- 25 7月, 2009 2 次提交
-
-
由 Johannes Berg 提交于
Use %pM instead, and also remove stray variables declared with DECLARE_MAC_BUF. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Acked-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch roughly implements xmit aggregation for ar9170-like device. Not all AP are compatible with the driver(and firmware) yet, so YMMV. A more refined code will definitely need the final HT specification to be available for the public, lots of firmware modification and possibly a redesigned driver just for good measure. Sadly, these conditions won't come true anytime soon... Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 7月, 2009 1 次提交
-
-
由 Johannes Berg 提交于
Within mac80211, we often need to copy the rx status into skb->cb. This is wasteful, as drivers could be building it in there to start with. This patch changes the API so that drivers are expected to pass the RX status in skb->cb, now accessible as IEEE80211_SKB_RXCB(skb). It also updates all drivers to pass the rx status in there, but only by making them memcpy() it into place before the call to the receive function (ieee80211_rx(_irqsafe)). Each driver can now be optimised on its own schedule. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 6月, 2009 2 次提交
-
-
由 Christian Lamparter 提交于
This patch is a back-port from aggregation testing code. In the past, we didn't limit the amount of active tx urbs. However, ar9170 only has a limited buffer reserved for pending data frames. This wasn't much of a problem with the slower 802.11b/g. We simply stopped the full queue and moved on to something different in the mean time. But - as you guessed it - this simple approach stands in way for a decent aggregation implementation. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This adds new commands that the original firmware will not send but we can use them to debug firmware. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 04 6月, 2009 6 次提交
-
-
由 Christian Lamparter 提交于
This patch removes code (deprecated by "cfg80211: add rfkill support" ) main.c: In function 'ar9170_op_config': main.c:1306: warning: '__IEEE80211_CONF_CHANGE_RADIO_ENABLED' is deprecated (declared at include/net/mac80211.h:551) and a useless device state. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch contains a few more mostly random fixes for the USB front-end. 1. handle irq command response, instead of printing it to the console. 2. remove fixed FIXME. (real fix: "ar9170usb: reset device on resume". ) 3. some more one-liner. - get rid of a useless "return;" - add a few branch prediction hints in hot-paths etc. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch takes care of Johannes' deadlock report by moving the mutex_lock right after cancel_work_sync in ar9170_op_stop. Besides, the janitor does not need to hold the mutex anymore, so this extra lines can be removed as well. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch removes a redundant flag. .cap = IEEE80211_HT_CAP_MAX_AMSDU | \ > IEEE80211_HT_CAP_SM_PS | \ < [...] \ > IEEE80211_HT_CAP_SM_PS, \ < .ampdu_factor = 3, \ Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch fixes a bug in configure_filter's (sub-)routines. We never really cleared the flags once we updated the hardware state, so we wasted our resources by applying already active settings. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch introduces 3 new function which are used to update the MAC state, whenever needed... e.g: after a band switch. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 5月, 2009 1 次提交
-
-
由 Zhu Yi 提交于
The patch moves some utility functions from mac80211 to cfg80211. Because these functions are doing generic 802.11 operations so they are not mac80211 specific. The moving allows some fullmac drivers to be also benefit from these utility functions. Signed-off-by: NZhu Yi <yi.zhu@intel.com> Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 5月, 2009 3 次提交
-
-
由 Christian Lamparter 提交于
Otus uses slightly different set of "Minimum MPDU Start Spacing" values than the 802.11n D2.0 specifies. (the whole table is shifted by one and therefore the 16us spacing is not officially available!) And while we're at it, we also initialize our MAC's density register. So, this annoying _feature_ will not break TX A-MPDU later. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The config_interface method is a little strange, it contains the BSSID and beacon updates, while bss_info_changed contains most other BSS information for each interface. This patch removes config_interface and rolls all the information it previously passed to drivers into bss_info_changed. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
We currently have two beacon interval configuration knobs: hw.conf.beacon_int and vif.bss_info.beacon_int. This is rather confusing, even though the former is used when we beacon ourselves and the latter when we are associated to an AP. This just deprecates the hw.conf.beacon_int setting in favour of always using vif.bss_info.beacon_int. Since it touches all the beaconing IBSS code anyway, we can also add support for the cfg80211 IBSS beacon interval configuration easily. NOTE: The hw.conf.beacon_int setting is retained for now due to drivers still using it -- I couldn't untangle all drivers, some are updated in this patch. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 4月, 2009 6 次提交
-
-
由 Christian Lamparter 提交于
With this patch ar9170 is capable of receiving aggregated 802.11n frames and sniffing on most networks without having a "debug message overhead". (Includes phy initialization requested by Johannes Berg <johannes@sipsolutions.net> -- JWL) Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch adds support for configuring HT40 channels and receiving HT40 to ar9170. Receiving aggregation doesn't seem to work right now, so it's not enabled. Same goes for TX aggregation, but that probably needs even more work. With this, I can receive roughly 33 Mbits/sec. The HT capabilities are a little odd, I tried following otus here -- in particular having SGI_40 but not SGI_20 is a little weird but afaict that's what otus does. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
When the EEPROM is not in good condition we cannot continue so we currently bail out but only ath5k is bailing out properly. Both ath9k and ar9170 were proceeding and if a user were to run into this they'd see an obscure panic. Lets propagate the error as intended and make sure we inform the user by lifting the error message from debug to a kernel error. Stable note: You can find a port of this page here: http://bombadil.infradead.org/~mcgrof/patches/ath9k/ath9k-fix-eeprom.patch.txt Cc: stable@kernel.org Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch fixes a locking problem which freezes the network core. The deadlock goes as follows: - ar9170_op_stop - is called 1. change the state to IDLE 2. > take the MUTEX < 3. cancel_SYNC all pending work, which means "block until a work_struct's callback has terminated" => if filter_config_work was queued it tries to get the MUTEX, before checking the device state... Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 3月, 2009 3 次提交
-
-
由 Christian Lamparter 提交于
This patch restores all-in-one module build procedure for ar9170. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch simplifies the tx_status report code by using four tx_queues per station instead of only one. (the skb lookup should be in O(1) now :-p ). Also, it fixes a really obvious copy&paste bug in the janitor work code and adds back a few spilled bits to the hardware definition header about QoS. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch contains almost all mac80211 interaction code of AR9170. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-