void * __iomem foo is not a pointer to iomem - it's an iomem variable
containing void *.  A pile of such guys in arch/sparc64/kernel/time.c,
drivers/sbus/char/rtc.c and include/asm-sparc64/mostek.h turned into
intended void __iomem *. 
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Missing include - usual portability problems...
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

(!ARCH_S390 && !M68K && !IA64 && !UML) is obviously always true on ARM.

Intended behaviour for ARM is "absent unless we are on RiscPC or
EBSA285".  So what we want is added && !ARM in the first term - without
it the last part (|| ARCH_RPC || ARCH_EBSA285, that is) doesn't do
anything. 
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Missing include, breaks at least on arm.
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Turns __get_unaligned() and __put_unaligned into macros.  That is
definitely safe; leaving them as inlines breaks on e.g.  alpha [try to
build ncpfs there and you'll get unresolved symbols since we end up
getting __get_unaligned() not inlined]. 
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

All boards dealt with by I2C_MPC are 32bit.  Moreover, driver simply
won't build on ppc64 - it uses ppc32-only types all over the place. 
Dependency fixed - it's PPC32, not PPC. 
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

CONFIG_HW_CONSOLE selects vt.c; without the stuff pulled by CONFIG_VT it
will not build.  Normally we get both in drivers/char/Kconfig and there
HW_CONSOLE depends on VT.  sparc64 does not pull drivers/char/Kconfig
and has that sutff in arch/sparc64/Kconfig instead.  However, it forgets
to add the same dependency.  As the result, turning VT off [which is
possible] will end up with broken build.  For no good reason... 
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Dumb typo - __get_free_page() takes gfp mask (in this case -
GFP_KERNEL), not the page size... 
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

zonelist_policy() forgot to mask non-zone bits from gfp when comparing
zone number with policy_zone. 
ACKed-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Somebody forgot that | has higher priority than ?:.  As the result,
allocation is done with bogus flags - instead of GFP_ATOMIC + possibly
GFP_DMA we always get GFP_DMA and no GFP_ATOMIC. 
Signed-off-by: NAl Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

This patch is required to support cpu removal for IPF systems. Existing code
just fakes the real offline by keeping it run the idle thread, and polling
for the bit to re-appear in the cpu_state to get out of the idle loop.

For the cpu-offline to work correctly, we need to pass control of this CPU 
back to SAL so it can continue in the boot-rendez mode. This gives the
SAL control to not pick this cpu as the monarch processor for global MCA
events, and addition does not wait for this cpu to checkin with SAL
for global MCA events as well. The handoff is implemented as documented in 
SAL specification section 3.2.5.1 "OS_BOOT_RENDEZ to SAL return State"
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Found by Alexander Nyberg, improved by Bjorn Helgaas.

- Fix the incorrect argument to sizeof()
- looks like memcpy() code pass was dervived from code that used
  copy_from_user().  But in this case we are doing to kernel space
  to kernel space copy, so memcpy is the right routine, but it
  doesn't return an error code.
Signed-off-by: NArun Sharma <arun.sharma@intel.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The labels after the last put_user patch were misplaced so
exceptions on the real mov instructions would not be handled.

Noted by Brian Gerst <bgerst@didntduck.org>

This breaks serial consoles badly.  Thanks to Eric Brower
for tracking down the problem.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were forgetting to call sunsu_change_speed().  The reason
that replugging in the mouse cable "fixes things" is that
causes a BREAK interrupt which in turn caused a call to
sunsu_change_speed() which would get the chip setup properly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide support for drivers/char/rtc.c ioctls in the
Mostek rtc driver as well as the Sparc specific RTCGET
and RTCSET.

This allows userspace to be much less messy.  Currently
util-linux and other spots jump through hoops trying
various ioctl variants until it hits the right one whatever
driver actually being used supports.

Eventually all of this should move over to the genrtc.c
driver, but not today...

While we are here, fix up the register types for sparse.

Thanks to Frans Pop for helping point out this issue.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use 'daddr' instead of &tmpl->id.daddr, since the latter
might be zero.  Also, only perform the lookup when
tmpl->id.spi is non-zero.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MSI test for chips that support MSI. If MSI test fails, it will
switch back to INTx mode and will print a message asking the user to
report the failure.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MSI support for 5751 C0 and 5752.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug in tg3_set_eeprom() when the length is less than 4 and the
offset is not 4-byte aligned.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out
is enabled, certain NVRAM registers cannot be written to.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as
output when it is unused.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround
it is to change it to the correct value in tp->pci_chip_rev_id. This
way, it is easier to check for the ASIC_REV_5752 in the rest of the
driver.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix tg3_set_power_state to drive GPIOs properly based on the
TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0
and D3 power state changes.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setup proper GPIO settings in tp->grc_local_ctrl before calling
tg3_set_power() state in tg3_get_invariants() and after chip reset.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so
that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling
tg3_set_power_state() in tg3_get_invariants(). This will allow
tg3_set_power_state() to drive the GPIOs correctly based on the config.
information in eeprom.

On the 5752, there are no pull-up resistors on the GPIO pins and it is
necessary to drive the unused GPIOs as output.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some minor 5752 fixes mostly for correctness and add 5752 PHY ID.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use check of TG3_FLG2_5750_PLUS in tg3_get_invariants to set
TG3_FLG2_5705_PLUS flag.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rewrite checks in tg3_get_invariants to use TG3_FLG2_5705_PLUS and
TG3_FLG2_5750_PLUS flags.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rewrite of a couple of troublesome multi-way if statements to use
TG3_FLG2_5705_PLUS flag.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace a number of two-way if statements checking for 5750, and/or
5752 to reference the newly-defined TG3_FLG2_5750_PLUS flag instead.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for
ASIC_REV_5750 or ASIC_REV_5752.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace a number of three-way if statements checking for 5705, 5750,
and 5752 to reference the equivalent TG3_FLG2_5705_PLUS flag instead.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3.
I did this separately in case patches like this (i.e. new PCI IDs)
need to come from more "official" sources.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add hard-coded definition of bcm5752 PCI ID to tg3_pci_tbl.
Next patch will change entry to use pci_ids.h-based definition.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>