Skip to content

C
clone-Linux

gsplhtlxg / clone-Linux

通知 2
Star 0
Fork 1
C
clone-Linux

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 09 7月, 2015 1 次提交
  3. 22 6月, 2015 2 次提交
  5. 13 5月, 2015 1 次提交
  7. 08 4月, 2015 10 次提交
  9. 31 3月, 2015 2 次提交
    • J
      MIPS: Read CPU IRQ line that FDC to routed to · 8f7ff027
      由 James Hogan 提交于 
      Read the CPU IRQ line reportedly used for the Fast Debug Channel (FDC)
interrupt from the IntCtl register and store it in cp0_fdc_irq where
platform implementations of the new weak platform function
get_c0_fdc_int() can refer to it.

[ralf@linux-mips.org: Fixed conflict.]
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9140/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      8f7ff027
    • J
      MIPS: Allow shared IRQ for timer & perf counter · 4a91d8fb
      由 James Hogan 提交于 
      Before release 2 of the architecture there weren't separate interrupt
pending bits for the local CPU interrupts (timer & perf counter
overflow), so when they were connected to the same interrupt line the
timer handler had to call the performance counter handler before knowing
whether a timer interrupt was actually pending.

Now another CPU local interrupt, for the Fast Debug Channel (FDC), can
also be routed to an arbitrary interrupt line. It isn't scalable to keep
adding cross-calls between handlers for these cases of shared interrupt
lines, especially since the FDC could in theory share its interrupt line
with the performance counter, timer, or both.

Fortunately since release 2 of the architecture separate interrupt
pending bits do exist in the Cause register. This allows local
interrupts which share an interrupt line to have separate handlers using
IRQF_SHARED. Unfortunately they can't easily have their own irqchip as
there is no generic way to individually mask them.

Enable this sharing to happen by removing the special case for when the
perf count shares an IRQ with the timer. cp0_perfcount_irq and
cp0_compare_irq can then be set to the same value with shared interrupt
handlers registered for both of them.

Pre-R2 code should be unaffected. cp0_perfcount_irq will always be -1
and the timer handler will contnue to call into the perf counter
handler.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9131/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      4a91d8fb
  11. 28 3月, 2015 2 次提交
    • J
      MIPS: Clear [MSA]FPE CSR.Cause after notify_die() · 64bedffe
      由 James Hogan 提交于 
      When handling floating point exceptions (FPEs) and MSA FPEs the Cause
bits of the appropriate control and status register (FCSR for FPEs and
MSACSR for MSA FPEs) are read and cleared before enabling interrupts,
presumably so that it doesn't have to go through the pain of restoring
those bits if the process is pre-empted, since writing those bits would
cause another immediate exception while still in the kernel.

The bits aren't normally ever restored again, since userland never
expects to see them set.

However for virtualisation it is necessary for the kernel to be able to
restore these Cause bits, as the guest may have been interrupted in an
FP exception handler but before it could read the Cause bits. This can
be done by registering a die notifier, to get notified of the exception
when such a value is restored, and if the PC was at the instruction
which is used to restore the guest state, the handler can step over it
and continue execution. The Cause bits can then remain set without
causing further exceptions.

For this to work safely a few changes are made:
- __build_clear_fpe and __build_clear_msa_fpe no longer clear the Cause
  bits, and now return from exception level with interrupts disabled
  instead of enabled.
- do_fpe() now clears the Cause bits and enables interrupts after
  notify_die() is called, so that the notifier can chose to return from
  exception without this happening.
- do_msa_fpe() acts similarly, but now actually makes use of the second
  argument (msacsr) and calls notify_die() with the new DIE_MSAFP,
  allowing die notifiers to be informed of MSA FPEs too.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
      64bedffe
    • P
      MIPS: Ensure FCSR cause bits are clear after invoking FPU emulator · ad70c13a
      由 Paul Burton 提交于 
      When running the emulator to handle an instruction that raised an FP
unimplemented operation exception, the FCSR cause bits were being
cleared. This is done to ensure that the kernel does not take an FP
exception when later restoring FP context to registers. However, this
was not being done when the emulator is invoked in response to a
coprocessor unusable exception. This happens in 2 cases:

  - There is no FPU present in the system. In this case things were
    OK, since the FP context is never restored to hardware registers
    and thus no FP exception may be raised when restoring FCSR.

  - The FPU could not be configured to the mode required by the task.
    In this case it would be possible for the emulator to set cause
    bits which are later restored to hardware if the task migrates
    to a CPU whose associated FPU does support its mode requirements,
    or if the tasks FP mode requirements change.

Consistently clear the cause bits after invoking the emulator, by moving
the clearing to process_fpemu_return and ensuring this is always called
before the tasks FP context is restored. This will make it easier to
catch further paths invoking the emulator in future, as will be
introduced in further patches.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9165/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      ad70c13a
  13. 05 3月, 2015 1 次提交
  15. 17 2月, 2015 3 次提交
  17. 16 2月, 2015 1 次提交
  19. 12 2月, 2015 1 次提交
    • P
      MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS · 9791554b
      由 Paul Burton 提交于 
      Userland code may be built using an ABI which permits linking to objects
that have more restrictive floating point requirements. For example,
userland code may be built to target the O32 FPXX ABI. Such code may be
linked with other FPXX code, or code built for either one of the more
restrictive FP32 or FP64. When linking with more restrictive code, the
overall requirement of the process becomes that of the more restrictive
code. The kernel has no way to know in advance which mode the process
will need to be executed in, and indeed it may need to change during
execution. The dynamic loader is the only code which will know the
overall required mode, and so it needs to have a means to instruct the
kernel to switch the FP mode of the process.

This patch introduces 2 new options to the prctl syscall which provide
such a capability. The FP mode of the process is represented as a
simple bitmask combining a number of mode bits mirroring those present
in the hardware. Userland can either retrieve the current FP mode of
the process:

  mode = prctl(PR_GET_FP_MODE);

or modify the current FP mode of the process:

  err = prctl(PR_SET_FP_MODE, new_mode);
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8899/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      9791554b
  21. 31 1月, 2015 1 次提交
    • J
      MIPS: traps: Fix inline asm ctc1 missing .set hardfloat · d76e9b9f
      由 James Hogan 提交于 
      Commit 842dfc11 ("MIPS: Fix build with binutils 2.24.51+") in v3.18
enabled -msoft-float and sprinkled ".set hardfloat" where necessary to
use FP instructions. However it missed enable_restore_fp_context() which
since v3.17 does a ctc1 with inline assembly, causing the following
assembler errors on Mentor's 2014.05 toolchain:

{standard input}: Assembler messages:
{standard input}:2913: Error: opcode not supported on this processor: mips32r2 (mips32r2) `ctc1 $2,$31'
scripts/Makefile.build:257: recipe for target 'arch/mips/kernel/traps.o' failed

Fix that to use the new write_32bit_cp1_register() macro so that ".set
hardfloat" is automatically added when -msoft-float is in use.

Fixes 842dfc11 ("MIPS: Fix build with binutils 2.24.51+")
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.18+, depends on "MIPS: mipsregs.h: Add write_32bit_cp1_register()"
Patchwork: https://patchwork.linux-mips.org/patch/9173/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      d76e9b9f
  23. 24 11月, 2014 4 次提交
  25. 02 8月, 2014 5 次提交
  27. 04 6月, 2014 1 次提交
  29. 25 5月, 2014 1 次提交
  31. 24 5月, 2014 1 次提交
    • R
      MIPS: MT: Remove SMTC support · b633648c
      由 Ralf Baechle 提交于 
      Nobody is maintaining SMTC anymore and there also seems to be no userbase.
Which is a pity - the SMTC technology primarily developed by Kevin D.
Kissell <kevink@paralogos.com> is an ingenious demonstration for the MT
ASE's power and elegance.

Based on Markos Chandras <Markos.Chandras@imgtec.com> patch
https://patchwork.linux-mips.org/patch/6719/ which while very similar did
no longer apply cleanly when I tried to merge it plus some additional
post-SMTC cleanup - SMTC was a feature as tricky to remove as it was to
merge once upon a time.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      b633648c
  33. 02 5月, 2014 1 次提交
  35. 27 3月, 2014 2 次提交