- 23 4月, 2009 40 次提交
-
-
由 Johannes Berg 提交于
We don't currently support antenna or rate setting, so remove that. Also update the link -- the current one is dead and the wiki can be kept updated easier. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
In the normal WPA or RSN case keys are only configured after associating, so we should do that in that order when resuming as well. It shouldn't really matter since we do not send any data at either point, but iwlwifi prefers it this way and it does seem more natural. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bing Zhao 提交于
libertas: add support for Marvell SD8688 chip Use RxPD->pkt_ptr to locate eth803 header in the packet received since SD8688/v10 firmware allows a gap between RxPD and eth803 header. Set SDIO block size to 256 for CMD53. The maximum block size for SD8688 WLAN function is set to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size results upto 2K bytes data (4 blocks) being transferred and causes buffer overflow in firmware. Both changes above are backward compatible with earlier firmware versions for SD8385/SD8686. The SDIO_DEVICE_IDs for SD8688 chip are added in include/linux/mmc/sdio_ids.h Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Max Filippov 提交于
p54spi_wakeup and p54spi_tx_frame used busy-waiting loop to poll for 'ready' bits in SPI_ADRS_HOST_INTERRUPTS register. With this change in place 'WR_READY timeout' messages do not show anymore. Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com> Acked-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
This adds support for the LEDs on the Jupiter netbook. Reported-by: NMartin Bammer <mrb74@gmx.at> Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Anna Neal 提交于
Currently, the libertas main thread contends with the spi driver thread in the TX path. To improve throughput, ensure that the driver thread has higher scheduling priority than the libertas main thread. Do this by making the libertas spi driver thread a low priority real time thread. We measured an average throughput improvement of 13%. Signed-off-by: NAnna Neal <anna@cozybit.com> Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This adds the necessary code and fields to let drivers specify their cipher capabilities and exports them to userspace. Also update mac80211 to export the ciphers it has. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
This informs userspace when a change has occured on a world roaming wiphy's channel which has lifted some restrictions due to a regulatory beacon hint. Because this is now sent to userspace through the regulatory multicast group we remove the debug prints we used to use as they are no longer necessary. Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
This adds a netlink channel put helper, nl80211_msg_put_channel(), which we will also make use of later for the beacon hints events. Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
As part of our documented API we always respect the orig_flag settings on a channel. We forgot to follow this for the beacon hints. Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
This patch adding few more debug messages if encounter error when driver try to start tx aggregation queue. Also change from IWL_ERR to IWL_DEBUG_HT is the HW legacy queue is empty when driver request to move to aggregation queue. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
Separated the MIMO tpt matrix into MIMO2 and MIMO3, adding MIMO3 support in rate scaling algorithm. If the device support 3x3, then utilize all three antenna (A/B/C) for tx to improve throughput. Adding rs_switch_to_mimo3() function to allow switch to mimo3 modulation mode from other modes(legacy/siso/mimo2). Adding rs_move_mimo3_to_other() function to allow switch from mimo3 modulation mode to either siso or mimo2; also support toggle between SGI and NGI. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
Adding ht triple_stream_basic_rates for MIMO3 supports Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Fabio Rossi 提交于
When the EEPROM contains weird values for the power levels we have to fix the interpolation process. Signed-off-by: NFabio Rossi <rossi.f@inwind.it> Acked-by: NNick Kossifidis <mickflemm@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Auto-depend on HW_RANDOM, rather than "select"ing it. This way the user has the choice to enable or disable HWRNG support. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
When using nl80211 association, we need to send association response with a failure code to user space SME instead of just internally trying to send out the same (re)association request again couple of times. This fixes problems in association process getting stuck on a failure when user space is not notified in any way that something actually failed. Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Include the HT capabilities in the probe request frame. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Instead of just passing the cfg80211-requested IEs, pass the locally generated ones as well. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch introduces a new attribute for a wiphy that tells userspace how long the information elements added to a probe request frame can be at most. It also updates the at76 to advertise that it cannot support that, and, for now until I can fix that, iwlwifi too. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
drivers/net/wireless/ath/ath5k/led.c:81:6: warning: symbol 'ath5k_led_on' was not declared. Should it be static? Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
Make ath5k select the ath module and add in the hooks to make the eeprom regulatory hint and reg notifier take effect. Changes to attach.c Changes-licensed-under: ISC Changes to base.c Changes-licensed-under: 3-Clause-BSD Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
Setup the wiphy regulatory parameters when first initializing the Atheros regulatory module. We can remove five exported symbols this way and simplify the driver code for both ath5k and ath9k. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
This change creates a new module, ath.ko, which includes code that can be shared between ath5k, ath9k and ar9170. For now, extract most of the ath9k regulatory code so it can also be used in ath5k. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
All regulatory information is encapsulated by the ath9k_regulatory struct, so we can now change all the callers to take that directly instead of struct ath_hw. This in turn will enable us to move the regulatory functions to common code also used by ath5k, since both can use this regulatory struct. Signed-off-by: NBob Copeland <me@bobcopeland.com> Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
Until ath5k and ath9k share common channel structures, they will have to implement their own get_ctl() function. Split out the portion that only relies on the current band and reg domain so that it can be common code. Signed-off-by: NBob Copeland <me@bobcopeland.com> Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Reinette Chatre 提交于
The STATUS_ALIVE value cannot be used because it is cleared when interface is brought down and will not be set if rfkill is enabled when interface is started again. The interface can thus not be brought up if rfkill was enabled before stopping the interface and disabled after starting the interface. Change the test to use priv->is_open instead, this will be set when interface is started whether rfkill is enabled or not. Thanks to Helmut Schaa for the suggested fix. Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Convert scan function to cfg80211. Unlike old scan code new code waits 1 sec before getting scan data from device and passing forward to cfg80211. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Change quality level scale to match cfg80211 CFG80211_SIGNAL_TYPE_UNSPEC. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Added cfg80211_inform_bss() for full-mac devices to use. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> [edit: made rndis_change_virtual_intf static] Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch adds beacon filtering support to p54. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch hopefully finishes the SoftLED code: - It adds two more LEDs (rx and radio). (the FW claims it can support up to 16 LEDs, but I doubt that any vendor put more than 4 on a board) - update the LEDs in a _delayed_ workqueue. No one reported any more crashes. (see: "PATCH] p54: fix race condition in memory management") So we can stop burning the mm code. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Acked-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch rearrange and regroups most elements in p54_common. Signed-off-by: NChristian Lamparter <chunkeey@web.de> Acked-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Masakazu Mokuno 提交于
Update the MAINTAINERS entry for PS3 NETWORK SUPPORT. CC: Masakazu Mokuno <mokuno@sm.sony.co.jp> Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
Claiming every available 5 ghz channel has a couple of negative side-effects: scanning takes a long time, and the channel list overflows the available buffer space for netlink commands, resulting in: $ iw phy phy0 info command failed: No buffer space available (-105) This patch adds a modparam so people who want to see all the channels can do so by passing all_channels=1. By default users will see a smaller list of channels. This also halves scan time, from 10 seconds down to less than 5 when using world regulatory. Changes-licensed-under: 3-Clause-BSD Signed-off-by: NBob Copeland <me@bobcopeland.com> Reported-by: NSimon Farnsworth <simon@farnz.org.uk> Tested-By: NSimon Farnsworth <simon@farnz.org.uk> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-