_SDIO_DMA_FLAG_HTIF         DMA_FLAG_HTIF6
 #define SD_SDIO_DMA_FLAG_TCIF         DMA_FLAG_TCIF6 
#endif /* SD_SDIO_DMA_STREAM3 */

void SD_LowLevel_DeInit(void);
void SD_LowLevel_Init(void); 
void SD_LowLevel_DMA_TxConfig(uint32_t *BufferSRC, uint32_t BufferSize);
void SD_LowLevel_DMA_RxConfig(uint32_t *BufferDST, uint32_t BufferSize);

#endif
void rt_hw_usart_init(void);

/* SD Card init function */
void rt_hw_msd_init(void);

/* ETH interface init function */

#endif

// <<< Use Configuration Wizard in Context Menu >>>