One of the switch cases has the byte order vs. format bits
reversed to all the other cases. Appease the ocd and reorder
them.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-6-ville.syrjala@linux.intel.com

Docs tell us that on g4x we have to compute the SR watermarks
using 4 bytes per pixel. I'm going to assume that only applies
to 1 and 2 byte per pixel formats, and not 8 byte per pixel
formats. That seems like a recipe for an insufficient watermark
which could lead to underruns. Use the maximum of the two numbers
instead.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-5-ville.syrjala@linux.intel.com

All sprite planes have a progammable gamma ramp. Set it up with
a linear ramp on all platforms. This actually matches the reset
value but soon we'll want to reprogram this ramp on some machines,
so let's just set it up across the board.

Note that on pre-IVB the hardware bypasses the gamma unit
unless a YCbCr pixel format is used.

v2: Add parens around << in ilk_linear_gamma()
    Skip gamma programming for RGB on pre-IVB
    s/DVSGAMC/DVSGAMC_G4X/
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-4-ville.syrjala@linux.intel.com

We don't currently have any use for the sprite gamma on ivb-bdw.
Let's disable it. We already do that on skl+.

On pre-ivb there is no way to disable the sprite gamma, and it
only affects YCbCr pixel formats, whereas on ivb+ it also
affects RGB formats.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-3-ville.syrjala@linux.intel.com

Plane B and C (note that we don't actually expose plane C currently)
on gen2/3 have a window generator, as does the primary plane on CHV
pipe B. So let's allow positioning of these planes freely within the
pipe source area.

Plane A on gen2/3 seems to have some kind of partial window generator
which would allow you to cut the plane off midway through the scanout,
but it would still have to start at the top-left corner of the pipe,
and it would have to be full width. That's doesn't sound all that
useful, so for simplicity let's just keep to the idea that plane A
has to be fullscreen.

Gen4 removed the plane A/B windowing support entirely, and it wasn't
reintroduced until SKL (apart from the CHV pipe B special case).

v2: s/plane/i9xx_plane/ etc. (James)
v3: Make it less confusing
v4: Deal with IS_GEN()
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-2-ville.syrjala@linux.intel.com

PM interrupts belong to the GT so move the variables to be inside
struct intel_gt.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Co-developed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704121756.27824-3-tvrtko.ursulin@linux.intel.com

Mostly in gen11 interrupt handling and a couple neighbouring functions
which were easy since uncore local was already available.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Co-developed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704121756.27824-2-tvrtko.ursulin@linux.intel.com

Some interrupt handling functions already have gt in their names
suggesting them as obvious candidates to make them take struct intel_gt
instead of i915.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Co-developed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704121756.27824-1-tvrtko.ursulin@linux.intel.com

Although polling each engine quickly is preferable as it should give us
a sample of each engine at roughly the same time, keep it simple and
just sample the engine as print out the debug state.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704200455.14870-3-chris@chris-wilson.co.uk

When using MI operations, we do not care which engine we use, so use
them all where possible, and where inconvenient double check we have the
engine we selected at random.

v2: Drop the local copy of engine->sseu to avoid an unchecked deref
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704212343.6820-1-chris@chris-wilson.co.uk

Simplify runtime request creation by storing the context we need to use
during initialisation. This allows us to remove one more hardcoded
engine lookup.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704200455.14870-1-chris@chris-wilson.co.uk

It seems intel_engine_get_instdone is able to get instdone for all engines
but intel_hangcheck.c/subunits_stuck decides to ignore it for non render.

We can just drop the check in subunits_stuck since the checks on
unavailable fields will always return stuck, which when bitwise and with
the potential unstuck instdone is harmless.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703144116.15593-1-tvrtko.ursulin@linux.intel.com

During the context execution tests, we issue a lot of work and discard a
lot of objects without releasing the lock and allowing the background
reaper to free those objects. Insert a small break between each pass to
flush the worker.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704165317.21060-1-chris@chris-wilson.co.uk

On unwinding the allocation error path and having freed the page table
entry, it is imperative that we mark it as scratch.

<4> [416.075569] general protection fault: 0000 [#1] PREEMPT SMP PTI
<4> [416.075801] CPU: 0 PID: 2385 Comm: kworker/u2:11 Tainted: G     U            5.2.0-rc7-CI-Patchwork_13534+ #1
<4> [416.076162] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
<4> [416.076522] Workqueue: i915 __i915_vm_release [i915]
<4> [416.076754] RIP: 0010:gen8_ppgtt_cleanup_3lvl+0x58/0xb0 [i915]
<4> [416.077023] Code: 81 e2 04 fe ff ff 81 c2 ff 01 00 00 4c 8d 74 d6 58 4d 8b 65 00 4d 3b a7 28 02 00 00 74 40 49 8d 5c 24 50 49 81 c4 50 10 00 00 <48> 8b 2b 49 3b af 20 02 00 00 74 13 4c 89 ff 48 89 ee e8 01 fb ff
<4> [416.077445] RSP: 0018:ffffc9000046bd98 EFLAGS: 00010206
<4> [416.077625] RAX: 0001000000000000 RBX: 6b6b6b6b6b6b6bbb RCX: 8b4b56d500000000
<4> [416.077838] RDX: 00000000000001ff RSI: ffff88805a578008 RDI: ffff88805bd0efc8
<4> [416.078167] RBP: ffff88805bd0efc8 R08: 0000000004e42b93 R09: 0000000000000001
<4> [416.078381] R10: 0000000000000000 R11: ffff888077a1b0b8 R12: 6b6b6b6b6b6b7bbb
<4> [416.078594] R13: ffff88805a578058 R14: ffff88805a579058 R15: ffff88805bd0efc8
<4> [416.078815] FS:  0000000000000000(0000) GS:ffff88807da00000(0000) knlGS:0000000000000000
<4> [416.079395] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4> [416.079851] CR2: 000056160fec2b14 CR3: 0000000071bbc003 CR4: 00000000003606f0
<4> [416.080388] Call Trace:
<4> [416.080828]  gen8_ppgtt_cleanup+0x64/0x100 [i915]
<4> [416.081399]  __i915_vm_release+0xfc/0x1d0 [i915]

Fixes: 1d1b5490 ("drm/i915/gtt: Replace struct_mutex serialisation for allocation")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704201656.15775-1-chris@chris-wilson.co.uk

We need to setup the workarounds on all engines, with the knowledge
about which platforms each workaround applies to kept together in the
workaround list. As such, we can pull the w/a initialisation into the
common setup and try to avoid duplicating knowledge about when to setup
the workarounds.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703135805.7310-2-chris@chris-wilson.co.uk

We store separate wa_list on every engine, so be sure to include all
when dumping the current set via debugfs.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703135805.7310-1-chris@chris-wilson.co.uk

New GuC firmware is available. Let's use it.
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703113640.31100-1-michal.wajdeczko@intel.com

Matthew pointed out that we could face a double failure with concurrent
allocations/frees, and so the assumption that the local var alloc was
NULL was fraught with danger. Rather than complicate the error paths too
much to add a second local for a second free, just do the second free
earlier on the unwind path.
Reported-by: NMatthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: NMatthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704104345.6603-1-chris@chris-wilson.co.uk

Expose whether or not we support the PMU software tracking in our
scheduler capabilities, so userspace can query at runtime.

v2: Use I915_SCHEDULER_CAP_ENGINE_BUSY_STATS for a less ambiguous
capability name.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703143702.11339-1-chris@chris-wilson.co.uk

Since reservation_object_fini() does an immediate free, rather than
kfree_rcu as normal, we have to delay the release until after the RCU
grace period has elapsed (i.e. from the rcu cleanup callback) so that we
can rely on the RCU protected access to the fences while the object is a
zombie.

i915_gem_busy_ioctl relies on having an RCU barrier to protect the
reservation in order to avoid having to take a reference and strong
memory barriers.

v2: Order is important; only release after putting the pages!

Fixes: c03467ba ("drm/i915/gem: Free pages before rcu-freeing the object")
Testcase: igt/gem_busy/close-race
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703180601.10950-1-chris@chris-wilson.co.uk

We don't care about the result of the read, so it may be garbage, we
only care that the mmio is flushed. As such, we can forgo using an
individual forcewake and lock around any posting-read for an engine.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703155225.9501-4-chris@chris-wilson.co.uk

We can assume the caller is holding a blanket forcewake for the
register writes during resume, and so we can skip taking individual
locks around each write inside execlists resume.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703155225.9501-3-chris@chris-wilson.co.uk

During post-reset resume, we call intel_mocs_init_engine to reinitialise
the MOCS registers. Suprisingly, especially when enhanced by lockdep,
the acquisition of the forcewake lock around each register write takes a
substantial portion of the reset time. We don't need to use the
individual forcewake here as we can assume that the caller is holding a
blanket forcewake for the reset&resume and the resume is serialised.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703155225.9501-2-chris@chris-wilson.co.uk

The intent of the assert is to document that the caller took the
appropriate wakerefs for the function. However, as Tvrtko pointed out,
we simply check whether the fw_domains are active and may be confused by
the auto wakeref which may be dropped between the check and use. Let's
be more careful in the assert and check that each fw_domain has an
explicit caller wakeref above and beyond the automatic wakeref.

v2: Fix spelling for config DRM_I915_DEBUG_RUNTIME_PM
v3: Timer may still be active after we drop the autowakeref, we need to
check domain->active instead.
v4: The timer checks domain->active, but we still need to check the
timer. (This is starting to look weird...)
Reported-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704102048.6436-1-chris@chris-wilson.co.uk

Trying to drain a workqueue while we may still be adding to it from
background tasks is, according to kernel/workqueue.c, verboten. So, add
a flush_workqueue() at the start of our cleanup procedure.

References: https://bugs.freedesktop.org/show_bug.cgi?id=110550Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703171913.16585-4-chris@chris-wilson.co.uk

The render state is used to initialise the default RCS context, and only
used during early setup from within the gt code. As such, it makes a
good candidate for placing within gt/, even if it is not yet entirely
clean of our GEM heritage.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704091925.7391-1-chris@chris-wilson.co.uk

If we hit an error while allocating the page tables, we have to unwind
the incomplete updates, and wish to free the unused pd. However, we are
not allowed to be hoding the spinlock at that point, and so must use the
later free to defer it until after we drop the lock.

<3> [414.363795] BUG: sleeping function called from invalid context at drivers/gpu/drm/i915/i915_gem_gtt.c:472
<3> [414.364167] in_atomic(): 1, irqs_disabled(): 0, pid: 3905, name: i915_selftest
<4> [414.364406] 3 locks held by i915_selftest/3905:
<4> [414.364408]  #0: 0000000034fe8aa8 (&dev->mutex){....}, at: device_driver_attach+0x18/0x50
<4> [414.364415]  #1: 000000006bd8a560 (&dev->struct_mutex){+.+.}, at: igt_ctx_exec+0xb7/0x410 [i915]
<4> [414.364476]  #2: 000000003dfdc766 (&(&pd->lock)->rlock){+.+.}, at: gen8_ppgtt_alloc_pdp+0x448/0x540 [i915]
<3> [414.364529] Preemption disabled at:
<4> [414.364530] [<0000000000000000>] 0x0
<4> [414.364696] CPU: 0 PID: 3905 Comm: i915_selftest Tainted: G     U            5.2.0-rc7-CI-CI_DRM_6403+ #1
<4> [414.364698] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
<4> [414.364699] Call Trace:
<4> [414.364704]  dump_stack+0x67/0x9b
<4> [414.364708]  ___might_sleep+0x167/0x250
<4> [414.364777]  vm_free_page+0x24/0xc0 [i915]
<4> [414.364852]  free_pd+0xf/0x20 [i915]
<4> [414.364897]  gen8_ppgtt_alloc_pdp+0x489/0x540 [i915]
<4> [414.364946]  gen8_ppgtt_alloc_4lvl+0x8e/0x2e0 [i915]
<4> [414.364992]  ppgtt_bind_vma+0x2e/0x60 [i915]
<4> [414.365039]  i915_vma_bind+0xe8/0x2c0 [i915]
<4> [414.365088]  __i915_vma_do_pin+0xa1/0xd20 [i915]

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111050
Fixes: 1d1b5490 ("drm/i915/gtt: Replace struct_mutex serialisation for allocation")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703171913.16585-3-chris@chris-wilson.co.uk

Adding N & CTS values for 10/12 bit deep color from Appendix C
table in HDMI 2.0 spec. The correct values for N is not chosen
automatically by hardware for deep color modes.

v2: Remove unnecessary initialization of size
Signed-off-by: NAditya Swarup <aditya.swarup@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627220708.31700-2-aditya.swarup@intel.com

Use port_clock to check the clock values in n/cts lookup table instead
of crtc_clock. As port_clock is already adjusted based on color mode set
(8 bit or deep color), this will help in checking clock values for deep
color modes from n/cts lookup table.
Signed-off-by: NAditya Swarup <aditya.swarup@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627220708.31700-1-aditya.swarup@intel.com

When SAGV is forced to disabled/min/med/max in the BIOS pcode will
only hand us a single QGV point instead of the normal three. Fix
the code to deal with that instead declaring the bandwidth limit
to be 0 MB/s (and thus preventing any planes from being enabled).

Also shrink the max_bw sturct a bit while at it, and change the
deratedbw type to unsigned since the code returns the bw as
an unsigned int.

Since we now keep track of how many qgv points we got from pcode
we can drop the earlier check added for the "pcode doesn't
support the memory subsystem query" case.

Cc: felix.j.degrood@intel.com
Cc: Mark Janes <mark.a.janes@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Fixes: c457d9cf ("drm/i915: Make sure we have enough memory bandwidth on ICL")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110838Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606124210.3482-1-ville.syrjala@linux.intel.comReviewed-by: NMatt Roper <matthew.d.roper@intel.com>

Since a shrinker may be forced to wait on GPU activity,
i915_active_wait(&vma->active) must be safe for use inside a shrinker,
and so let's mark up the lock as being acquired by the shrinker to avoid
any nasty surprises creeping in.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703091726.11690-8-chris@chris-wilson.co.uk

Make the lockchains more deterministic via i915_active by flagging the
potential lock.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703091726.11690-7-chris@chris-wilson.co.uk

As we have dropped the final reference to the object, we do not need to
wait until after the rcu grace period to drop its pages. We still require
struct_mutex to completely unbind the object to release the pages, so we
still need a free-worker to manage that from process context. By
scheduling the release of pages before waiting for the rcu should mean
that we are not trapping those pages from beyond the reach of the
shrinker.

v2: Pass along the request to skip if the vma is busy to the underlying
unbind routine, to avoid checking the reservation underneath the
i915->mm.obj_lock which may be used from inside irq context.

v3: Flip the bit for unbinding while active, for later convenience.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111035
Fixes: a93615f9 ("drm/i915: Throw away the active object retirement complexity")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703091726.11690-6-chris@chris-wilson.co.uk

Be a little more hesitant before injecting a timeslice, and try to take
into account any change in priority that is due for the running task
before switching to another task. This will allow us to arbitrarily
prevent switching away from a request if we deem it necessarily to
disable preemption, for instance.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Acked-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703091726.11690-9-chris@chris-wilson.co.uk

Remember to lock the drm_mm as we modify it, lest it be modified in the
background by retire/free workers!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703091726.11690-2-chris@chris-wilson.co.uk

We frequently, but not frequently enough!, remember to flush residual
operations and objects at the end of a live subtest. The purpose is to
cleanup after every subtest, leaving a clean slate for the next subtest,
and perform early detection of leaky state. As this should ideally be
common for all live subtests, pull the task into a common teardown
routine.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703091726.11690-1-chris@chris-wilson.co.uk

icl-dsi is dying on suspend/resume at

	RIP: 0010:icl_update_active_dpll+0x2c/0xa0 [i915]

which appears due to the loss of the time primary_port across suspend.
Protect against the potential NULL dereference by assuming
ICL_PORT_DPLL_DEFAULT unless the port is actively specified otherwise.

Fixes: 24a7bfe0 ("drm/i915: Keep the TypeC port mode fixed when the port is active")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702140950.7069-1-chris@chris-wilson.co.uk

When eliminating our use of drm_irq_install() I failed to convert
all our synchronize_irq() calls to consult pdev->irq instead of
dev_priv->drm.irq. As we no longer populate dev_priv->drm.irq
we're no longer synchronizing against anything.

v2: Add intel_syncrhonize_irq() (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: NImre Deak <imre.deak@intel.com>
Fixes: b318b824 ("drm/i915: Nuke drm_driver irq vfuncs")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111012Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702151723.29739-1-ville.syrjala@linux.intel.com

We missed one place where we check PPGTT-only platform for PPGTT
presence. Let's remove it.
While I'm here let's assert that this particular code is never called on
pre-gen8 platforms.

References: 4bdafb9d ("drm/i915: Remove i915.enable_ppgtt override")
Signed-off-by: NMichał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702113149.21200-2-michal.winiarski@intel.com

This reverts commit 4395890a.

It's been over a year since this was merged, and the actual users of
intel_ppat_get / intel_ppat_put never materialized.

Time to remove it!

v2: Unbreak suspend (Chris)
v3: Rebase, drop fixes tag to avoid confusion
Signed-off-by: NMichał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702113149.21200-1-michal.winiarski@intel.com