Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that all VSIs are configured to receive broadcasts as default, we
don't need to add a filter. This eliminates an annoying but harmless
error message each time VFs are created or reset.

Change-ID: I4cd6339684df45b0d2722133eeb84c14fa93ea19
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This logic is inverted. If the RXHASH flag is set, then we should go
ahead and call skb_set_hash.

Change-ID: Ib2e30356dced1d3e939c8061ab6ad5bd94197e7c
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For the SR-IOV VSIs, when the queue filtering section is valid,
the RSS LUT needs to be set to use the VSI specific lookup table
(otherwise it will use the PF RSS LUT table).

Change-ID: Ia9377cc818078238a75c3bdeade1b593a91b3480
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects Rx ptype payload layer for non_tunneled ipv6. It
should be layer 4 for UDP, instead of layer 3.

Change-ID: I9382e4458ab3c4e58f6d2e9f195d5d4ee513805e
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use WARN_ONCE in order to highlight the issue, but don't display
a warning every time. The user should be able to see the ethtool counter
we created if necessary to see how often it is occurring.

Change-ID: I40c4ea159819b64a7d33b7f5716749089791533a
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were only looking at the FW supported PHY types if link
was down, because we want to be more specific when link is up. This
refactor changes this. When link is down, we still rely on the FW
supported PHY types, but when link is up, we select the possible
supported link modes from what we know about the current PHY type, and
AND that with the FW supported PHY types.

Change-ID: Ice5dad83f2a17932b0b8b59f07439696ad6aa013
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If an untrusted VF attempts to configure promiscuous mode, log a message
pointing out its naughty behavior. But then, instead of returning an
error to the offender, just lie to it and say everything's OK. It will
continue on its way, thinking it's in promiscuous mode, but receiving no
packets except its own.

Change-ID: I63369215b1720f3c531eedfc06af86ff8c0e3dc8
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.

The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.

For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.

Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP                    : off
LinkPolling            : off
flow-director-atr      : on
veb-stats              : off
hw-atr-eviction        : off
vf-true-promisc-support: off

to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on

At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic

Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the support code for calling the AdminQ API call aq_set_switch_config
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables a feature to enable/disable all multicast
for a trusted VF.

Change-Id: I926eba7f8850c8d40f8ad7e08bbe4056bbd3985f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add flag to tell firmware to disable link on all ports.

This patch changes the bits set for telling firmware the PHY needs
to be modified by driver.  Without this patch, the setting will only
set that mode for the current port on the device.  Because the
MDIO interface is common for the copper device. The command needs to
set the mode for all ports.

Change-ID: I8baa7da91d384291ac95b41ae1a516604f8eb67f
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2016-05-13

This series contains updates to e1000e, igb and igbvf.

Steve Shih fixes an issue for disabling auto-negotiation and forcing
speed and duplex settings for non-copper media.

Brian Walsh cleanups some inconsistency in the use of return variables
names to avoid confusion.

Jake cleans up the drivers to use the BIT() macro when it can, which will
future proof the drivers for GCC 6 when it gets released.  Cleaned up
dead code which was never being used.  Also fixed e1000e, where it was
incorrectly restting the SYSTIM registers every time the ioctl was being
run.

Denys Vlasenko fixes an oversight where incvalue variable holds a 32
bit value so we should declare it as such, instead of 64 bits.  Also
fixed an overflow check, where two reads are the same, then it is not
an overflow.

Nathan Sullivan fixes the PTP timestamps for transmit and receive
latency based on the current link speed.

Alexander Duyck adds support for partial GSO segmentation in the case
of tunnels for igb and igbvf.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.

Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.

In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.
Reported-by: NBrian Walsh <brian@walsh.ws>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NBrian Walsh <brian@walsh.ws>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for partial GSO segmentation in the case of
tunnels.  Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header.  This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The E1000_ICH_NVM_SIG_MASK value is shifted, out to the 31st bit, which
is the signed bit for signed constants. Mark these values as unsigned to
prevent compiler warnings and issues on platforms which a different
signed bit implementation.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.

Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To prevent signed bitshift issues, and improve code readability, use the
BIT() macro. Also make use of GENMASK or the unsigned postfix where this
is more appropriate than BIT()
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable rdlen is set but never used, and thus setting it is dead
code. Remove it.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports.  To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: NNathan Sullivan <nathan.sullivan@ni.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]

er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.

If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.

We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.

Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If two consecutive reads of the counter are the same, it is also
not an overflow.  "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".

Before the patch, we could perform an *erroneous* correction:

Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.

Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.

Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: NBrian Walsh <brian@walsh.ws>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.

For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.

e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.

Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: NSteve Shih <sshih@cisco.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While testing an OpenStack configuration using VXLANs I saw the following
call trace:

 RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
 RSP: 0018:ffff88103867bc50  EFLAGS: 00010286
 RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
 RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
 RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
 R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
 R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
 FS:  0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
 Stack:
  ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
  ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
  ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
 Call Trace:
  [<ffffffff81576515>] ? skb_checksum+0x35/0x50
  [<ffffffff815733c0>] ? skb_push+0x40/0x40
  [<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
  [<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
  [<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
  [<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
  [<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
  [<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
  [<ffffffff815899d0>] net_rx_action+0x160/0x380
  [<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
  [<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
  [<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
  [<ffffffff8109a400>] ? sort_range+0x30/0x30
  [<ffffffff81096da8>] kthread+0xd8/0xf0
  [<ffffffff81693c82>] ret_from_fork+0x22/0x40
  [<ffffffff81096cd0>] ? kthread_park+0x60/0x60

The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel.  I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.

To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev.  This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated.  In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.

Fixes: 63058308 ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sunrpc is using SOCKWQ_ASYNC_NOSPACE without setting SOCK_FASYNC,
so the recent optimizations done in sk_set_bit() and sk_clear_bit()
broke it.

There is still the risk that a subsequent sock_fasync() call
would clear SOCK_FASYNC, but sunrpc does not use this yet.

Fixes: 9317bb69 ("net: SOCKWQ_ASYNC_NOSPACE optimizations")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NJiri Pirko <jiri@resnulli.us>
Reported-by: NHuang, Ying <ying.huang@intel.com>
Tested-by: NJiri Pirko <jiri@resnulli.us>
Tested-by: NHuang, Ying <ying.huang@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an ACTIVATE or data packet is received in a link in state
ESTABLISHING, the link does not immediately change state to
ESTABLISHED, but does instead return a LINK_UP event to the caller,
which will execute the state change in a different lock context.

This non-atomic approach incurs a low risk that we may have two
LINK_UP events pending simultaneously for the same link, resulting
in the final part of the setup procedure being executed twice. The
only potential harm caused by this it that we may see two LINK_UP
events issued to subsribers of the topology server, something that
may cause confusion.

This commit eliminates this risk by checking if the link is already
up before proceeding with the second half of the setup.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for
better readability.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not include attribute IFLA_GRE_TOS.
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a netns leak.

Fixes: 93edb8c7 ("gtp: reload GTPv1 header after pskb_may_pull()")
Reported-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Some more work for 4.7, notably:
 * completion and fixups of nla_put_64_64bit() work
 * remove a/b/g/n from wext nickname to avoid confusion
   with 11ac (which wouldn't even fit fully there due to
   string length restrictions)

along with some other minor changes/cleanups.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.

In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.

To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The devlist_mtx mutex was removed about two years ago, in favour of just
using RTNL/RCU protection. Remove the comment still referencing it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows finding vendor IE from a specific vendor.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack.  Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>