- 25 4月, 2008 40 次提交
-
-
由 Alan Cox 提交于
- If a termios change fails due to lack of memory we should copy the old settings back over as the device has not changed - Note various locking problems - kl5kusb105 had various remaining tty flag handling problems - Make safe_serial use tty_insert_flip_string not open coded loops - set termios speed properly in usb_serial Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Harvey Harrison 提交于
__FUNCTION__ is gcc-specific, use __func__ Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1079) cleans up the way URB_* flags are exported in usbfs. The URB_NO_INTERRUPT flag is now exported (this is the only behavioral change). USBDEVFS_URB_* macros are added for URB_NO_FSBR, URB_ZERO_PACKET, and URB_NO_INTERRUPT, making explicit the fact that the kernel accepts them. The flag matching takes into account that the URB_* values may change as the kernel evolves, whereas the USBDEVFS_URB_* values must remain fixed since they are a user API. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1072) fixes some recently-introduced compile problems that show up in ehci-hcd when CONFIG_PM is turned off. PORT_WAKE_BITS needs to be defined always. ehci_port_power() is called during initialization by all the EHCI variants other than the PCI version, in which it is "defined but not used". So add a call to it. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Brownell 提交于
Simplify processing of completed qtds, and correct handling of short reads, by removing two state variables: - "qtd_status" wasn't needed. The current URB's status is either OK (-EINPROGRESS) or some fault status. Once a fault appears, the queue halts and any later QTDs are immediately removed, so no temporary status is needed. (Or for typical short reads, it's not treated as a fault, so no queue halt is needed.) - "do_status" was erroneous. Because of how the queue is set up, short control reads can (and should!) be treated like full size reads, and cleaned up the usual way. The status stage will be executed transparently, and usbcore handles the choice of whether to report this status as unexected. The "do_status" problem caused a rather perplexing timing-dependent problem with usbtest case 10. Sometimes it would make the controller skip a dozen transactions while (wrongly) trying to clean up after a short transfer. Fortunately, removing a dcache contention issue made this become trivial to reproduce (on one test rig), so enough clues finally presented themselves ... I think this has been around for a very long time, but was worsened by recent urb->status changes. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Brownell 提交于
Fix bogus assignment of "unsigned char *" to "char *": preserve unsignedness. These values are used directly as descriptor lengths when iterating through the buffer, so this *could* cause oddness that potentially includes oopsing. (IMO not likely, except as part of a malicious device...) Fix the bogus warning in CDC ACM which highlighted this problem (by showing a negative descriptor type). It uses the undesirable legacy err() for something that's not even an error; switch to use dev_dbg, and show descriptor types in hex notation to match the convention for such codes. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Acked-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
Add Documentation about callbacks in USB. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1069b) changes the way OHCI root-hub status-change interrupts are enabled. Currently a special HCD method, hub_irq_enable(), is called when the hub driver is finished using a root hub. This approach turns out to be subject to races, resulting in unnecessary polling. The patch does away with the method entirely. Instead, the driver automatically enables the RHSC interrupt when no more status changes are present. This scheme is safe with controllers using level-triggered semantics for their interrupt flags. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1068b) disables the RD interrupt flag when an OHCI root hub is suspended with remote wakeup disabled. Although the spec clearly states that this flag permits the controller to issue an interrupt when a resume request from downstream is detected and not when a local status change occurs, some controllers mistakenly use it for both types of event. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
When a USB device is suspended, whether or not it is enabled for remote wakeup depends on the device_may_wakeup() setting. The setting is then saved in the do_remote_wakeup flag. Later on, however, the device_may_wakeup() value can change because of user activity. So when testing whether a suspended device is or should be enabled for remote wakeup, we should always test do_remote_wakeup instead of device_may_wakeup(). This patch (as1076) makes that change for root hubs in several places. The patch also adjusts uhci-hcd so that when an autostopped controller is suspended, the remote wakeup setting agrees with the value recorded in the root hub's do_remote_wakeup flag. And the patch adjusts ehci-hcd so that wakeup events on selectively suspended ports (i.e., the bus itself isn't suspended) don't turn on the PME# wakeup signal. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1061) makes g_file_storage more compliant with the Bulk-Only Transport specification. After an invalid CBW is received, the gadget must ignore any further bulk-OUT data until it is reset. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Greg Kroah-Hartman 提交于
Remove the unused check for num_interrupt and friends as well as remove them from the header file because no usb-serial drivers no longer reference them. Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Greg Kroah-Hartman 提交于
The usb-serial core no longer checks these fields so remove them from all of the individual drivers. They will be removed from the usb-serial core in a patch later in the series. Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Chris Collins 提交于
Setting DTR et al. should work for all interfaces if you actually pass the interface number. :-P This should help with devices that have important pseudo-serial ports that aren't on the first interface in the device. Signed-off-by: NChris Collins <chris@ursys.com.au> Signed-off-by: NMatthias Urlichs <matthias@urlichs.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
This adds documentation about the new usb anchor infrastructure. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Brownell 提交于
Provide better comments about qh_completions() and QTD handling. That code can be *VERY* confusing, since it's evolved over a few years to cope with both hardware races and silicon quirks. Remove two unlikely() annotations that match the GCC defaults (and are thus pointless); add an "else" to highlight code flow. This patch doesn't change driver behavior. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1077) logs an error message whenever the kernel is unable to enumerate a new USB device. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
Comments here are so outdated that they are plain wrong. We cannot expect people to write correct drivers if the headers have incorrect comments. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Robert P. J. Day 提交于
Given that most of drivers/usb/serial/Kconfig is wrapped inside: if USB_SERIAL ... endif # USB_SERIAL remove the consequently redundant dependencies on USB_SERIAL. Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
This adds the ability to trigger asynchronous unlinks of anchored URBs. This is needed for error handling in the comntext of completion handlers, which cannot sleep. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yoshihiro Shimoda 提交于
R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can support SH7366 USB host by changing several R8A66597 code. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yoshihiro Shimoda 提交于
Fix the problem that enumeration of a USB device was slow. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yoshihiro Shimoda 提交于
This driver ignored the value of bInterval and revised the problem that performed interrupt transfer. ASIX USB Ethernet adapter comes to work with this host controller by applying this patch. Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Paulius Zaleckas 提交于
Removes unimplemented TCFLSH handling from oti6858, because it was preventing TCFLSH handling by upper layer (line discipline) drivers (see drivers/char/tty_io.c line 3450). Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt> Acked-by: NAlan Cox <alan@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sarah Sharp 提交于
This patch refactors some shutdown code so it can be shared between ehci_stop() and ehci_shutdown(). This also fixes a couple potential bugs: - ehci_shutdown() was not locking ehci->lock before halting the HC. - ehci_shutdown() didn't disable the watchdog and IAA timers. - ehci_stop() was resetting the host controller when it may have been running, which the EHCI spec says "may result in undefined behavior". ehci_stop() was calling port_power() to turn off the ports, which waited 20ms after applying the port change. The msleep was for the case where the HC might take 20ms to turn the ports on; since we're shutting them off, we can avoid the msleep and just use ehci_turn_off_ports(). ehci_stop() doesn't need to clear the intr_enable register or revert ownership of the companion controllers to the BIOS, because the host controller reset should have done that. There might be a buggy host controller that doesn't follow the reset rules, but for now we assume it's redundant code and remove it. [ A subsequent patch will cancel the timers later ... this version carries forward existing bugs where timers could get re-armed after they're canceled. ] Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Brownell 提交于
The at91sam9 chip are ARMv5 so they support preload instructions. Use preloading to load the FIFO a bit faster. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1075) changes dummy-hcd to dynamically allocate its platform_device structures, using the core platform_device_alloc() interface. This is what it should have done all along, because the dynamically-allocated structures have a release method in the driver core and are therefore immune to being released after the module has been unloaded. Thanks to Richard Purdie for pointing out the need for this change. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Brownell 提交于
Restore some section annotations: they were switched to "__devinit" while they should have been "__init", because of bogus warnings. The warnings are now fixed, so the runtime footprint of various drivers can now shrink a bit. On ARMv5, it's about 600 bytes except for the Ethernet gadget, where it can save a bit more. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
Removing an interface's sysfs files before unregistering the interface doesn't work properly, because usb_unbind_interface() will reinstall altsetting 0 and thereby create new sysfs files. This patch (as1074) removes the files after the unregistration is finished. It's not quite as clean, but at least it works. Also, there's no need to check if an interface has been registered before removing its sysfs files. If it hasn't been registered then the files won't have been created, so usb_remove_sysfs_intf_files() will simply do nothing. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Tested-by: NJiri Slaby <jirislaby@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Harvey Harrison 提交于
The kernel is written in C, not C++, use __func__ Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
Drivers in the ohci-hcd family should perform certain tasks whenever their controller device is resumed. These include checking for loss of power during suspend, turning on port power, and enabling interrupt requests. Until now these jobs have been carried out when the root hub is resumed, not when the controller is. Many drivers work around the resulting awkwardness by automatically resuming their root hub whenever the controller is resumed. But this is wasteful and unnecessary. To simplify the situation, this patch (as1066) adds a new core routine, ohci_finish_controller_resume(), which can be used by all the OHCI-variant drivers. They can call the new routine instead of resuming their root hubs. And ohci-pci.c can call it instead of using its own special-purpose handler. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
The .suspend and .resume method pointers in struct usb_hcd have not been fully understood by host-controller driver writers. They are meant for use with PCI controllers; other platform-specific drivers generally should not refer to them. To try and clarify matters, this patch (as1065) renames those methods to .pci_suspend and .pci_resume. It eliminates corresponding dead code and bogus references in the ohci-ssb and u132-hcd drivers. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
Currently EHCI root hubs enumerate with a bDeviceProtocol code indicating that they possess a Transaction Translator. However the vast majority of controllers do not; they rely on a companion controller to handle full- and low-speed communications. This patch (as1064) changes the root-hub device descriptor to match the actual situation. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
USB is moving to transfering status as a parameter. To ease the transition urb->status is to be touched only once in a function. The xpad driver has been overlooked. Dmitry wants this to go through the USB tree. Signed-off-by: NOliver Neukum <oneukum@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1063) fixes a bug in the way ohci-hcd resumes its controllers. It leaves the Master Interrupt Enable bit turned off. If the root hub is resumed immediately this won't matter. But if the root hub is suspended (say because no devices are plugged in), it won't ever wake up by itself. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ingo van Lil 提交于
Fix a messed up combination of two nested switch statements in drivers/usb/gadget/dummy_hcd.c. According to the USB spec (section 5.8.3) the maximum packet size for bulk endpoints can be 512 for high-speed devices and 8, 16, 32 or 64 for full-speed devices. Low-speed devices must not have bulk endpoints. Signed-off-by: NIngo van Lil <inguin@gmx.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jesper Juhl 提交于
In drivers/usb/gadget/amd5536udc.c::udc_pci_probe(), sizeof(struct udc) storage is allocated for 'dev'. There are many exit points from the function where 'dev' is not free'd but has also not yet been used for anything. The following patch free's 'dev' at the return points where it has not yet been used. Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1060) makes usb-storage set the DMA alignment mask for SCSI slaves to match the maxpacket size of the bulk-IN endpoint, rather than always setting it to 511. For full-speed devices that mask is too restrictive, and wireless USB devices can have maxpacket sizes larger than 512. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Craig W. Nadler 提交于
G_PRINTER: Bug fix for blocking reads and a fix for a memory leak. This fixes bugs in blocking IO calls. When the poll() entry point is called receive transfers will be setup if they have not already been. Another bug fix is that the poll() entry point now checks the current receive buffer for data when reporting if any data had been received. A memory leak was fixed that could have occurred when a USB reset happened. Signed-off-by: NCraig W. Nadler <craig@nadler.us> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jesper Juhl 提交于
platform_get_resource() may return null, so although it seems it will never do so here unless there's a bug elsewhere, it does no harm to be defensive and test. Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Acked-by: NMagnus Damm <magnus.damm@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-