Adds support for controllers that use 64-byte contexts.  The following context
data structures are affected by this: Device, Input, Input Control, Endpoint,
and Slot.  To accommodate the use of either 32 or 64-byte contexts, a Device or
Input context can only be accessed through functions which look-up and return
pointers to their contained contexts.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure the xHCI output device context is 64-byte aligned.  Previous
code was using the same structure for both the output device context and
the input control context.  Since the structure had 32 bytes of flags
before the device context, the output device context wouldn't be 64-byte
aligned.  Define a new structure to use for the output device context and
clean up the debugging for these two structures.

The copy of the device context in the input control context does *not*
need to be 64-byte aligned.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allocates and initializes the scratchpad buffer array (XHCI 4.20).  This is an
array of 64-bit DMA addresses to scratch pages that the controller may use
during operation.  The number of pages is specified in the "Max Scratchpad
Buffers" field of HCSPARAMS2.  The DMA address of this array is written into
slot 0 of the DCBAA.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_parse_ss_endpoint_companion() was supposed to allocate a structure to
hold the SuperSpeed Endpoint Companion descriptor, and either copy the
values the device returned, or fill in default values if the device
descriptor did not include the companion descriptor.

However, the previous code would miss the last endpoint in a configuration
with no descriptors after it.  Make usb_parse_endpoint() allocate the SS
endpoint companion descriptor and fill it with default values, even if
we've run out of buffer space in this configuration descriptor.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor
parsing code.  It fails in some corner cases, which means ep->ss_ep_comp may be
NULL.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Pass back a babble error when this error code is seen in the transfer event TRB.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xHCI host controller can be programmed to retry a transfer a certain number
of times per endpoint before it passes back an error condition to the host
controller driver.  The xHC will return an error code when the error count
transitions from 1 to 0.  Programming an error count of 3 means the xHC tries
the transfer 3 times, programming it with a 1 means it tries to transfer once,
and programming it with 0 means the HW tries the transfer infinitely.

We want isochronous transfers to only be tried once, so set the error count to
one.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add more debugging to the irq handler, slot context initialization, ring
operations, URB cancellation, and MMIO writes.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Event Handler Busy bit in the event ring dequeue pointer is write 1 to
clear.  Fix the interrupt service routine to clear that bit after the
event handler has run.

xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer
without changing any of the four reserved bits in the lower nibble.  The event
handler busy (EHB) bit is write one to clear, so the new value must always
contain a zero in that bit in order to preserve the EHB value.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When there is a short packet on a control transfer, the xHCI host controller
hardware will generate two events.  The first event will be for the data stage
TD with a completion code for a short packet.  The second event will be for the
status stage with a successful completion code.  Before this patch, the xHCI
driver would giveback the short control URB when it received the event for the
data stage TD.  Then it would become confused when it saw a status stage event
for the endpoint for an URB it had already finished processing.

Change the xHCI host controller driver to wait for the status stage event when
it receives a short transfer completion code for a data stage TD.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are several xHCI data structures that use two 32-bit fields to
represent a 64-bit address.  Since some architectures don't support 64-bit
PCI writes, the fields need to be written in two 32-bit writes.  The xHCI
specification says that if a platform is incapable of generating 64-bit
writes, software must write the low 32-bits first, then the high 32-bits.
Hardware that supports 64-bit addressing will wait for the high 32-bit
write before reading the revised value, and hardware that only supports
32-bit writes will ignore the high 32-bit write.

Previous xHCI code represented 64-bit addresses with two u32 values.  This
lead to buggy code that would write the 32-bits in the wrong order, or
forget to write the upper 32-bits.  Change the two u32s to one u64 and
create a function call to write all 64-bit addresses in the proper order.
This new function could be modified in the future if all platforms support
64-bit writes.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xHCI functions to queue an URB onto the hardware rings must be called
with the xhci spinlock held.  Those functions will allocate memory, and
take a gfp_t memory flags argument.  We must pass them the GFP_ATOMIC
flag, since we don't want the memory allocation to attempt to sleep while
waiting for more memory to become available.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When an endpoint on a device under an xHCI host controller stalls, the
host controller driver must let the hardware know that the USB core has
successfully cleared the halt condition.  The HCD submits a Reset Endpoint
Command, which will clear the toggle bit for USB 2.0 devices, and set the
sequence number to zero for USB 3.0 devices.

The xHCI urb_enqueue will accept new URBs while the endpoint is halted,
and will queue them to the hardware rings.  However, the endpoint doorbell
will not be rung until the Reset Endpoint Command completes.

Don't queue a reset endpoint command for root hubs.  khubd clears halt
conditions on the roothub during the initialization process, but the roothub
isn't a real device, so the xHCI host controller doesn't need to know about the
cleared halt.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The 0.95 xHCI specification requires software to set the "TD size" field
in each transaction request block (TRB).  This field gives the host
controller an indication of how much data is remaining in the TD
(including the buffer in the current TRB).  Set this field in bulk TRBs
and data stage TRBs for control transfers.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Without this change the loops won't start
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

THis patch (as1270) allows the usbtest module to be built even when
USB_DEVICEFS isn't configured.  Tests can be performed without
USB_DEVICEFS, using the /dev/bus/usb/*/* device files.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

INDEX register has to be set to '0' before reading
CONFIGDATA register which is only present in TI musb
platforms.

Currently the default register access mode is set to
FLAT_MODE thus INDEX register is not getting set
properly with musb_ep_select() which is just a nop
operation in FLAT_MODE.This invalid register read is
causing module reinset failure.

Fixing the issue by moving INDEX register write part to
musb_read_configdata() function itself.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG.
Make sure any reference to it is also under the same #ifdef.

Without this fix, the driver failes to compile when USB_OTG is defined
but USB_MUSB_OTG isn't.
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This function uses wrong bit mask to prevent clearing RXCSR status
bits when halting an endpoint -- which results in clearing SentStall
and RxPktRdy bits (that the code actually tries to avoid); must be
a result of cut-and-paste...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added support for the Alcatel X060S/X200 broadband modems to the option
driver. The device starts in cd-rom emulation mode (1bbb:f000) and
requires the use of the usb_modeswitch tool to switch it to modem mode
(1bbb:0000).
Signed-off-by: NJavier Martin <jmartinj@iname.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPeng Huang <shawn.p.huang@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've opened up the case, and the chips in the ATEN UC2324 are:

Moschip
MCS7840CV-AA
69507-6B1
0650
(USB to 4-port serial)

(logo with AF kerned together)  0748  
24BC02  
SINGLP
(unknown 8-pin chip)

(logo looks like 3 or Z in circle)
ZT3243LEEA    0752
B7A16420.T
(4 chips, so this will be RS232 line driver)
(Probably equivalent of Sipex SP3243)

So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840,
and should use the mos7840.c driver.  I expect you will remove the
aten2011.c driver from the staging area.

From the aten2011.c source code, the device ID for the UC2322 (2 port
serial) is 0x7820, just like the Moschip evaluation board.  This value
should be added to the device id table of mos7840.c.

Here's a patch that adds these devices to the driver.


From: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

BugLink: https://bugs.launchpad.net/bugs/365291Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.

These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Ming Zhao <zhao.ming9@zte.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed that USB initialization didn't setup correctly on my kirkwood
based board (OpenRD base) if I hadn't initialized USB in U-boot first.
The error message looks like this:

  ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  orion-ehci orion-ehci.0: Marvell Orion EHCI
  orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
  orion-ehci orion-ehci.0: can't setup
  orion-ehci orion-ehci.0: USB bus 1 deregistered
  orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110
  orion-ehci: probe of orion-ehci.0 failed with error -110

which is caused by ehci_halt() timing out in the handshake() call. I
noticed that U-boot does a reset before calling handshake(), so this
patch does the same thing for Linux. USB now works for me.
Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: NVille Sundberg <vsundber@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OMAP: OHCI: hc_driver's stop method should call ohci_stop

Without this, the ohci-omap driver will not cleanup the debugfs
nodes when the driver is unloaded. So the next insmod will fail,
if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected.
Reported-by: Nvikram pandita <vikram.pandita@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Requests to get max LUN, for certain USB storage devices, require a
longer timeout before a correct reply is returned. This happens for a
Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set
to 0, thus losing functionality, because of the timeout occurring too
quickly.

Raising the timeout value fixes the issue and might help other devices
to return a correct max LUN value as well.
Signed-off-by: NGiacomo Lozito <james@develia.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is needed for compilation without CONFIG_PM.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After commit f092c240 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:

drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'

So I removed it.
Signed-off-by: NCarlos R. Mafra <crmafra@aei.mpg.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Those definitions are already provided by asm-generic
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes
- locking bug that was hidden by ecc2e05e
- Regression #13821
- Spurious warning when closing and blocking for data write out

With these changes my PL2303 always ends up as ttyUSB0 when it should and
the module refcounts stay correct.

I'll do a more wholesale split & tidy of _open in the next release or two
as we get a standard tty_port_open and port->ops->init port->ops->shutdown
call backs.

Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the
reports but it passes local testing with the same hardware as Alan Stern.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  inotify: use GFP_NOFS under potential memory pressure
  fsnotify: fix inotify tail drop check with path entries
  inotify: check filename before dropping repeat events
  fsnotify: use def_bool in kconfig instead of letting the user choose
  inotify: fix error paths in inotify_update_watch
  inotify: do not leak inode marks in inotify_add_watch
  inotify: drop user watch count when a watch is removed

This also makes close stall in the normal case which is apparently
needed to fix emacs
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
  cnic: Fix ISCSI_KEVENT_IF_DOWN message handling.
  net: irda: init spinlock after memcpy
  ixgbe: fix for 82599 errata marking UDP checksum errors
  r8169: WakeOnLan fix for the 8168
  netxen: reset ring consumer during cleanup
  net/bridge: use kobject_put to release kobject in br_add_if error path
  smc91x.h: add config for Nomadik evaluation kit
  NET: ROSE: Don't use static buffer.
  eepro: Read buffer overflow
  tokenring: Read buffer overflow
  at1700: Read buffer overflow
  fealnx: Write outside array bounds
  ixgbe: remove unnecessary call to device_init_wakeup
  ixgbe: Don't priority tag control frames in DCB mode
  ixgbe: Enable FCoE offload when DCB is enabled for 82599
  net: Rework mdio-ofgpio driver to use of_mdio infrastructure
  register at91_ether using platform_driver_probe
  skge: Enable WoL by default if supported
  net: KS8851 needs to depend on MII
  be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  amd64_edac: read the right F2 maskoffset reg

The port lock is used to protect the port state. However the port structure
is freed on a hangup, then the lock taken on a close. The right fix is to
drop the port on tty->shutdown() but we can't yet do that due to sleep v
non-sleeping rules. Instead do the next best thing and fix it up when we are
not in -rc season.
Reported-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Tested-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>