Upon detection of an unarmed dimm in a region, arrange for descendant
BTT, PMEM, or BLK instances to be read-only.  A dimm is primarily marked
"unarmed" via flags passed by platform firmware (NFIT).

The flags in the NFIT memory device sub-structure indicate the state of
the data on the nvdimm relative to its energy source or last "flush to
persistence".  For the most part there is nothing the driver can do but
advertise the state of these flags in sysfs and emit a message if
firmware indicates that the contents of the device may be corrupted.
However, for the case of ACPI_NFIT_MEM_ARMED, the driver can arrange for
the block devices incorporating that nvdimm to be marked read-only.
This is a safe default as the data is still available and new writes are
held off until the administrator either forces read-write mode, or the
energy source becomes armed.

A 'read_only' attribute is added to REGION devices to allow for
overriding the default read-only policy of all descendant block devices.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

'libnvdimm' is the first driver sub-system in the kernel to implement
mocking for unit test coverage.  The nfit_test module gets built as an
external module and arranges for external module replacements of nfit,
libnvdimm, nd_pmem, and nd_blk.  These replacements use the linker
--wrap option to redirect calls to ioremap() + request_mem_region() to
custom defined unit test resources.  The end result is a fully
functional nvdimm_bus, as far as userspace is concerned, but with the
capability to perform otherwise destructive tests on emulated resources.

Q: Why not use QEMU for this emulation?
QEMU is not suitable for unit testing.  QEMU's role is to faithfully
emulate the platform.  A unit test's role is to unfaithfully implement
the platform with the goal of triggering bugs in the corners of the
sub-system implementation.  As bugs are discovered in platforms, or the
sub-system itself, the unit tests are extended to backstop a fix with a
reproducer unit test.

Another problem with QEMU is that it would require coordination of 3
software projects instead of 2 (kernel + libndctl [1]) to maintain and
execute the tests.  The chances for bit rot and the difficulty of
getting the tests running goes up non-linearly the more components
involved.


Q: Why submit this to the kernel tree instead of external modules in
   libndctl?
Simple, to alleviate the same risk that out-of-tree external modules
face.  Updates to drivers/nvdimm/ can be immediately evaluated to see if
they have any impact on tools/testing/nvdimm/.


Q: What are the negative implications of merging this?
It is a unique maintenance burden because the purpose of mocking an
interface to enable a unit test is to purposefully short circuit the
semantics of a routine to enable testing.  For example
__wrap_ioremap_cache() fakes the pmem driver into "ioremap()'ing" a test
resource buffer allocated by dma_alloc_coherent().  The future
maintenance burden hits when someone changes the semantics of
ioremap_cache() and wonders what the implications are for the unit test.

[1]: https://github.com/pmem/ndctl

Cc: <linux-acpi@vger.kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The libnvdimm implementation handles allocating dimm address space (DPA)
between PMEM and BLK mode interfaces.  After DPA has been allocated from
a BLK-region to a BLK-namespace the nd_blk driver attaches to handle I/O
as a struct bio based block device. Unlike PMEM, BLK is required to
handle platform specific details like mmio register formats and memory
controller interleave.  For this reason the libnvdimm generic nd_blk
driver calls back into the bus provider to carry out the I/O.

This initial implementation handles the BLK interface defined by the
ACPI 6 NFIT [1] and the NVDIMM DSM Interface Example [2] composed from
DCR (dimm control region), BDW (block data window), IDT (interleave
descriptor) NFIT structures and the hardware register format.
[1]: http://www.uefi.org/sites/default/files/resources/ACPI_6.0.pdf
[2]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf

Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boaz Harrosh <boaz@plexistor.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Most discovery/configuration of the nvdimm-subsystem is done via sysfs
attributes.  However, some nvdimm_bus instances, particularly the
ACPI.NFIT bus, define a small set of messages that can be passed to the
platform.  For convenience we derive the initial libnvdimm-ioctl command
formats directly from the NFIT DSM Interface Example formats.

    ND_CMD_SMART: media health and diagnostics
    ND_CMD_GET_CONFIG_SIZE: size of the label space
    ND_CMD_GET_CONFIG_DATA: read label space
    ND_CMD_SET_CONFIG_DATA: write label space
    ND_CMD_VENDOR: vendor-specific command passthrough
    ND_CMD_ARS_CAP: report address-range-scrubbing capabilities
    ND_CMD_ARS_START: initiate scrubbing
    ND_CMD_ARS_STATUS: report on scrubbing state
    ND_CMD_SMART_THRESHOLD: configure alarm thresholds for smart events

If a platform later defines different commands than this set it is
straightforward to extend support to those formats.

Most of the commands target a specific dimm.  However, the
address-range-scrubbing commands target the bus.  The 'commands'
attribute in sysfs of an nvdimm_bus, or nvdimm, enumerate the supported
commands for that object.

Cc: <linux-acpi@vger.kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: NNicholas Moulin <nicholas.w.moulin@linux.intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Enable nvdimm devices to be registered on a nvdimm_bus.  The kernel
assigned device id for nvdimm devicesis dynamic.  If userspace needs a
more static identifier it should consult a provider-specific attribute.
In the case where NFIT is the provider, the 'nmemX/nfit/handle' or
'nmemX/nfit/serial' attributes may be used for this purpose.

Cc: Neil Brown <neilb@suse.de>
Cc: <linux-acpi@vger.kernel.org>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The control device for a nvdimm_bus is registered as an "nd" class
device.  The expectation is that there will usually only be one "nd" bus
registered under /sys/class/nd.  However, we allow for the possibility
of multiple buses and they will listed in discovery order as
ndctl0...ndctlN.  This character device hosts the ioctl for passing
control messages.  The initial command set has a 1:1 correlation with
the commands listed in the by the "NFIT DSM Example" document [1], but
this scheme is extensible to future command sets.

Note, nd_ioctl() and the backing ->ndctl() implementation are defined in
a subsequent patch.  This is simply the initial registrations and sysfs
attributes.

[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf

Cc: Neil Brown <neilb@suse.de>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: <linux-acpi@vger.kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

A struct nvdimm_bus is the anchor device for registering nvdimm
resources and interfaces, for example, a character control device,
nvdimm devices, and I/O region devices.  The ACPI NFIT (NVDIMM Firmware
Interface Table) is one possible platform description for such
non-volatile memory resources in a system.  The nfit.ko driver attaches
to the "ACPI0012" device that indicates the presence of the NFIT and
parses the table to register a struct nvdimm_bus instance.

Cc: <linux-acpi@vger.kernel.org>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NJeff Moyer <jmoyer@redhat.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NToshi Kani <toshi.kani@hp.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>