Add a new function regmap_get_device to obtain the underlying struct
device from a regmap.
Signed-off-by: NTuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers

Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains several fixes for Scsi START_STOP_UNIT. The previous
code did not account for signed vs. unsigned arithmetic which resulted
in an invalid lowest power state caculation when the device only supports
1 power state.

The code for Power Condition == 2 (Idle) was not following the spec. The
spec calls for setting the device to specific power states, depending
upon Power Condition Modifier, without accounting for the number of
power states supported by the device.

The code for Power Condition == 3 (Standby) was using a hard-coded '0'
which is replaced with the macro POWER_STATE_0.
Signed-off-by: NDan McLeran <daniel.mcleran@intel.com>
Reviewed-by: NVishal Verma <vishal.l.verma@linux.intel.com>
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>

The nvme-scsi file defined its own Log Page constant.  Use the
newly-defined one from the header file instead.
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>

There is a potential dead lock if a cpu event occurs during nvme probe
since it registered with hot cpu notification. This fixes the race by
having the module register with notification outside of probe rather
than have each device register.

The actual work is done in a scheduled work queue instead of in the
notifier since assigning IO queues has the potential to block if the
driver creates additional queues.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>

This patch fixes a NULL pointer dereference regression bug that was
introduced with:

commit 1e1110c4
Author: Mikulas Patocka <mpatocka@redhat.com>
Date:   Sat May 17 06:49:22 2014 -0400

    target: fix memory leak on XCOPY

Now that target_put_sess_cmd() -> kref_put_spinlock_irqsave() is
called with a valid se_cmd->cmd_kref, a NULL pointer dereference
is triggered because the XCOPY passthrough commands don't have
an associated se_session pointer.

To address this bug, go ahead and checking for a NULL se_sess pointer
within target_put_sess_cmd(), and call se_cmd->se_tfo->release_cmd()
to release the XCOPY's xcopy_pt_cmd memory.
Reported-by: NThomas Glanzmann <thomas@glanzmann.de>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.

Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch

$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[  3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0- 3.0 sec   181 MBytes   506 Mbits/sec

During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.

CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.

Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.

$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[  3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0- 3.0 sec  99.5 MBytes   278 Mbits/sec

$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[  3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0- 3.0 sec   154 MBytes   432 Mbits/sec

CC: Li Frank <B20596@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support SG, software TSO, let's increase BD entry number.

CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to enhance the code readable, let's factorize the
feature list.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IP header checksum is calcalated by network layer in default.
To support software TSO, it is better to use HW calculate the
IP header checksum.

FEC hw checksum feature request the checksum field in frame
is zero, otherwise the calculative CRC is not correct.

For segmentated TCP packet, HW calculate the IP header checksum again,
it doesn't bring any impact. For SW TSO, HW calculated checksum bring
better performance.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.

And the patch also factorize the getting BD index to it own function.

CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With some specific configuration (VT6105M on Soekris 5510 and depending
on the device at the other end), fragmented packets were not transmitted
when forcing 100 full-duplex with autoneg disable.

This fix now write full-duplex chips register when forcing full or
half-duplex not only when autoneg is enable.
Signed-off-by: NFrançois Cachereul <f.cachereul@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A malicious VF might try to starve the other VFs & PF by creating
contineous doorbell floods. In order to negate this, HW has a threshold of
doorbells per client, which will stop the client doorbells from arriving
if crossed.

The threshold currently configured for VFs is too low - under extreme traffic
scenarios, it's possible for a VF to reach the threshold and thus for its
fastpath to stop working.
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If L2FW utilized by the UNDI driver has the same version number as that
of the regular FW, a driver loading after UNDI and receiving an uncommon
answer from management will mistakenly assume the loaded FW matches its
own requirement and try to exist the flow via FLR.
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the phy access mode even in case of link-flap avoidance.
Signed-off-by: NYaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids clearing the RX polarity setting in KR mode when polarity lane
is swapped, as otherwise this will result in failed link.
Signed-off-by: NYaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: NYuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: NAriel Elior <ariel.elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_hwmon_device_register_with_groups instead of
the old-style manual attributes and hwmon device registration.

Also, unroll the attribute group macros for better code
readability.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Move atxp1_id and atxp1_driver to proper place to avoid forward declaration.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add support for Sensirion SHTC1 and compatible temperature and humidity
sensors.
Signed-off-by: NTomas Pop <tomas.pop@sensirion.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups to
simplify the code a bit.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Tested-by: NPer Dalén <per.dalen@appeartv.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Generic detection leads to too many false positives, so drop it. FWIW
sensors-detect does not have such generic detection. If the user wants
to force the driver to bind to a not yet supported chip, he/she can
still do so using sysfs attribute new_device.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

All devices supported by ina2xx are bidirectional and report the
measured shunt voltage and power values as a signed 16 bit, but the
current driver implementation caches all registers as u16, leading
to an incorrect sign extension when reporting to userspace in
ina2xx_get_value().

This patch fixes the problem by casting the signed registers to s16.
Tested on an INA219.
Signed-off-by: NFabio Baltieri <fabio.baltieri@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

We have a number of front-end drivers for SDHCI_PLTFM, some of them
use 'select MMC_SDHCI_PLTFM', others use 'depends on'. This is
inconsistent and confusing, and in one case has also led to a
build error because of incomplete dependencies:

warning: (MMC_SDHCI_PXAV3 && MMC_SDHCI_PXAV2 && MMC_SDHCI_BCM_KONA) selects MMC_SDHCI_PLTFM which has unmet direct dependencies (MMC && MMC_SDHCI)
drivers/built-in.o: In function `sdhci_sirf_resume':
:(.text+0xaaacb4): undefined reference to `sdhci_resume_host'
drivers/built-in.o: In function `sdhci_sirf_suspend':
:(.text+0xaaacf8): undefined reference to `sdhci_suspend_host'
drivers/built-in.o: In function `sdhci_sirf_probe':
:(.text+0xaaaf44): undefined reference to `sdhci_add_host'
:(.text+0xaaaf50): undefined reference to `sdhci_remove_host'

This changes Kconfig to use 'depends on MMC_SDHCI_PLTFM' for all these
cases, to fix the build error and make the logic more logical.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC host driver should not select the pmic driver, since that
may have other dependencies, notably i2c in this case. It's not
clear what the exact requirement of the driver is, but to preserve
the behavior, this patch changes the 'select' into 'depends on',
meaning you now have to turn on TPS65010 explicitly and then
MMC_OMAP.

Found during randconfig build testing.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

gcc correctly points out that hw_state can be used uninitially
in the mvsd_setup_data() function. This rearranges the function
to ensure it always contains a proper value.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Chris Ball <chris@printf.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linux-mmc@vger.kernel.org
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This avoids a build error due to the use of flush_dcache_page.

drivers/mmc/host/atmel-mci.c: In function 'atmci_read_data_pio':
drivers/mmc/host/atmel-mci.c:1870:5: error: implicit declaration of function 'flush_dcache_page' [-Werror=implicit-function-declaration]
     flush_dcache_page(sg_page(sg));
     ^
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sdhci core was refactored recently and some of those
refactorings required changes in every sdhci platform driver.
Those updates happened around the same time as when the msm
driver was merged so the refactorings missed the msm driver.
Hook in the basic library functions so that we can boot apq8074
dragonboards again instead of crashing when we try to jump to
NULL function pointers.
Reported-by: NKevin Hilman <khilman@linaro.org>
Cc: Georgi Djakov <gdjakov@mm-sol.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NKumar Gala <galak@codeaurora.org>
Reviewed-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix a number of wrong print formats.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit dd34c37a (gpio: of: Allow -gpio suffix for property names)
added parsing for both -gpio and -gpios suffix but also changed
the handling for deferred probe unintentionally. Because of the
looping the second name will now return -ENOENT instead of
-EPROBE_DEFER. Fix the issue by breaking out of the loop if
-EPROBE_DEFER is encountered.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NShruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print the device address, the register number and the PHY ID for
which the MDIO read operation failed
Signed-off-by: NShruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to gro_postpull_rcsum for GRO to work with checksum complete.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Check interrupt mode at the start of qlcnic_set_channels().
- Do not validate ring count if they are not going to change.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pre-allocate the physically contiguous DMA buffer used for
minidump collection at driver load time, rather than at
run time, to minimize allocation failures. Driver will allocate
the buffer at load time if PEX DMA support capability is indicated
by the adapter.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We recently change the kzalloc() to devm_kzalloc() so freeing "ctlr"
here could lead to a double free.

Fixes: e1943128 ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a typo here so we return directly instead of unwinding.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adds the device managed APIs so that no need worry about
freeing the resources.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>