- 01 12月, 2010 6 次提交
-
-
由 David S. Miller 提交于
Now that all of the infrastructure is in place, we can add the ipv6 shorthand for peer creation. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Add the ipv6 peer tree instance, and adapt remaining direct references to 'v4_peers' as needed. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Now v4 and v6 addresses will both work properly. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
And make an inet_getpeer_v4() helper, update callers. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Currently only the v4 aspect is used, but this will change. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Instead of directly accessing "peer", change to code to operate using a "struct inet_peer_base *" pointer. This will facilitate the addition of a seperate tree for ipv6 peer entries. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 11月, 2010 15 次提交
-
-
由 Joe Perches 提交于
Use the normal debugging functions. Print mac address when using random_ether_addr. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
These were probably just for initial driver debugging and have not been enabled in builds in git history. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Use vsprintf extension %pM for a mac address in one instance. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Neaten the phy_init function by adding and calling vendor specific functions. object size is reduced by ~1kb: $ size drivers/net/forcedeth.o.* text data bss dec hex filename 83475 1848 19304 104627 198b3 drivers/net/forcedeth.o.new 84459 1848 19544 105851 19d7b drivers/net/forcedeth.o.old Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Deduplicate the code use for the init/reset of this device. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Use netdev_<level> when a struct net_device * is available. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Convert printks to pr_<level>. Remove "forcedeth: " from some calls as it's now added by pr_fmt. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
The remaining dprintk uses are emitted as KERN_INFO. Change these dprintk uses to netdev_dbg. Remove the now unused dprintk macros. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Use the standard code to emit hex dumps. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Use the more standard macro to preface netdev->name. Fix casting on resource use. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Move the printk out of reg_delay and make the callers emit a message on error. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
-
由 Eric Dumazet 提交于
Avoid sparse warnings : add __rcu annotations and use rcu_dereference_protected() where necessary. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Tom Herbert <therbert@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
store_xps_map() allocates maps that are used by single cpu, it makes sense to use NUMA allocations. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Tom Herbert <therbert@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shan Wei 提交于
1. SCTP_CMD_NUM_VERBS,SCTP_CMD_MAX These two macros have never been used for several years since v2.6.12-rc2. 2.sctp_port_rover,sctp_port_alloc_lock The commit 063930 abandoned global variables of port_rover and port_alloc_lock, but still keep two macros to refer to them. So, remove them now. commit 06393009 Author: Stephen Hemminger <shemminger@linux-foundation.org> Date: Wed Oct 10 17:30:18 2007 -0700 [SCTP]: port randomization Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 11月, 2010 19 次提交
-
-
由 Scott J. Goldman 提交于
If RSS is disabled, we can ifdef out some RSS specific code. This fixes the compile error found by Randy Dunlap. Signed-off-by: NScott J. Goldman <scottjg@vmware.com> Reviewed-by: NBhavesh Davda <bhavesh@vmware.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tom Herbert 提交于
This patch adds XPS_CONFIG option to enable and disable XPS. This is done in the same manner as RPS_CONFIG. This is also fixes build failure in XPS code when SMP is not enabled. Signed-off-by: NTom Herbert <therbert@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Frank Blaschka 提交于
The tso hdr is longer then the regular l3 hdr. Fix the calculation of the total len by accounting the size of the tso hdr. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
Device initialization of a qeth device contains a STARTLAN step. This step may fail, if cable is not yet plugged in. The qeth device stays in state HARDSETUP until cable is plugged in. This prevents further preparational initialization steps of the qeth device and its network interface. This patch makes sure initialization of qeth device continues, even though cable is not yet plugged in. Once carrier is available, qeth is notified, triggers a recovery which results in a working network interface. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sachin Sant 提交于
Commit 1d7138de igmp: RCU conversion of in_dev->mc_list converted rwlock to RCU. Update the s390 network drivers(qeth & lcs) code to adapt to this change. V2 : Changes based on suggestions given by Eric Dumazet Signed-off-by: NSachin Sant <sachinp@in.ibm.com> Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Giuseppe Cavallaro 提交于
The commit to convert to use the dev_pm_ops struct introduces a bug. The shutdown flag is not yet used because the hibernation on memory is done by using the freeze callback. Thanks to Vlad for having reported it. Reported-by: NVlad Lungu <vlad.lungu@windriver.com> Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Szymon Janc 提交于
Signed-off-by: NSzymon Janc <szymon@janc.net.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Szymon Janc 提交于
Signed-off-by: NSzymon Janc <szymon@janc.net.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Szymon Janc 提交于
forcedeth: include <linux/io.h> and <linux/uaccess.h> instead of <asm/io.h> and <asm/uaccess.h> as suggested by checkpatch Signed-off-by: NSzymon Janc <szymon@janc.net.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Szymon Janc 提交于
Signed-off-by: NSzymon Janc <szymon@janc.net.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Szymon Janc 提交于
Signed-off-by: NSzymon Janc <szymon@janc.net.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Breno Leitao 提交于
Currently the ret variable is not used for anything other than receive the value of the t3_adapter_error(), which will always be 0, because the reset parameter is 0. Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jozsef Kadlecsik 提交于
jhash is widely used in the kernel and because the functions are inlined, the cost in size is significant. Also, the new jhash functions are slightly larger than the previous ones so better un-inline. As a preparation step, the calls to the internal macros are replaced with the plain jhash function calls. Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Timo Teräs 提交于
fl->fl_gre_key is network byte order contrary to fl->fl_icmp_*. Make xfrm_flowi_{s|d}port return network byte order values for gre key too. Signed-off-by: NTimo Teräs <timo.teras@iki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-