Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove cp210x_disconnect which is used to kill traffic although this is
already handled by the generic framework.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is no need to initialise the read urb as this is done at port
probe.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Export usb_serial_generic_close so that drivers can easily kill the read
and write urb and make sure that the write fifo is reset.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The cp210x requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Increase the bulk-out buffer size from 64 to 256 byte.

This gives a significant increase in throughput already at 1Mbaud
(e.g. 710 instead of 640 KB/s) as well as lowered CPU usage.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: NMichael Brunner <mibru@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As reported in
http://bugzilla.kernel.org/show_bug.cgi?id=10980Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

#define dbg adds the newline, messages shouldn't.
Converted dbg("%s", "some string") to dbg("some string")
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.

The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
	struct I1 {
	  ...
	  const struct I2 *x;
	  ...
	};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
	struct I1 y = {
	  .x = E,
	};
@c@
identifier r.I2;
identifier s.E;
@@
	const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+	const
	struct I2 E[] = ...;
// </smpl>
Signed-off-by: NNémeth Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2

9a68e39d broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.

Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Reported-by: NKarl Hiramoto <karl@hiramoto.org>
Tested-by: NKarl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the Dell inspiron mini 10, the GPS is connected via a cp2102. This patch
adds detection of this USB device. (I haven't managed to use the GPS under
Linux yet, though)
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These are handled by the tty_port core code which will raise and lower the
carrier correctly in tty_wait_until_ready
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As reported by David Potts from Arkham Technology, the current driver
works with their hardware on addition of the device ids.
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1254) splits up the shutdown method of usb_serial_driver
into a disconnect and a release method.

The problem is that the usb-serial core was calling shutdown during
disconnect handling, but drivers didn't expect it to be called until
after all the open file references had been closed.  The result was an
oops when the close method tried to use memory that had been
deallocated by shutdown.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch replaces the string "CP2101" with "CP210x" within cp210x.c
This is to reduce confusion about the fact that the driver is actually
compatible with CP2101, CP2102 and CP2103 devices.
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>

(Fixed some collisions merging)
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The CP210X driver was developed without official device specifications.
This has lead to an incorrect assumption that all GET request codes are
equal to the corresponding SET request code +1.
This patch removes this incorrect assumption, and uses request code
definitions based on the updated GPL driver from SiLabs.
This modification is needed before extended functionality such as GPIO
on CP2103 can be supported.
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is really a follow up to the modifications Alan Cox made for commit
95da310e to pass a tty_struct to various
interface functions, which broke the serial configuration (termios) functions
when the device is being used as a console. These changes restore the
configuration to proper functioning both as a tty and as a console.  As Alan
notes in that commit, these changes will need to be tweaked when we have
a proper console abstraction.
Signed-off-by: NDavid VomLehn <dvomlehn@cisco.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

One new device ID for CP2101 driver.

Signed-off-by: Alex Stephens alex@miranova.com

Lots of users are getting confused about the cp2101 driver.  It really
does support more than just the cp2101 device, so rename it to cp210x to
try to prevent confusion.

Cc: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch lowers the logging priority of certain messages to prevent
users from flooding the log files.
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the extended range of baud rates supported
by CP2102 and CP2103 devices described in SiLabs AN205.  An additional
function cp2101_quantise_baudrate rounds the baud rate as per AN205
Table 1.  A modification to the baud rate calculation removes a rounding
error, allowing the full range of baud rates to be used.
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Robert M. Kenney <rmk@unh.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,

PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c

From: Tomasz K <eros81@o2.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the vendor/product ID of the fasttrax GPS evaluation kit from:
	http://www.fastraxgps.com/products/evaluationtools/evaluationkit/

to the cp2101 module since this device is actually equipped with a
CP210x USB to serial bridge.

The vendor/product ID is: 0x10c4/0x826b.
Signed-off-by: NWolfgang Glas <wolfgang.glas@ev-i.at>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch which adds IDs for AKTAKOM USB->RS232 cable
(http://www.aktakom.ru/product/kio/ace-1001.htm) is attached.

From: M Kondrin <mkondrin@hppi.troitsk.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Enfora GSM2228 based on Cygnal Integrated Products chip uses the same
cp2101 driver.
Signed-off-by: NDamir N Abdullin <damir@mimas.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the device vendor and product IDs for Amber Wireless AMB2560
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Bring up to coding style
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.

So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.

Longer term we need a proper tty as console abstraction
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The get/set 2101_config helpers take an unsigned int rather than an
int.  It is safe to change these in each case and may even produce
better code as it will be an unsigned divide rather than a signed
divide in places.  All other manipulation was setting/masking bits
which will not be affected by the sign change.

Fixes the following sparse warnings:
drivers/usb/serial/cp2101.c:378:44: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:378:44:    expected unsigned int *data
drivers/usb/serial/cp2101.c:378:44:    got int *<noident>
drivers/usb/serial/cp2101.c:388:40: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:388:40:    expected unsigned int *data
drivers/usb/serial/cp2101.c:388:40:    got int *<noident>
drivers/usb/serial/cp2101.c:413:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:413:42:    expected unsigned int *data
drivers/usb/serial/cp2101.c:413:42:    got int *<noident>
drivers/usb/serial/cp2101.c:421:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:421:42:    expected unsigned int *data
drivers/usb/serial/cp2101.c:421:42:    got int *<noident>
drivers/usb/serial/cp2101.c:444:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:444:42:    expected unsigned int *data
drivers/usb/serial/cp2101.c:444:42:    got int *<noident>
drivers/usb/serial/cp2101.c:451:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:451:42:    expected unsigned int *data
drivers/usb/serial/cp2101.c:451:42:    got int *<noident>
drivers/usb/serial/cp2101.c:458:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:458:42:    expected unsigned int *data
drivers/usb/serial/cp2101.c:458:42:    got int *<noident>
drivers/usb/serial/cp2101.c:471:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:471:42:    expected unsigned int *data
drivers/usb/serial/cp2101.c:471:42:    got int *<noident>
drivers/usb/serial/cp2101.c:481:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:481:42:    expected unsigned int *data
drivers/usb/serial/cp2101.c:481:42:    got int *<noident>
drivers/usb/serial/cp2101.c:561:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:561:41:    expected unsigned int *data
drivers/usb/serial/cp2101.c:561:41:    got int *<noident>
drivers/usb/serial/cp2101.c:591:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:591:45:    expected unsigned int *data
drivers/usb/serial/cp2101.c:591:45:    got int *<noident>
drivers/usb/serial/cp2101.c:597:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:597:41:    expected unsigned int *data
drivers/usb/serial/cp2101.c:597:41:    got int *<noident>
drivers/usb/serial/cp2101.c:608:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:608:45:    expected unsigned int *data
drivers/usb/serial/cp2101.c:608:45:    got int *<noident>
drivers/usb/serial/cp2101.c:614:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:614:41:    expected unsigned int *data
drivers/usb/serial/cp2101.c:614:41:    got int *<noident>
drivers/usb/serial/cp2101.c:623:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:623:45:    expected unsigned int *data
drivers/usb/serial/cp2101.c:623:45:    got int *<noident>
drivers/usb/serial/cp2101.c:680:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:680:50:    expected unsigned int *data
drivers/usb/serial/cp2101.c:680:50:    got int *<noident>
drivers/usb/serial/cp2101.c:690:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:690:43:    expected unsigned int *data
drivers/usb/serial/cp2101.c:690:43:    got int *<noident>
drivers/usb/serial/cp2101.c:715:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:715:41:    expected unsigned int *data
drivers/usb/serial/cp2101.c:715:41:    got int *<noident>
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ThinkOptics WavIt to cp2101 device table
Signed-off-by: NBernhard Beck <kernel@goodcoffee.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb-serial core no longer checks these fields so remove them from
all of the individual drivers.  They will be removed from the usb-serial
core in a patch later in the series.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>