ether_setup sets IFF_TX_SKB_SHARING but this is not supported by gre
as it modifies the skb on xmit.

Also, clean up whitespace in ipgre_tap_setup when we're already touching it.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
geneve as it modifies the skb on xmit.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ether_setup sets IFF_TX_SKB_SHARING but this is not supported by vxlan
as it modifies the skb on xmit.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calculate the maximum MTU taking into account the size of headers
involved in GENEVE encapsulation, as for other tunnel types.

Changes in v3:
- Correct comment style
Changes in v2:
- Conform more closely to ip_tunnel_change_mtu
- Exclude GENEVE options from max MTU calculation
Signed-off-by: NDavid Wragg <david@weave.works>
Acked-by: NJesse Gross <jesse@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ilya reported following lockdep splat:

kernel: =========================
kernel: [ BUG: held lock freed! ]
kernel: 4.5.0-rc1-ceph-00026-g5e0a311 #1 Not tainted
kernel: -------------------------
kernel: swapper/5/0 is freeing memory
ffff880035c9d200-ffff880035c9dbff, with a lock still held there!
kernel: (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0
kernel: 4 locks held by swapper/5/0:
kernel: #0:  (rcu_read_lock){......}, at: [<ffffffff8169ef6b>]
netif_receive_skb_internal+0x4b/0x1f0
kernel: #1:  (rcu_read_lock){......}, at: [<ffffffff816e977f>]
ip_local_deliver_finish+0x3f/0x380
kernel: #2:  (slock-AF_INET){+.-...}, at: [<ffffffff81685ffb>]
sk_clone_lock+0x19b/0x440
kernel: #3:  (&(&queue->rskq_lock)->rlock){+.-...}, at:
[<ffffffff816f6a88>] inet_csk_reqsk_queue_add+0x28/0xa0

To properly fix this issue, inet_csk_reqsk_queue_add() needs
to return to its callers if the child as been queued
into accept queue.

We also need to make sure listener is still there before
calling sk->sk_data_ready(), by holding a reference on it,
since the reference carried by the child can disappear as
soon as the child is put on accept queue.
Reported-by: NIlya Dryomov <idryomov@gmail.com>
Fixes: ebb516af ("tcp/dccp: fix race at listener dismantle phase")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.

Fix this issue by checking  and removing route cache when we get route.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

actions could change the etherproto in particular with ethernet
tunnelled data. Typically such actions, after peeling the outer header,
will ask for the packet to be  reclassified. We then need to restart
the classification with the new proto header.

Example setup used to catch this:
sudo tc qdisc add dev $ETH ingress
sudo $TC filter add dev $ETH parent ffff: pref 1 protocol 802.1Q \
u32 match u32 0 0 flowid 1:1 \
action  vlan pop reclassify

Fixes: 3b3ae880 ("net: sched: consolidate tc_classify{,_compat}")
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw fixes

Another bulk of fixes from Ido.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PVID is toggled off on a port member in a VLAN filtering bridge or
the PVID VLAN is deleted, make the port drop untagged packets. Reverse
the operation when PVID is toggled back on.

Set the PVID back to the default (1), when leaving the bridge so that
untagged traffic will be directed to the CPU.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VLAN filtering is enabled on a bridge and PVID is deleted from a
bridge port, then untagged frames are not allowed to ingress into the
bridge from this port.

Add the Switch Port Acceptable Frame Types (SPAFT) register, which
configures the frame admittance of the port.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For error handling, dma_alloc_coherent's return value
needs to be checked, not argument.
Signed-off-by: NInsu Yun <wuninsu@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
net: thunderx: Miscellaneous fixes

This patch series fixes couple of issues w.r.t multiqset mode
and receive packet statastics.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Counting rx packets for every CQE_RX in CQ irq handler is incorrect.
Synchronization is missing when multiple queues are receiving packets
simultaneously. Like transmit packet stats use HW stats here.

Also removed unused 'cqe_type' parameter in nicvf_rcv_pkt_handler().
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For secondary Qsets 'hw_tso' is not getting set as probe() returns
much earlier. Fixed it by moving silicon revision check.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a interface is assigned morethan 8 queues and the logical interface
is toggled i.e down & up, additional queues or qsets are not initialized
as secondary qset count is being set to zero while tearing down.
Signed-off-by: NSunil Goutham <sgoutham@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

crypto_alloc_hash never returns NULL
Signed-off-by: NInsu Yun <wuninsu@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With commit 0071f56e ("dsa: Register netdev before phy"), we are now trying
to free a network device that has been previously registered, and in case of
errors, this will make us hit the BUG_ON(dev->reg_state != NETREG_UNREGISTERED)
condition.

Fix this by adding a missing unregister_netdev() before free_netdev().

Fixes: 0071f56e ("dsa: Register netdev before phy")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the Marvell 88E1510, marvell_of_reg_init was called too late, in the
config_aneg function.
Since commit 113c74d8 ("net: phy: turn carrier off on phy attach"),
this lead to the link not coming up at boot anymore, due to the phy
state machine being stuck at waiting for interrupts (off by default on
the 88E1510).
For seven other Marvell PHYs, marvell_of_reg_init was not called at all.

Add a generic marvell_config_init function, which in turn calls
marvell_of_reg_init.
PHYs, which already have a specific config_init function with a call to
marvell_of_reg_init, are left untouched. The generic marvell_config_init
function is called for all the others, to get consistent behavior across
all Marvell PHYs.

Fixes: 113c74d8 ("net: phy: turn carrier off on phy attach")
Signed-off-by: NClemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop reference on the relay_po socket when __pppoe_xmit() succeeds.
This is already handled correctly in the error path.
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The example in the DT binding documentation uses the preliminary DT
bindings for the r8a7795 MSTP clocks, which never went upstream.
Update the example to use the DT bindings for the upstream Clock Pulse
Generator / Module Standby and Software Reset hardware block.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw fixes

Just a couple of fixes from Ido.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VLAN device leaves a bridge its STP state is set to DISABLED,
which causes the hardware to discard any packets coming through the port
with this VLAN.

Fix that by setting STP state to FORWARDING when the device leaves its
bridge and allow traffic to be directed to CPU.

Fixes: 26f0e7fb ("mlxsw: spectrum: Add support for VLAN devices bridging")
Reported-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MLXSW_PORT_MAX_PORTS represents the maximum number of local ports, which
is 65 for both ASICs (SwitchX-2 and Spectrum) supported by this driver.

Fixes: 93c1edb2 ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A previous commit (33f72e6f) added notification via netlink for tunnels
when created/modified/deleted. If the notification returned an error,
this error was returned from the tunnel function. If there were no
listeners, the error code ESRCH was returned, even though having no
listeners is not an error. Other calls to this and other similar
notification functions either ignore the error code, or filter ESRCH.
This patch checks for ESRCH and does not flag this as an error.
Reviewed-by: NHamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: NMark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw-phy-sel driver supports only MII, RMII, and RGMII PHY modes,
and silently handled any other values as if MII was specified. In a
case where the PHY mode was incorrectly specified, or a bug elsewhere,
there would be no indication of a problem. If MII was the correct mode,
then this will go unnoticed, otherwise the symptom will be a failure
to transmit/receive data over the RMII/RGMII link.

Add a dev_warn() to make this condition obvious and provide a
breadcrumb to follow.

Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid Rivshin <drivshin@allworx.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

genphy_config_init() masked out pause flags set in phy driver structure.
Pause flags needs to be preserved in phydev->supported &
phydev->advertising.
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Mellanox 10/40G mlx4 driver fixes for 4.5-rc

Bunch of fixes from the team to the mlx4 Eth and core drivers.

Series generated against net commit aac8d3c2 "qmi_wwan: add "4G LTE usb-modem U901""

Please push patches 1,2 and 6 to -stable  as well

changes from v0:
 - handled another wrongly accounted HW counter in patch #1 (Rick)
 - fixed coding style issues in patch #4 (Sergei)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.

Fixes: f4a1edd5 ('net/mlx4_en: Advertize encapsulation offloads [...]')
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

problem description:

The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.

solution:

Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.

Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.

Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.

Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.

Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PCI channel could go offline during reset due to EEH.  Don't bug on in
this case, the error is recoverable.

Fixes: f6bc11e4 ('net/mlx4_core: Enhance the catas flow to support device reset')
Signed-off-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error flow in procedure handle_existing_counter() is wrong.

The procedure should exit after encountering the error, not continue
as if everything is OK.

Fixes: 68230242 ('net/mlx4_core: Add port attribute when tracking counters')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.

Algorithm for shift value calculation:
 * Round up the maximal value in cycles to nearest power of two

 * Calculate maximal multiplier by division of all 64 bits set
   to above result

 * Then, invert the function clocksource_khz2mult() to get the shift from
   maximal mult value

Fixes: ec693d47 ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.

Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.

Fix that. Use it for rx_fifo_errors only.

Fixes: c27a02cd ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If tcp_v4_inbound_md5_hash() returns an error, we must release
the refcount on the request socket, not on the listener.

The bug was added for IPv4 only.

Fixes: 079096f1 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some cases where rtt_us derives from deltas of jiffies,
instead of using usec timestamps.

Since we want to track minimal rtt, better to assume a delta of 0 jiffie
might be in fact be very close to 1 jiffie.

It is kind of sad jiffies_to_usecs(1) calls a function instead of simply
using a constant.

Fixes: f6722583 ("tcp: track min RTT using windowed min-filter")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add new id (CONTEC C-NET(PC)C-100TX2)
Signed-off-by: NKen Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy has not been initialized, disconnecting it in the error
path results in a NULL pointer exception. Drop the phy_disconnect
from the error path.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Marvell 88E6240 has been tested successfully without further
changes. Add entry to the table of supported devices.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 52666986 ("tipc: let broadcast packet reception
use new link receive function") we introduced a new per-node
broadcast reception link instance. This link is created at the
moment the node itself is created. Unfortunately, the allocation
is done after the node instance has already been added to the node
lookup hash table. This creates a potential race condition, where
arriving broadcast packets are able to find and access the node
before it has been fully initialized, and before the above mentioned
link has been created. The result is occasional crashes in the function
tipc_bcast_rcv(), which is trying to access the not-yet existing link.

We fix this by deferring the addition of the node instance until after
it has been fully initialized in the function tipc_node_create().
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>