This patch adds cuboot support for MPC7448HPC2 platform.
The cuImage can be used with legacy u-boot without FDT support.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. PCI and reset are factored out into pq2.c.  I renamed them from m82xx
to pq2 because they won't work on the Integrated Host Processor line of
82xx chips (i.e. 8240, 8245, and such).

2. The PCI PIC, which is nominally board-specific, is used on multiple
boards, and thus is used into pq2ads-pci-pic.c.

3. The new CPM binding is used.

4. General cleanup.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

It now uses the new CPM binding and the generic pin/clock functions, and
has assorted fixes and cleanup.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The localbus node is used to describe devices that are connected via a chip
select or similar mechanism.  The advantages over placing the devices under
the root node are that it can be probed without probing other random things
under the root, and that the description of which chip select a given device
uses can be used to set up mappings if the firmware failed to do so in a
useful manner.

cuboot-pq2 is updated to match the binding; previously, it called itself
chipselect rather than localbus, and used phandle linkage between the
actual bus node and the control node (the current agreement is to simply use
the fully-qualified address of the control registers, and ignore the overlap
with the IMMR node).
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is just a rename patch; internal references to mpc82xx_ads will be
changed in the next one.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

m82xx_calibrate_decr(), mpc82xx_ads_show_cpuinfo(), and mpc82xx_halt() do
anything useful beyond what the generic code does.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The 8272 (and presumably other PCI PQ2 chips) appear to have the
same issue as the 83xx regarding PCI streaming DMA.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This provides a generic way for board code to set up CPM pins, rather
than directly poking magic values into registers.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Mostly sparse fixes (__iomem annotations, etc); also, cpm2_immr
is used rather than creating many temporary mappings.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The 8xx can only support a max of 8M during early boot (it seems a lot of
8xx boards only have 8M so the bug was never triggered), but the early
allocator isn't aware of this.  The following change makes it able to run
with larger memory.
Signed-off-by: NJohn Traill <john.traill@freescale.com>
Signed-off-by: NVitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The CPU15 erratum on MPC8xx chips can cause incorrect code execution
under certain circumstances, where there is a conditional or indirect
branch in the last word of a page, with a target in the last cache line
of the next page.  This patch implements one of the suggested
workarounds, by forcing a TLB miss whenever execution crosses a page
boundary.  This is done by invalidating the pages before and after the
one being loaded into the TLB in the ITLB miss handler.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

These let board code set up pins and clocks without having to
put magic numbers directly into the registers.

The clock function is mostly duplicated from the cpm2 version;
hopefully this stuff can be merged at some point.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. Keep a global mpc8xx_immr mapping, rather than constantly
creating temporary mappings.
2. Look for new fsl,cpm1 and fsl,cpm1-pic names.
3. Always reset the CPM when not using the udbg console;
this is required in case the firmware initialized a device
that is incompatible with one that the kernel is about to
use.
4. Remove some superfluous casts and header includes.
5. Change a usage of IMAP_ADDR to get_immrbase().
6. Use phys_addr_t, not uint, for dpram_pbase.
7. Various sparse-related fixes, such as __iomem annotations.
8. Remove mpc8xx_show_cpuinfo, which doesn't provide anything
useful beyond the generic cpuinfo handler.
9. Move prototypes for 8xx support functions from board files
to sysdev/commproc.h.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. Move CONSISTENT_START on 8xx so that it doesn't overlap the IMMR mapping.
2. The wrong register was being loaded into SPRN_MD_RPN.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This prevents some bootloader/bootwrapper characters from being lost.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Mostly a bunch of direct access to in/out conversions, plus a few
cast removals, __iomem annotations, and miscellaneous cleanup.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The existing OF glue code was crufty and broken.  Rather than fix it,
it has been removed, and the serial driver now talks to the device tree
directly.

The non-CONFIG_PPC_CPM_NEW_BINDING code can go away once CPM platforms
are dropped from arch/ppc (which will hopefully be soon), and existing
arch/powerpc boards that I wasn't able to test on for this patchset get
converted (which should be even sooner).
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

fsl_get_immr() uses /soc/ranges to determine the immr.

mpc885_get_clock() transforms a crystal frequency into a system frequency
according to the PLL register settings.

pq2_get_clocks() does the same as the above for the PowerQUICC II,
except that it produces several different clocks.

The mpc8xx/pq2 set_clocks() functions modify common properties in
the device tree based on the given clock data.

The mpc885/pq2 fixup_clocks() functions call get_clocks(), and
pass the results to set_clocks().
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Consensus was reached to put PCI nodes at the root of the tree (and not
under /soc), but the phandle to a control node was rejected in favor of
simply not worrying about /pci/reg overlapping /soc/ranges.

This updates cuboot-82xx to not look for the phandle.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This code assumes that the ports have been previously set up, with
buffers in DPRAM.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This introduces a new device binding for the CPM and other devices on
these boards.  Some of the changes include:

1. Proper namespace scoping for Freescale compatibles and properties.

2. Use compatible rather than things like device_type and model
to determine which particular variant of a device is present.

3. Give the drivers the relevant CPM command word directly, rather than
requiring it to have a lookup table based on device-id, SCC v. SMC, and
CPM version.

4. Specify the CPCR and the usable DPRAM region in the CPM's reg property.

Boards that do not require the legacy bindings should select
CONFIG_PPC_CPM_NEW_BINDING to enable the of_platform CPM devices. Once
all existing boards are converted and tested, the config option can
become default y to prevent new boards from using the old model.  Once
arch/ppc is gone, the config option can be removed altogether.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

As suggested by David Gibson, now that we have a separate node
for the baud rate generators, it's better to use the standard
clock-frequency property than a cpm-node-level fsl,brg-frequency
property.

This patch updates existing places where fsl,brg-frequency is
used.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Commit 8112753b made 44x in
ARCH=powerpc builds use cpu setup routines in cpu_setup_44x.S,
but didn't make a similar change for ARCH=ppc, and consequently
the ARCH=ppc builds fail with undefined symbols (since both use
the same cputable.c).

This fixes it by including cpu_setup_44x.S in the ARCH=ppc builds,
and by taking out the now-redundant FPU initialization in
arch/ppc/kernel/head_44x.S.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Reverts commit a15da8ef

This driver is used by devices other than the xilinx opb-uartlite which
depend on bytewise access to the registers.  The change to 32 bit access
does not work on these devices.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add macros to define register names to improve readability.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This simply adds the boilerplate default Ethernet address to embed_config
for the Xilinx platform (bug fix).
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

XilnixFB can be used by more than just arch/ppc.  Move the data structure
definition into include/linux/xilinxfb.h so it can be used by microblaze
and arch/powerpc
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Flush the uartlite RX fifo so that characters typed before entry into
the zImage wrapper do not muck up the kernel command line.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Tell git to ignore the generated treeImage.* files in arch/powerpc/boot
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

By configuring it earlier we get console output sooner which is helpful
for debugging when the kernel crashes before the serial drivers are
initialized.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add of_platform bus binding so this driver can be used with arch/powerpc
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Tidy the comments to split the driver into logical section; the main driver,
the console driver, the platform bus binding, and module initialization
and teardown.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Separate the bus binding code from the driver structure allocation code in
preparation for adding the of_platform_bus bindings needed by arch/powerpc
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Changed to make the following OF_platform bus binding patch a wee bit cleaner
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Changed to match naming convention used in the rest of the module
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>