Based on original patch from Shirley Ma <xma@us.ibm.com>
Return IXGBE_ERR_RAR_INDEX when RAR index is out of range, instead of
returning IXGBE_SUCCESS.

CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

access skb->data safely

we should use skb_header_pointer() and skb_store_bits() to access skb->data to
handle small or non-linear skbs.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
----
 net/sched/act_pedit.c |   24 ++++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This exposes the port number to userland through sysfs.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Probably no one has used this driver on big-endian systems, since it was
setting up descriptor swapping if CONFIG_BIG_ENDIAN is set, which it
never is, since that symbol is not mentioned anywhere else in the kernel
source.  Switch this test to a check for __BIG_ENDIAN so it has a chance
at working.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

copy_to_user() returns the number of bytes remaining but we want to
return a negative error code here.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

copy_from_user() returns the number of bytes remaining but we should
return -EFAULT here.  The error code gets returned to the user.  Both
old_capi_manufacturer() and capi20_manufacturer() had other places
that already returned -EFAULT so this won't break anything.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bitwise negate is intended here.  With the logical negate the
condition is always false.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021.  Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region.  Currently we use the PCI function number, but the
PCI address may be virtualised.  Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use skb_header_pointer() to dereference data safely

the original skb->data dereference isn't safe, as there isn't any skb->len or
skb_is_nonlinear() check. skb_header_pointer() is used instead in this patch.
And when the skb isn't long enough, we terminate the function u32_classify()
immediately with -1.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For large values of rtt, 2^rho operation may overflow u32. Clamp down the increment to 2^16.
Signed-off-by: NDaniele Lacamera <root@danielinux.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix the wrong checksum when addr isn't in old_addr/mask

For TCP and UDP packets, when addr isn't in old_addr/mask we don't do SNAT or
DNAT, and we should not update layer 4 checksum.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
----
 net/sched/act_nat.c |    4 ++++
 1 file changed, 4 insertions(+)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This way, RX DMA overruns (actually being caused by overrun of the
512byte input FIFO) show up in ifconfig output. The rx_fifo_errors
counter is unused otherwise.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch completes commit 89d71a66
which missed this spot, as it seems.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By calling korina_restart(), the IRQ handler tries to disable the
interrupt it's currently serving. This leads to a deadlock since
disable_irq() waits for any running IRQ handlers to finish before
returning. This patch addresses the issue by turning korina_restart()
into a workqueue task, which is then scheduled when needed.

Reproducing the deadlock is easily done using e.g. GNU netcat to send
large amounts of UDP data to the host running this driver.

Note that the same problem (and fix) applies to TX FIFO underruns, but
apparently these are less easy to trigger.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a skb is received on an inactive bond that does not meet
the special cases checked for by skb_bond_should_drop it should
only be delivered to exact matches as the comment in
netif_receive_skb() says.

However because null_or_bond could also be null this is not
always true.  This patch renames null_or_bond to orig_or_bond
and initializes it to orig_dev.  This keeps the intent of
null_or_bond to pass frames received on VLAN interfaces stacked
on bonding interfaces without invalidating the statement for
null_or_orig.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan device should not copy the slave or master flags from
the real device. It is not in the bond until added nor is it
a master.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make get/set netlink VF_PORT truly symmetrical, we need to keep track
of what items are set and only return those items on get.  Previously, the
driver wasn't differentiating between a set of attr with a NULL string,
for example, and not setting the attr at all.  We only want to return
the NULL string if the attr was actually set with a NULL string.  Otherwise,
don't return the attr.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The regression is caused by:

commit 4327ba43
    bnx2: Fix netpoll crash.

If ->open() and ->close() are called multiple times, the same napi structs
will be added to dev->napi_list multiple times, corrupting the dev->napi_list.
This causes free_netdev() to hang during rmmod.

We fix this by calling netif_napi_del() during ->close().

Also, bnx2_init_napi() must not be in the __devinit section since it is
called by ->open().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets going through __xfrm_route_forward() have a not refcounted dst
entry, since we enabled a noref forwarding path.

xfrm_lookup() might incorrectly release this dst entry.

It's a bit late to make invasive changes in xfrm_lookup(), so lets force
a refcount in this path.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function inittiger is only called from nj_init_card, where a lock is held.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@gfp exists@
identifier fn;
position p;
@@

fn(...) {
 ... when != spin_unlock_irqrestore
     when any
 GFP_KERNEL@p
 ... when any
}

@locked@
identifier gfp.fn;
@@

spin_lock_irqsave(...)
...  when != spin_unlock_irqrestore
fn(...)

@depends on locked@
position gfp.p;
@@

- GFP_KERNEL@p
+ GFP_ATOMIC
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing validate_addr hook
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert TX hook to netdev_tx_t type
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

virtio-net bounces buffer allocations off to
a thread if it can't allocate buffers from the atomic
pool. However, if posting buffers still requires atomic
buffers, this is unlikely to succeed.
Fix by passing in the proper gfp_t parameter.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code fails on ppc as hdr.timeout is not being converted
to le32.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes build error caused by the OF device_node pointer
being moved into struct device.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit: c720c7e8 missed these.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct sk_forward_alloc handling for error_queue would need to use a
backlog of frames that softirq handler could not deliver because socket
is owned by user thread. Or extend backlog processing to be able to
process normal and error packets.

Another possibility is to not use mem charge for error queue, this is
what I implemented in this patch.

Note: this reverts commit 29030374
(net: fix sk_forward_alloc corruptions), since we dont need to lock
socket anymore.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit f3c5c1bf (netfilter: xtables: make ip_tables reentrant)
introduced a performance regression, because stackptr array is shared by
all cpus, adding cache line ping pongs. (16 cpus share a 64 bytes cache
line)

Fix this using alloc_percpu()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-By: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

In xt_register_table, xt_jumpstack_alloc is called first, later
xt_replace_table is used. But in xt_replace_table, xt_jumpstack_alloc
will be used again. Then the memory allocated by previous xt_jumpstack_alloc
will be leaked. We can simply remove the previous xt_jumpstack_alloc because
there aren't any users of newinfo between xt_jumpstack_alloc and
xt_replace_table.
Signed-off-by: NXiaotian Feng <dfeng@redhat.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jan Engelhardt <jengelh@medozas.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Acked-By: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

.. and thus endeth the merge window.

* 'slub/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  SLUB: Allow full duplication of kmalloc array for 390
  slub: move kmem_cache_node into it's own cacheline

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  mutex: Fix optimistic spinning vs. BKL

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tui: Fix last use_browser problem related to .perfconfig
  perf symbols: Add the build id cache to the vmlinux path
  perf tui: Reset use_browser if stdout is not a tty
  ring-buffer: Move zeroing out excess in page to ring buffer code
  ring-buffer: Reset "real_end" when page is filled

This partially reverts commit 4ec37de8
("[IA64] Fix build breakage"), since the commit that made it necessary
got reverted earlier (see commit 35926ff5, 'Revert "cpusets:
randomize node rotor used in cpuset_mem_spread_node()"')

Even if we ever re-introduce this, there is no reason to make
__node_random be some architecture-specific function.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  mm: export generic_pipe_buf_*() to modules
  fuse: support splice() reading from fuse device
  fuse: allow splice to move pages
  mm: export remove_from_page_cache() to modules
  mm: export lru_cache_add_*() to modules
  fuse: support splice() writing to fuse device
  fuse: get page reference for readpages
  fuse: use get_user_pages_fast()
  fuse: remove unneeded variable

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-kconfig:
  kconfig: Hide error output in find command in streamline_config.pl
  kconfig: Fix typo in comment in streamline_config.pl
  kconfig: Make a variable local in streamline_config.pl