Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.

Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Adds support for the Samsung PATA controller. This driver is based
on the Libata subsystem and references the earlier patches sent for
IDE subsystem.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: NSergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch enables the on-chip DWC SATA controller of the AppliedMicro
processor 460EX.
Signed-off-by: NRupjyoti Sarmah <rsarmah@appliedmicro.com>
Signed-off-by: NMark Miesfeld <mmiesfeld@appliedmicro.com>
Signed-off-by: NProdyut Hazarika <phazarika@appliedmicro.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Make BMDMA optional depending on new config variable CONFIG_ATA_BMDMA.
In Kconfig, drivers are grouped into five groups - non-SFF native, SFF
w/ custom DMA interface, SFF w/ BMDMA, PIO-only SFF, and generic
fallback / legacy ones.  Kconfig and Makefile are reorganized
according to the groups and ordered alphabetically inside each group.

ata_ioports.bmdma_addr and ata_port.bmdma_prd[_dma] are put into
CONFIG_ATA_BMDMA, as are all bmdma related ops, variables and
functions.

This increase the binary size slightly when BMDMA is enabled but on
both native-only and PIO-only configurations the size is slightly
reduced.  Either way, the size difference is insignificant.  This
change is more meaningful to signify the separation between SFF and
BMDMA and as a tool to verify the separation.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sata_inic162x no longer uses SFF interface.  Move it out of
CONFIG_ATA_SFF.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This can be used for AHCI-compatible interfaces implemented inside
System-On-Chip solutions, or AHCI devices connected via localbus.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This is needed for some unsupported hardware setups on strange 64bit
mainboards where crazy stuff has been done like putting flash ata adapters
on the LPC bus, or where the real hardware is hidden/confused.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

In March 2008 commit 0ac4a3c2 ("ACPI: fix
ATA_ACPI build") made CONFIG_ACPI_DOCK be selected by CONFIG_ATA_ACPI because
of a build error when CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m.

However, in September 2008 commit 898b054f
("dock: make dock driver not a module") removed the possibility of having
CONFIG_ACPI_DOCK=m and therefore there is no need for selecting it when
CONFIG_ATA_ACPI=y.

This makes the kernel ~5 Kb smaller for people who don't have a dock by
allowing them to not have ACPI_DOCK compiled-in because of ATA_ACPI=y.
Signed-off-by: NCarlos R. Mafra <crmafra@aei.mpg.de>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c

It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.

The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NTejun Heo <tj@kernel.org>

We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.

As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: NJohn(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Reviewed-by: NGwendal Gringo <gwendal@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

From: Alan Cox <alan@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch improve libata's output for error/notification messages
to allow easier comprehension and debugging:

When ATAPI commands issued through the SCSI layer fail, use SCSI
functions to print the CDB in human-readable form instead of just
dumping out the CDB in hex.

Print out the name of the failed command (as defined by the ATA
specification) in error handling output along with the raw register
contents.

When reporting status of ACPI taskfile commands executed on resume,
also output the names of the commands being executed (or not) in
readable form.

Since the extra data for printing command names increases kernel
size slightly, a config option has been added to allow disabling
command name output (as well as some of the error register parsing)
for those highly sensitive to kernel text size.
Signed-off-by: NRobert Hancock <hancockrwd@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch provides PATA driver for CompactFlash interface in True IDE
mode on AT91SAM9260 SoC.
Signed-off-by: NSergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Support for Palm LifeDrive's internal harddrive.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Update Kconfig for sata_mv with full list of chips supported,
and (finally!) remove the "EXPERIMENTAL" designations.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.

Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported.  Although if DMA is
available, we do take advantage of it.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds MDMA/UDMA support using BestComm for DMA on the MPC5200
platform.  Based heavily on previous work by Freescale (Bernard Kuhn,
John Rigby) and Domen Puncer.

With this patch, a SanDisk Extreme IV CF card gets read speeds of
approximately 26.70 MB/sec.
Signed-off-by: NTim Yamin <plasm@roo.me.uk>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Various tags are now way out of date
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The RPC machine type now selects HAVE_PATA_PLATFORM so we can remove
the special case in the PATA_PLATFORM configuration code.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I've been chasing Jeff about this for months.  Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.

This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!

This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.

To quote Jeff in email

> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.

> See?  It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."

(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)

To quote Jeff in August 2007

> "   mv-ahci-pata
> Marvell 6121/6141 PATA support.  Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."

Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.

The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

While doing some easy cleanups on the sparc code I noticed that the
CONFIG_SUN4 code seems to be worse than the rest - there were some
"I don't know how it should work, but the current code definitely cannot
work." places.

And while I have seen people running Linux on machines like a
SPARCstation 5 a few years ago I don't recall having seen sun4
machines, even less ones running Linux.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add HAVE_PATA_PLATFORM to select the pata platform driver
to ensure that we do not end up with a long 'depends on' list
when other users of this driver turn up.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sata_inic162x is now ready for production use.  Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds Intel SCH chipsets (AF82US15W, AF82US15L, AF82UL11L)
PATA controller support.
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The platform is actually named routerboard 532 so let's call it this.  This
patch only rename files, Kconfig and C symbols; no functional changes.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set.  PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts.  This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.
Signed-off-by: NTejun Heo <htejun@gmail.com>

Now that SFF support is completely separated out from the core layer,
it can be made optional.  Add CONFIG_ATA_SFF and let SFF drivers
depend on it.  If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled.  This saves good
number of bytes for small systems.
Signed-off-by: NTejun Heo <htejun@gmail.com>

ATA_ACPI isn't selectable right now because it lacks 'short help
text'.  This means it's always enabled and always enables ACPI_DOCK.
Add text so it's now [de]selectable.

cc: Jeff Garzik <jeff@garzik.org>
cc: Tejun Heo <htejun@gmail.com>
cc: Len Brown <len.brown@intel.com>
Signed-off-by: NChris Wedgwood <cw@f00f.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

drivers/ata/libata-acpi.c fails to build

drivers/built-in.o: In function `ata_acpi_associate':
(.text+0x7106a): undefined reference to `register_hotplug_dock_device'

When CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m
But if dock is selected from ata_acpi, dock will =y
when ata_acpi=y, avoiding this problem.

http://bugzilla.kernel.org/show_bug.cgi?id=10272Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NJeff Garzik <jeff@garzik.org>

The integrated SATA controller is connected directly to the SoC's
internal bus, not via PCI interface. this patch removes the dependency
on the PCI interface.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The mpc8315 shares the same SATA controller as the mpc837x,
and likelihood is that future SoCs from Freescale will also.
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>