NFP is entirely programmable, including the PCI data interface.
Using a fixed control BAR layout certainly makes implementations
easier, but require careful considerations when space is allocated.
Once BAR area is allocated to one feature nothing else can use it.
Allocating space statically also requires it to be sized upfront,
which leads to either unnecessary limitation or wastage.

We currently have a 32bit capability word defined which tells drivers
which application FW features are supported.   Most of the bits
are exhausted.  The same bits are also reused for enabling specific
features.  Bulk of capabilities don't have a need for an enable bit,
however, leading to confusion and wastage.

TLVs seems like a better fit for expressing capabilities of applications
running on programmable hardware.

This patch leaves the front of the BAR as is, and declares a TLV
capability start at offset 0x58.  Most of the space up to 0x0d90
is already allocated, but the used space can be wrapped with RESERVED
TLVs.  E.g.:

Address    Type         Length
 0x0058    RESERVED      0xe00  /* Wrap basic structures */
 0x0e5c    FEATURE_A     0x004
 0x0e64    FEATURE_B     0x004
 0x0e6c    RESERVED      0x990  /* Wrap qeueue stats */
 0x1800    FEATURE_C     0x100
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver app matching loaded FW is not found users are faced with:

   nfp: failed to find app with ID 0x%02x

This message does not properly explain that matching driver code is
either not built into the driver or the driver is too old.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Representors are grouped in sets by type.  Currently the whole
sets are under RCU protection, but individual representor pointers
are not.  This causes some inconveniences when representors have
to be destroyed, because we have to allocate new sets to remove
any representors.  Protect the individual pointers with RCU.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The write side of repr tables is always done under pf->lock.
Add a helper to dereference repr table pointers under protection
of that lock.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Devlink used to have two global locks: devlink lock and port lock,
our lock ordering looked like this:

  devlink lock -> driver's pf->lock -> devlink port lock

After recent changes port lock was replaced with per-instance
lock.  Unfortunately, new per-instance lock is taken on most
operations now.  This means we can only grab the pf->lock from
the port split/unsplit ops.  Lock ordering looks like this:

  devlink lock -> driver's pf->lock -> devlink instance lock

Since we can't take pf->lock from most devlink ops, make sure
nfp_apps are prepared to service them as soon as devlink is
registered.  Locking the pf must be pushed down after
nfp_app_init() callback.

The init order looks like this:
 nfp_app_init
 devlink_register
 nfp_app_start
 netdev/port_register

As soon as app_init is done nfp_apps must be ready to service
devlink-related callbacks.  apps can only register their own
devlink objects from nfp_app_start.

Fixes: 2406e7e5 ("devlink: Add per devlink instance lock")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP app is currently shut down as soon as all the vNICs are gone.
This means we can't depend on the app existing throughout the
lifetime of the device.  Free the app only from PCI remove path.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the helpers for accessing 4 or 8 byte values over
the CPP bus return the length of IO on success.  If the IO
was short caller has to deal with error handling.  The short
IO for 4/8B values is completely impractical.  Make the
helpers return an error if full access was not possible.
Fix the few places which are actually dealing with errors
correctly, most call sites already only deal with negative
return codes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp: do not use RTT from delayed ACKs for min-RTT

This patch set prevents TCP sender from using RTT samples from
(suspected) delayed ACKs as the minimum RTT, to avoid unbounded
over-estimation of the network path delay. This issue is common
when a connection has extended periods of one packet chit-chat
beyond the min RTT filter window. The first patch does that for TCP
general min RTT estimation. The second patch addresses specifically
the BBR congestion control's min RTT filter.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A persistent connection may send tiny amount of data (e.g. health-check)
for a long period of time. BBR's windowed min RTT filter may only see
RTT samples from delayed ACKs causing BBR to grossly over-estimate
the path delay depending how much the ACK was delayed at the receiver.

This patch skips RTT samples that are likely coming from delayed ACKs. Note
that it is possible the sender never obtains a valid measure to set the
min RTT. In this case BBR will continue to set cwnd to initial window
which seems fine because the connection is thin stream.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NPriyaranjan Jha <priyarjha@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch avoids having TCP sender or congestion control
overestimate the min RTT by orders of magnitude. This happens when
all the samples in the windowed filter are one-packet transfer
like small request and health-check like chit-chat, which is farily
common for applications using persistent connections. This patch
tries to conservatively labels and skip RTT samples obtained from
this type of workload.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Letting tipc_poll() dereference a socket's pointer to struct tipc_group
entails a race risk, as the group item may be deleted in a concurrent
tipc_sk_join() or tipc_sk_leave() thread.

We now move the 'open' flag in struct tipc_group to struct tipc_sock,
and let the former retain only a pointer to the moved field. This will
eliminate the race risk.

Reported-by: syzbot+799dafde0286795858ac@syzkaller.appspotmail.com
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the switch block in l2tp_nl_cmd_session_create() that
checks pseudowire-specific parameters since just L2TP_PWTYPE_ETH and
L2TP_PWTYPE_PPP are currently supported and no actual checks are
performed. Moreover the L2TP_PWTYPE_IP/default case presents a harmless
issue in error handling (break instead of goto out_tunnel)
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

on T6, IPv6 filter would occupy 2 tids instead of 4.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lorenzo Bianconi says:

====================
l2tp: set l2specific_len based on l2specific_type

Do not rely on l2specific_len value provided by userspace but set sublayer
length according to l2specific_type.
Mark L2TP_ATTR_L2SPEC_LEN attribute as not used

Changes since v2:
- drop the patch related to a fix in the switch default case in
  l2tp_nl_cmd_session_create()
- use L2SPECTYPE_NONE as default case in l2tp_get_l2specific_len()

Changes since v1:
- remove l2specific_len parameter
- add sanity check on l2specific_type provided by userspace
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reviewed-by: NGuillaume Nault <g.nault@alphalink.fr>
Tested-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove l2specific_len configuration parameter since now L2-Specific
Sublayer length is computed according to l2specific_type provided by
userspace.
Reviewed-by: NGuillaume Nault <g.nault@alphalink.fr>
Tested-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove l2specific_len dependency while building l2tpv3 header or
parsing the received frame since default L2-Specific Sublayer is
always four bytes long and we don't need to rely on a user supplied
value.
Moreover in l2tp netlink code there are no sanity checks to
enforce the relation between l2specific_len and l2specific_type,
so sending a malformed netlink message is possible to set
l2specific_type to L2TP_L2SPECTYPE_DEFAULT (or even
L2TP_L2SPECTYPE_NONE) and set l2specific_len to a value greater than
4 leaking memory on the wire and sending corrupted frames.
Reviewed-by: NGuillaume Nault <g.nault@alphalink.fr>
Tested-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add sanity check on l2specific_type provided by userspace in
l2tp_nl_cmd_session_create() since just L2TP_L2SPECTYPE_DEFAULT and
L2TP_L2SPECTYPE_NONE are currently supported.
Moreover explicitly set l2specific_type to L2TP_L2SPECTYPE_DEFAULT
only if the userspace does not provide a value for it
Reviewed-by: NGuillaume Nault <g.nault@alphalink.fr>
Tested-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rahul Lakkireddy says:

====================
cxgb4: reduce memory footprint for collecting firmware dump

Firmware dump can be large (upto 2 GB).  In low memory conditions,
ethtool fails to allocate such large memory.  So, use zlib deflate
to compress collected firmware dump.

Patch 1 updates collection logic to use compression.

Patch 2 adds zlib deflate to compress collected firmware dump.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use zlib deflate to compress firmware dump. Collect and compress
as much firmware dump as possible into a 32 MB buffer.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NVishal Kulkarni <vishal@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update firmware dump collection logic to use compression when available.
Let collection logic attempt to do compression, instead of returning out
of memory early.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NVishal Kulkarni <vishal@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Helmut reported a bug about devision by zero while
running traffic and doing physical cable pull test.

When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is devision by zero.

This patch prevent this division for both ppms and epms.

Fixes: c3164d2f ("net/mlx5e: Added BW check for DIM decision mechanism")
Fixes: 4c4dbb4a ("net/mlx5e: Move dynamic interrupt coalescing code to include/linux")
Reported-by: NHelmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: NTalat Batheesh <talatb@mellanox.com>
Signed-off-by: NTal Gilboa <talgi@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

net/core/devlink.c:2297:25: warning:
 symbol 'devlink_resource_find' was not declared. Should it be static?
net/core/devlink.c:2322:6: warning:
 symbol 'devlink_resource_validate_children' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:289:5: warning:
 symbol 'mlxsw_sp_kvdl_part_occ' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable miistat is not used. So it is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 41033f02 ("snmp: Remove duplicate OUTMCAST stat
increment") one line of code became unneeded.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_KASAN is set, we can use relatively large amounts of kernel
stack space:

net/caif/cfctrl.c:555:1: warning: the frame size of 1600 bytes is larger than 1280 bytes [-Wframe-larger-than=]

This adds convenience wrappers around cfpkt_extr_head(), which is responsible
for most of the stack growth. With those wrapper functions, gcc apparently
starts reusing the stack slots for each instance, thus avoiding the
problem.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-4.16-20180119' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2018-01-16

this is a pull request for net-next/master consisting of 1 patch.

This patch by Arnd Bergmann for the m_can driver silences a compiler
warning if CONFIG_PM is not selected.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2018-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.16

Final few patches before the merge window, nothing really special.

ath9k

* add MSI support (not enabled by default yet)

rtlwifi

* support A-MSDU in A-MPDU aggregation
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building without CONFIG_PM results in a harmless warning:

drivers/net/can/m_can/m_can.c:1763:12: error: 'm_can_runtime_resume' defined but not used [-Werror=unused-function]
drivers/net/can/m_can/m_can.c:1752:12: error: 'm_can_runtime_suspend' defined but not used [-Werror=unused-function]

Marking the functions as __maybe_unused lets the compiler
silently drop them instead.

Fixes: cdf8259d ("can: m_can: Add PM Support")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

gcc-4.4.4 has problems witn anon union initializers.  Work around this.

net/sched/sch_prio.c: In function 'prio_dump_offload':
net/sched/sch_prio.c:260: error: unknown field 'stats' specified in initializer
net/sched/sch_prio.c:260: warning: initialization makes integer from pointer without a cast
net/sched/sch_prio.c:261: error: unknown field 'stats' specified in initializer
net/sched/sch_prio.c:261: warning: initialization makes integer from pointer without a cast

Fixes: 7fdb61b4 ("net: sch: prio: Add offload ability to PRIO qdisc")
Cc: Nogah Frankel <nogahf@mellanox.com>
Cc: Yuval Mintz <yuvalm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix removes unneeded semicolons after if blocks.

This issue was detected by using the Coccinelle software.
Signed-off-by: NChristopher Díaz Riveros <chrisadr@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: NLuis de Bethencourt <luisbg@kernel.org>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When tcm->tcm_ifindex == TCM_IFINDEX_MAGIC_BLOCK, parent is still passed
down but the value is never used. Compiler does not recognize it and
issues a warning. Silence it down initializing parent to 0.

Fixes: 7960d1da ("net: sched: use block index as a handle instead of qdisc when block is shared")
Reported-by: NDavid Miller <davem@davemloft.net>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to the fact that A-MSDU deaggregation is done in software,
we set this flag to support the A-MSDU in A-MPDU
Signed-off-by: NSteven Ting <steventing@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wil6210 maintainer email and mail list has changed, hence update
its MAINTAINERS entry accordingly.
Signed-off-by: NMaya Erez <merez@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'linux-can-next-for-4.16-20180116' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2018-01-16

this is a pull request for net-next/master consisting of 9 patches.

This is a series of patches, some of them initially by Franklin S Cooper
Jr, which was picked up by Faiz Abbas. Faiz Abbas added some patches
while working on this series, I contributed one as well.

The first two patches add support to CAN device infrastructure to limit
the bitrate of a CAN adapter if the used CAN-transceiver has a certain
maximum bitrate.

The remaining patches improve the m_can driver. They add support for
bitrate limiting to the driver, clean up the driver and add support for
runtime PM.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The trailing semicolon is an empty statement that does no operation.
It is completely stripped out by the compiler. Removing it since it doesn't do
anything.

Fixes: 5f35227e ("net: Generalize ndo_gso_check to ndo_features_check")
Signed-off-by: NLuis de Bethencourt <luisbg@kernel.org>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

restructure the code which adds support for configuring
PCIe VF via mgmt netdevice. which was added by
commit 7829451c ("cxgb4: Add control net_device for
configuring PCIe VF")

Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

idr_find() is safe under rcu_read_lock() and
maybe_get_net() guarantees that net is alive.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>