Fix the pointer rtl_fw->fw would be used before checking in
rtl8152_apply_firmware() that causes the following kernel oops.

Unable to handle kernel NULL pointer dereference at virtual address 00000002
pgd = (ptrval)
[00000002] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 131 Comm: kworker/0:2 Not tainted
5.4.0-rc1-00539-g9370f2d0 #6788
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events_long rtl_hw_phy_work_func_t
PC is at rtl8152_apply_firmware+0x14/0x464
LR is at r8153_hw_phy_cfg+0x24/0x17c
pc : [<c064f4e4>]    lr : [<c064fa18>]    psr: a0000013
sp : e75c9e60  ip : 60000013  fp : c11b7614
r10: e883b91c  r9 : 00000000  r8 : fffffffe
r7 : e883b640  r6 : fffffffe  r5 : fffffffe  r4 : e883b640
r3 : 736cfe7c  r2 : 736cfe7c  r1 : 000052f8  r0 : e883b640
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: 6640006a  DAC: 00000051
Process kworker/0:2 (pid: 131, stack limit = 0x(ptrval))
Stack: (0xe75c9e60 to 0xe75ca000)
...
[<c064f4e4>] (rtl8152_apply_firmware) from [<c064fa18>]
(r8153_hw_phy_cfg+0x24/0x17c)
[<c064fa18>] (r8153_hw_phy_cfg) from [<c064e784>]
(rtl_hw_phy_work_func_t+0x220/0x3e4)
[<c064e784>] (rtl_hw_phy_work_func_t) from [<c0148a74>]
(process_one_work+0x22c/0x7c8)
[<c0148a74>] (process_one_work) from [<c0149054>] (worker_thread+0x44/0x520)
[<c0149054>] (worker_thread) from [<c0150548>] (kthread+0x130/0x164)
[<c0150548>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xe75c9fb0 to 0xe75c9ff8)
...

Fixes: 9370f2d0 ("r8152: support request_firmware for RTL8153")
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Madalin Bucur says:

====================
DPAA Ethernet changes

v3: add newline at the end of error messages
v2: resending with From: field matching signed-off-by

Here's a series of changes for the DPAA Ethernet, addressing minor
or unapparent issues in the codebase, adding probe ordering based on
a recently added DPAA QMan API, removing some redundant code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newline was missing at the end of the error message.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DPAA Ethernet driver is using the FMan MAC as the device for DMA
mapping. This is not actually correct, as the real DMA device is the
FMan port (the FMan Rx port for reception and the FMan Tx port for
transmission). Changing the device used for DMA mapping to the Fman
Rx and Tx port devices.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NLaurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an API that retrieves the 'struct device' that the specified FMan
port probed against. The new API will be used in a subsequent patch
that corrects the DMA devices used by the dpaa_eth driver.
Signed-off-by: NLaurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Condition was previously checked, removing duplicate code.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will
cause a boot crash. Add predictability in the probing order by deferring
the Ethernet driver probe after QBMan and portals by using the recently
introduced QBMan APIs.
Signed-off-by: NLaurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The liodn base registers are specific to PAMU based NXP systems and are
reserved on SMMU based ones. Don't access them unless PAMU is compiled in.
Signed-off-by: NLaurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: PTP support for AQC devices

This patchset introduces PTP feature support in Aquantia AQC atlantic driver.

This implementation is a joined effort of aquantia developers:
Egor is the main designer and driver/firmware architect on PTP,
Sergey and Dmitry are included as co-developers.
Dmitry also helped me in the overall patchset preparations.

Feature was verified on AQC hardware with testptp tool, linuxptp,
gptp and with Motu hardware unit.

version3 updates:
- Review comments applied: error handling, various fixes

version2 updates:
- Fixing issues from Andrew's review: replacing self with
  ptp var name, making ptp_clk_offset a field in the ptp instance.
  devm_kzalloc advice is actually non applicable, because ptp object gets
  created/destroyed on each network device close/open and it should not be
  linked with dev lifecycle.
- Rearranging commit authorship, adding Egor as a ptp module main maintainer
- Fixing kbuild 32bit division issues
====================
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTP implementation is designed and maintained by Egor Pomozov, adding
him as this module maintainer. Egor is the author of the core
functionality and the architect, and is to be contacted for
all Aquantia PTP/AVB functionality.
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on FW configuration we can manage from 0 to 3 PINs for periodic output
and from 0 to 1 ext ts PIN for getting TS for external event.

Ext TS PIN functionality is implemented via periodic timestamps polling
directly from PHY, because right now there is now way to receive the
PIN trigger interrupt from phy.

The polling interval is 15 milliseconds.
Co-developed-by: NEgor Pomozov <epomozov@marvell.com>
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Co-developed-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GPIO PIN control and access is done by direct phy manipulation.
Here we add an aq_phy module which is able to access phy registers
via MDIO access mailbox.

Access is controlled via HW semaphore.
Co-developed-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool callback with basic information on what PTP features are supported
by the device.
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Co-developed-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here we add support for PTP specific IOCTLs of HW timestamp get/set.

These will use filters to configure flows onto the required queue ids.
Co-developed-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We implement HW filter reservation for PTP traffic. Special location
in filters table is marked as reserved, because incoming ptp traffic
should be directed only to PTP designated queue. This way HW will do PTP
timestamping and proper processing.
Co-developed-by: NEgor Pomozov <epomozov@marvell.com>
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Co-developed-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here we do alloc/free IRQs for PTP rings.
We also implement processing of PTP packets on TX and RX sides.
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Co-developed-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checkpatch and styling fixes on parts of code touched by ptp
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add implementations of PTP rings alloc/free.

PTP desing on this device uses two separate rings on a separate traffic
class for traffic rx/tx.

Third ring (hwts) is not a traffic ring, but is used only to receive timestamps
of the transmitted packets.
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Co-developed-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Basic HW functions implemented for adjusting frequency,
adjusting time, getting and setting time.
With these callbacks we now do register ptp clock in the system.

Firmware interface parts are defined for PTP requests and interactions.
Enable/disable PTP counters in HW on clock register/unregister.
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Co-developed-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make some other bit-enums more clear about positioning,
this helps on debugging and development
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here we add basic function for PTP clock register/unregister.
We also declare FW/HW capability bits used to control PTP feature on device.

PTP device is created if network card has appropriate FW that has PTP
enabled in config. HW supports timestamping for PTPv2 802.AS1 and
PTPv2 IPv4 UDP packets.

It also supports basic PTP callbacks for getting/setting time, adjusting
frequency and time as well.
Signed-off-by: NEgor Pomozov <epomozov@marvell.com>
Co-developed-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: NSergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NDmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/usb/lan78xx.c:3995:6: warning:
 variable event set but not used [-Wunused-but-set-variable]

It is never used, so can be removed.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Update main pool computation and pool size limits

Petr says:

In Spectrum ASICs, the shared buffer is an area of memory where packets are
kept until they can be transmitted. There are two resources associated with
shared buffer size: cap_total_buffer_size and cap_guaranteed_shared_buffer.
So far, mlxsw has been using the former as a limit when validating shared
buffer pool size configuration. However, the total size also includes
headrooms and reserved space, which really cannot be used for shared buffer
pools. Patch #1 mends this and has mlxsw use the guaranteed size.

To configure default pool sizes, mlxsw has historically hard-coded one or
two smallish pools, and one "main" pool that took most of the shared buffer
(that would be pool 0 on ingress and pool 4 on egress). During the
development of Spectrum-2, it became clear that the shared buffer size
keeps shrinking as bugs are identified and worked around. In order to
prevent having to tweak the size of pools 0 and 4 to catch up with updates
to values reported by the FW, patch #2 changes the way these pools are set.
Instead of hard-coding a fixed value, the main pool now takes whatever is
left from the guaranteed size after the smaller pool(s) are taken into
account.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of hard-coding the size of the largest pool, calculate it from the
reported guaranteed shared buffer size and sizes of other pools (currently
only the CPU port pool).
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two resources associated with shared buffer size:
cap_total_buffer_size, and cap_guaranteed_shared_buffer. So far, mlxsw has
been using the former as a limit to determine how large a pool size is
allowed to be. However, the total size also includes headrooms and reserved
space, which really cannot be used for shared buffer pools.

Therefore convert mlxsw to use the latter resource as a limit. Adjust
hard-coded pool sizes to be the guaranteed size minus 256000 bytes for CPU
port pool. On Spectrum-1 that actually leads to an increase. A follow-up
patch will have this size calculated automatically.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting PCI_EXP_DEVCTL_NOSNOOP_EN for certain chip versions had been
added to the vendor driver more than 10 years ago, and copied from
there to r8169. It has been removed from the vendor driver meanwhile
and I think we can safely remove this too.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tao Ren says:

====================
net: phy: support 1000Base-X auto-negotiation for BCM54616S

This patch series aims at supporting auto negotiation when BCM54616S is
running in 1000Base-X mode: without the patch series, BCM54616S PHY driver
would report incorrect link speed in 1000Base-X mode.

Patch #1 (of 3) modifies assignment to OR when dealing with dev_flags in
phy_attach_direct function, so that dev_flags updated in BCM54616S PHY's
probe callback won't be lost.

Patch #2 (of 3) adds several genphy_c37_* functions to support clause 37
1000Base-X auto-negotiation, and these functions are called in BCM54616S
PHY driver.

Patch #3 (of 3) detects BCM54616S PHY's operation mode and calls according
genphy_c37_* functions to configure auto-negotiation and parse link
attributes (speed, duplex, and etc.) in 1000Base-X mode.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BCM54616S PHY cannot work properly in RGMII->1000Base-X mode, mainly
because genphy functions are designed for copper links, and 1000Base-X
(clause 37) auto negotiation needs to be handled differently.

This patch enables 1000Base-X support for BCM54616S by customizing 3
driver callbacks, and it's verified to be working on Facebook CMM BMC
platform (RGMII->1000Base-KX):

  - probe: probe callback detects PHY's operation mode based on
    INTERF_SEL[1:0] pins and 1000X/100FX selection bit in SerDES 100-FX
    Control register.

  - config_aneg: calls genphy_c37_config_aneg when the PHY is running in
    1000Base-X mode; otherwise, genphy_config_aneg will be called.

  - read_status: calls genphy_c37_read_status when the PHY is running in
    1000Base-X mode; otherwise, genphy_read_status will be called.

Note: BCM54616S PHY can also be configured in RGMII->100Base-FX mode, and
100Base-FX support is not available as of now.
Signed-off-by: NTao Ren <taoren@fb.com>
Acked-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for clause 37 1000Base-X auto-negotiation.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NTao Ren <taoren@fb.com>
Tested-by: NRené van Dorst <opensource@vdorst.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify the assignment to OR when dealing with phydev->dev_flags in
phy_attach_direct function, and this is to make sure dev_flags set in
driver's probe callback won't be lost.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: NTao Ren <taoren@fb.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 342db221 ("sched: Call skb_get_hash_perturb
in sch_fq_codel") we no longer need anything from this file.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Vivien Didelot says:

====================
The dsa_switch structure represents the physical switch device itself,
and is allocated by the driver. The dsa_switch_tree and dsa_port structures
represent the logical switch fabric (eventually composed of multiple switch
devices) and its ports, and are allocated by the DSA core.

This branch lists the logical ports directly in the fabric which simplifies
the iteration over all ports when assigning the default CPU port or configuring
the D in DSA in drivers like mv88e6xxx.

This also removes the unique dst->cpu_dp pointer and is a first step towards
supporting multiple CPU ports and dropping the DSA_MAX_PORTS limitation.

Because the dsa_port structures are not tied to the dsa_switch structure
anymore, we do not need to provide an helper for the drivers to allocate a
switch structure. Like in many other subsystems, drivers can now embed their
dsa_switch structure as they wish into their private structure. This will
be particularly interesting for the Broadcom drivers which were currently
limited by the dynamically allocated array of DSA ports.

The series implements the list of dsa_port structures, makes use of it,
then drops dst->cpu_dp and the dsa_switch_alloc helper.
====================
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Allocate the struct dsa_port the first time it is accessed with
dsa_port_touch, and remove the static dsa_port array from the
dsa_switch structure.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Like the dsa_switch_tree structures, the dsa_port structures will be
allocated on switch registration.

The SJA1105 driver is the only one accessing the dsa_port structure
after the switch allocation and before the switch registration.
For that reason, move switch registration prior to assigning the priv
member of the dsa_port structures.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list
of switch fabric ports to remap the Port VLAN Map of local bridge
group members or remap the Port VLAN Table entry of external bridge
group members.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Instead of digging into the other dsa_switch structures of the fabric
and relying too much on the dsa_to_port helper, use the new list of
switch fabric ports to define the mask of the local ports allowed to
receive frames from another port of the fabric.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Since mv88e6xxx_pvt_map is a static helper, no need to return
-EOPNOTSUPP if the chip has no PVT, simply silently skip the operation.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Use the new ports list instead of iterating over switches and their
ports when setting up the default CPU port. Unassign it on teardown.

Now that we can iterate over multiple CPU ports, remove dst->cpu_dp.

At the same time, provide a better error message for CPU-less tree.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>