- 17 11月, 2017 15 次提交
-
-
由 Maarten Lankhorst 提交于
The watermarks it should calculate against are the old optimal watermarks. The currently active crtc watermarks are pure fiction, and are invalid in case of a nonblocking modeset, page flip enabling/disabling planes or any other reason. When the crtc is disabled or during a modeset the intermediate watermarks don't need to be programmed separately, and could be directly assigned to the optimal watermarks. CXSR must always be disabled in the intermediate case for modesets, else we get a WARN for vblank wait timeout. Also rename crtc_state to new_crtc_state, to distinguish it from the old state. Changes since v1: - Use intel_atomic_get_old_crtc_state. (ville) Changes since v2: - Always unset cxsr during modeset. Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171115163157.14372-1-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
-
由 Maarten Lankhorst 提交于
Changes since v1: - Only pass crtc_state, not crtc. Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171110113503.16253-8-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
-
由 Maarten Lankhorst 提交于
IPS can only be enabled if the primary plane is visible, so first make sure sw state matches hw state by waiting for hw_done. After this pass crtc_state to intel_dp_sink_crc() so that can be used, instead of using legacy pointers. Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171110113503.16253-7-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
-
由 Maarten Lankhorst 提交于
The firmware may have set up the pipe correctly, but the FIFO underrun and CRC interrupts are likely not enabled. This resulted in debugfs_test.read_all_entries failing on haswell, because of a timeout when reading the crc debugfs entry. Solve this by enabling FIFO underrun reporting after the initial fastset, which lets interrupts be generated as expected. Changes since v1: - Always enable CPU FIFO underrun reporting for >GEN2, and handle GEN2 correctly. Changes since v2: - Remove unneeded HAS_DDI, simplify GEN2 case. Changes since v3: - Use intel_crtc_pch_transcoder to determine pch transcoder for underruns. (Ville) - Remove crtc->config dereference in intel_crtc_pch_transcoder. (Ville) Testcase: debugfs_test.read_all_entries Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171113144043.58658-1-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
-
由 Chris Wilson 提交于
Commit 21cc6431 ("drm/i915: Mark the userptr invalidate workqueue as WQ_MEM_RECLAIM") tried to fixup the check_flush_dependency warning for hitting i915_gem_userptr_mn_invalidate_range_start from within the shrinker, but I failed to notice userptr has 2 similarly named workqueues. I marked up i915-userptr-acquire as WQ_MEM_RECLAIM whereas we only wait upon i915-userptr-release from inside the reclaim paths. [62530.869510] workqueue: PF_MEMALLOC task 7983(gem_shrink) is flushing !WQ_MEM_RECLAIM i915-userptr-release: (null) [62530.869515] ------------[ cut here ]------------ [62530.869519] WARNING: CPU: 1 PID: 7983 at kernel/workqueue.c:2434 check_flush_dependency+0x7f/0x110 [62530.869519] Modules linked in: pegasus mii ip6table_filter ip6_tables bnep iptable_filter snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic binfmt_misc nls_iso8859_1 intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_intel snd_hda_codec kvm_intel snd_hda_core snd_hwdep kvm snd_pcm irqbypass snd_seq_midi snd_seq_midi_event snd_rawmidi crct10dif_pclmul crc32_pclmul 8250_dw ghash_clmulni_intel snd_seq pcbc snd_seq_device snd_timer btusb aesni_intel btrtl btbcm aes_x86_64 iwlwifi btintel crypto_simd glue_helper cryptd bluetooth snd intel_cstate input_leds idma64 intel_rapl_perf ecdh_generic serio_raw soundcore cfg80211 wmi_bmof virt_dma intel_lpss_pci intel_lpss acpi_als kfifo_buf industrialio winbond_cir soc_button_array rc_core spidev tpm_crb intel_hid acpi_pad mac_hid sparse_keymap [62530.869546] parport_pc ppdev lp parport ip_tables x_tables autofs4 hid_generic usbhid i915 i2c_algo_bit prime_numbers drm_kms_helper syscopyarea e1000e sysfillrect sysimgblt fb_sys_fops ahci ptp pps_core libahci drm wmi video i2c_hid hid [62530.869557] CPU: 1 PID: 7983 Comm: gem_shrink Tainted: G U W L 4.14.0-rc8-drm-tip-ww45-commit-1342299+ #1 [62530.869558] Hardware name: Intel Corporation CoffeeLake Client Platform/CoffeeLake H DDR4 RVP, BIOS CNLSFWR1.R00.X098.A00.1707301945 07/30/2017 [62530.869559] task: ffffa1049dbeec80 task.stack: ffffae7d05c44000 [62530.869560] RIP: 0010:check_flush_dependency+0x7f/0x110 [62530.869561] RSP: 0018:ffffae7d05c473a0 EFLAGS: 00010286 [62530.869562] RAX: 000000000000006e RBX: ffffa1049540f400 RCX: ffffffffa3e55788 [62530.869562] RDX: 0000000000000000 RSI: 0000000000000092 RDI: 0000000000000202 [62530.869563] RBP: ffffae7d05c473c0 R08: 000000000000006e R09: 000000000038bb0e [62530.869563] R10: 0000000000000000 R11: 000000000000006e R12: ffffa1049dbeec80 [62530.869564] R13: 0000000000000000 R14: 0000000000000000 R15: ffffae7d05c473e0 [62530.869565] FS: 00007f621b129880(0000) GS:ffffa1050b240000(0000) knlGS:0000000000000000 [62530.869566] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [62530.869566] CR2: 00007f6214400000 CR3: 0000000353a17003 CR4: 00000000003606e0 [62530.869567] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [62530.869567] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [62530.869568] Call Trace: [62530.869570] flush_workqueue+0x115/0x3d0 [62530.869573] ? wake_up_process+0x15/0x20 [62530.869596] i915_gem_userptr_mn_invalidate_range_start+0x12f/0x160 [i915] [62530.869614] ? i915_gem_userptr_mn_invalidate_range_start+0x12f/0x160 [i915] [62530.869616] __mmu_notifier_invalidate_range_start+0x55/0x80 [62530.869618] try_to_unmap_one+0x791/0x8b0 [62530.869620] ? call_rwsem_down_read_failed+0x18/0x30 [62530.869622] rmap_walk_anon+0x10b/0x260 [62530.869624] rmap_walk+0x48/0x60 [62530.869625] try_to_unmap+0x93/0xf0 [62530.869626] ? page_remove_rmap+0x2a0/0x2a0 [62530.869627] ? page_not_mapped+0x20/0x20 [62530.869629] ? page_get_anon_vma+0x90/0x90 [62530.869630] ? invalid_mkclean_vma+0x20/0x20 [62530.869631] migrate_pages+0x946/0xaa0 [62530.869633] ? __ClearPageMovable+0x10/0x10 [62530.869635] ? isolate_freepages_block+0x3c0/0x3c0 [62530.869636] compact_zone+0x22f/0x970 [62530.869638] compact_zone_order+0xa3/0xd0 [62530.869640] try_to_compact_pages+0x1a5/0x2a0 [62530.869641] ? try_to_compact_pages+0x1a5/0x2a0 [62530.869643] __alloc_pages_direct_compact+0x50/0x110 [62530.869644] __alloc_pages_slowpath+0x4da/0xf30 [62530.869646] __alloc_pages_nodemask+0x262/0x280 [62530.869648] alloc_pages_vma+0x165/0x1e0 [62530.869649] shmem_alloc_hugepage+0xd0/0x130 [62530.869651] ? __radix_tree_insert+0x45/0x230 [62530.869652] ? __vm_enough_memory+0x29/0x130 [62530.869654] shmem_alloc_and_acct_page+0x10d/0x1e0 [62530.869655] shmem_getpage_gfp+0x426/0xc00 [62530.869657] shmem_fault+0xa0/0x1e0 [62530.869659] ? file_update_time+0x60/0x110 [62530.869660] __do_fault+0x1e/0xc0 [62530.869661] __handle_mm_fault+0xa35/0x1170 [62530.869662] handle_mm_fault+0xcc/0x1c0 [62530.869664] __do_page_fault+0x262/0x4f0 [62530.869666] do_page_fault+0x2e/0xe0 [62530.869667] page_fault+0x22/0x30 [62530.869668] RIP: 0033:0x404335 [62530.869669] RSP: 002b:00007fff7829e420 EFLAGS: 00010216 [62530.869670] RAX: 00007f6210400000 RBX: 0000000000000004 RCX: 0000000000b80000 [62530.869670] RDX: 0000000000002e01 RSI: 0000000000008000 RDI: 0000000000000004 [62530.869671] RBP: 0000000000000019 R08: 0000000000000002 R09: 0000000000000000 [62530.869671] R10: 0000000000000559 R11: 0000000000000246 R12: 0000000008000000 [62530.869672] R13: 00000000004042f0 R14: 0000000000000004 R15: 000000000000007e [62530.869673] Code: 00 8b b0 18 05 00 00 48 8d 8b b0 00 00 00 48 8d 90 c0 06 00 00 4d 89 f0 48 c7 c7 40 c0 c8 a3 c6 05 68 c5 e8 00 01 e8 c2 68 04 00 <0f> ff 4d 85 ed 74 18 49 8b 45 20 48 8b 70 08 8b 86 00 01 00 00 [62530.869691] ---[ end trace 01e01ad0ff5781f8 ]--- Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103739 Fixes: 21cc6431 ("drm/i915: Mark the userptr invalidate workqueue as WQ_MEM_RECLAIM") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Michał Winiarski <michal.winiarski@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171114173520.8829-1-chris@chris-wilson.co.ukReviewed-by: NMatthew Auld <matthew.auld@intel.com>
-
由 Chris Wilson 提交于
We should long past the time of trying to use wait_for() from inside atomic contexts, so add a might_sleep() check to prevent misuse. Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171114215655.4849-1-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
-
由 Michel Thierry 提交于
The first test aims to check guc_init_doorbell_hw, changing the existing guc clients and doorbells state before calling it. The second test tries to create as many clients as it is currently possible (currently limited to max number of doorbells) and exercise the doorbell alloc/dealloc code. Since our usage mode require very few clients/doorbells, this code has been exercised very lightly and it's good to have a simple test for it. As reference, this test already helped identify the bug fixed by commit 7f1ea2ac ("drm/i915/guc: Fix doorbell id selection"). v2: Extend number of clients; check for client allocation failure when number of doorbells is exceeded; validate client properties; reuse guc_init_doorbell_hw (Chris). v3: guc_init_doorbell_hw test added per Chris suggestion. v4: Try to explain why guc_init_doorbell_hw exist and comment some details in the subtest. v5: Remove redundant pr_info at the beginning of each subtest (Chris); rebase (s/i915_guc_client/intel_guc_client/). Signed-off-by: NMichel Thierry <michel.thierry@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20171116220632.1909-1-michel.thierry@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>
-
https://github.com/intel/gvt-linux由 Rodrigo Vivi 提交于
gvt-next-2017-11-16 - CSB HWSP update support (Weinan) - GVT debug helpers, dyndbg and debugfs (Chuanxiao, Shuo) - full virtualized opregion (Xiaolin) - VM health check for sane fallback (Fred) - workload submission code refactor for future enabling (Zhi) - Updated repo URL in MAINTAINERS (Zhenyu) - other many misc fixes Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171116092007.ww5bvfx7rf36bjmn@zhen-hp.sh.intel.com
-
由 Rodrigo Vivi 提交于
Starting on GLK we support HDMI 2.0. So this patch only extend the work Shashank has made to GLK to CNL. v2: The version that compiles :/ v3: Invert order to newer || older platforms check. (Ville). Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171115184205.8104-1-rodrigo.vivi@intel.com
-
由 Rodrigo Vivi 提交于
I confess I never fully understood that previous calculation, so this is not a "fix". But let's simplify this math so poor brains like mine can read and make some sense of it in the future. v2: Don't follow the spec since that gives invalid values and it is also confusing. This Ville's version is much simpler. v3: Use u64 cast instead of declaring a u64 dco. (Ville). Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: James Ausmus <james.ausmus@intel.com> Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171115184257.8633-1-rodrigo.vivi@intel.com
-
由 Rodrigo Vivi 提交于
Accordingly to spec "If Kdiv != 2, then Qdiv must be 1." but we already handle qdiv values properly and this case here should be spurious. But instead of blindly replacing let's warn loudly instead. Because it means something was really wrong on initial setup. Cc: Mika Kahola <mika.kahola@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: James Ausmus <james.ausmus@intel.com> Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: NManasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-6-rodrigo.vivi@intel.com
-
由 Rodrigo Vivi 提交于
Spec describe all values in MHz. We handle our clocks in KHz. This includes the best_dco_centrality that was forgot in the same unity as spec. Consequently we couldn't get a good divider for high frequenies. Hence HDMI 2.0 wasn't working. Spec tells 999999 for initial best_dco_centrality meaning the max value in MHz. Since we convert dco from MHz to KHz we also need to convert this initial best_doc_centrality to 999999000 or 999999999 or even better, to the max that its variable allow. This patch also replaces the use of "* KHz(1)" with the values directly on KHz to avoid future confusion. v2: Use U32_MAX instead of random 99999 as spec tells. (Ville). Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: James Ausmus <james.ausmus@intel.com> Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171114234223.10600-1-rodrigo.vivi@intel.com
-
由 Rodrigo Vivi 提交于
- 64 bits is not needed for afe_clock now we don't convert that to Hz. - 16 bits is not enough for all dco stuff. - unsigned is not relevant/needed for all divisors values. Cc: Mika Kahola <mika.kahola@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: James Ausmus <james.ausmus@intel.com> Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Manasi Navare <manasi.d.navare@intel.com Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-4-rodrigo.vivi@intel.com
-
由 Rodrigo Vivi 提交于
No functional change. Just starting the wrpll fixes with a clean-up to make units a bit more clear. Cc: Mika Kahola <mika.kahola@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: James Ausmus <james.ausmus@intel.com> Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: NManasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-3-rodrigo.vivi@intel.com
-
由 Rodrigo Vivi 提交于
"Display software must leave this field at the default value. It no longer needs to be configured as part of PLL programming." We respect this already and we are setting up the default one line below: "DPLL_CFGCR1_CENTRAL_FREQ". Also we don't touch anywhere else this central_freq for cnl. So let's remove from the final write. No functional change. Only a clean-up patch. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Cc: James Ausmus <james.ausmus@intel.com> Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: NManasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171114194759.24541-2-rodrigo.vivi@intel.com
-
- 16 11月, 2017 25 次提交
-
-
由 Chris Wilson 提交于
When operating on the live_ggtt we have to find a usuable hole for our test. It is possible for there to be no hole we can use, so initialise the err to 0 for the early exit. Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20171115152558.31252-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
由 Ville Syrjälä 提交于
Avoid touching PIPECONF in intel_sanitize_crtc() unless the pipe is actually on. Should cure some unclaimed register accesses during reset, as we are rather cavalier in our approach to powerdomain management. We don't have to sanitize this if the pipe is off since we will overwrite the frame start delay anyway when turning the pipe on. v2: Amended commit message to implicate the reset path (Chris) Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102249Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171115200442.15051-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
-
由 Sagar Arun Kamble 提交于
With all component structures and functions named appropriately, change the names of GuC submission source files. There were bunch of style issues in guc_submission.c that are highlighted now by checkpatch. Fix those. Update name in Documentation/gpu. (Joonas) v2: Rebase. v3: Rebase. Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michal Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: NChris Wilson <chris@chris-wilson.co.uk> Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: NOscar Mateo <oscar.mateo@intel.com> Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1510839162-25197-6-git-send-email-sagar.a.kamble@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>
-
由 Sagar Arun Kamble 提交于
GuC submission clients are currently being used in kernel only hence update the structure name to intel_guc_client. Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michal Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: NChris Wilson <chris@chris-wilson.co.uk> Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: NOscar Mateo <oscar.mateo@intel.com> Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1510839162-25197-5-git-send-email-sagar.a.kamble@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>
-
由 Sagar Arun Kamble 提交于
i915 GuC submission is hardware interface and GuC APIs that are not user facing should be named intel_guc* hence we change GuC submission related functions name prefix to intel_guc. Also changed the parameter to these functions to intel_guc struct. v2: Using local guc variable in intel_uc_fini_hw. (Michal Wajdeczko) Rebase. Suggested-by: NChris Wilson <chris@chris-wilson.co.uk> Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michal Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: NChris Wilson <chris@chris-wilson.co.uk> Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: NOscar Mateo <oscar.mateo@intel.com> Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1510839162-25197-4-git-send-email-sagar.a.kamble@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>
-
由 Sagar Arun Kamble 提交于
i915_guc_submit, i915_guc_dequeue, i915_guc_submission_park and i915_guc_submission_upark are functions internal to GuC submission hence remove "i915_" prefix. Suggested-by: NMichal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michal Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1510839162-25197-3-git-send-email-sagar.a.kamble@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>
-
由 Sagar Arun Kamble 提交于
intel_lrc_irq_handler and i915_guc_irq_handler are HW submission related tasklet functions. Name them with "submission_tasklet" suffix and remove intel/i915 prefix as they are static. Also rename irq_tasklet as just tasklet for clarity. v2: s/_bh/_tasklet (Chris) Suggested-by: NMichal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michal Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/1510839162-25197-2-git-send-email-sagar.a.kamble@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>
-
由 Chris Wilson 提交于
We check whether the multiplies will overflow prior to calling kmalloc_array so that we can respond with -EINVAL for the invalid user arguments rather than treating it as an -ENOMEM that would otherwise occur. However, as Dan Carpenter pointed out, we did an addition on the unsigned int prior to passing to kmalloc_array where it would be promoted to size_t for the calculation, thereby allowing it to overflow and underallocate. v2: buffer_count is currently limited to INT_MAX because we treat it as signaled variable for LUT_HANDLE in eb_lookup_vma v3: Move common checks for eb1/eb2 into the same function v4: Put the check back for nfence*sizeof(user_fence) overflow v5: access_ok uses ULONG_MAX but kvmalloc_array uses SIZE_MAX v6: size_t and unsigned long are not type-equivalent on 32b Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171116105059.25142-1-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
-
由 Chris Wilson 提交于
When we call intel_engine_cancel_signaling() to stop reporting when a request is completed via an asynchronous signal, we remove that request from the breadcrumb wait queue. However, we may be concurrently processing that request in the signaler itself, the actual operations on the request's node itself are serialised but we do not actually clear the waiter after removing it from the tree allowing both parties to attempt to do so and corrupting the rbtree. (Previously removing from the breadcrumb wait queue could only be done on behalf of i915_wait_request, so this race could not happen). Reported-by: N"He, Bo" <bo.he@intel.com> Fixes: 9eb143bb ("drm/i915: Allow a request to be cancelled") Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: "He, Bo" <bo.he@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171115121458.24655-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
由 Mika Kuoppala 提交于
It is easier to categorize and debug bugs if the failed condition is in plain sight in the actual dmesg output. Make it so. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Marta Lofstedt <marta.lofstedt@intel.com> Signed-off-by: NMika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: NMarta Lofstedt <marta.lofstedt@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171116083954.3357-1-mika.kuoppala@linux.intel.com
-
由 fred gao 提交于
Previously the performance is improved through the workload auditing and shadowing ahead of vGPU scheduling, however, there is the case that more requests are allocated in submit_context before the previous request is added, the timeline will hold its seqno which is later. This patch is to move the request alloc to dispatch_workload function, where is the same place as request is added. It will fix the issue of kernel BUG for (timeline->seqno != request->fence.seqno) check when add_request. Fixes: 89ea20b9 ("drm/i915/gvt: Factor out scan and shadow from workload dispatch") Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Nfred gao <fred.gao@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Xiong Zhang 提交于
Currently every vgpu share a common gvt opregion memory, but it is freed at vgpu destroy, then the later vgpu doesn't have opregion memory once the first vgpu is destroyed. This cause guest function failure like reboot, second or later boot. This patch allocate and init virt opregion memory for each vgpu, so this memory could be freed at vgpu destroy. Signed-off-by: NXiong Zhang <xiong.y.zhang@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Xiong Zhang 提交于
mmio_read_from_hw() let vgpu could read hw reg, if vgpu's workload is running on hw, things is good. Otherwise vgpu will get other vgpu's reg val, it is unsafe. This patch limit such hw access to active vgpu. If vgpu isn't running on hw, the reg read of this vgpu will get the last active val which saved at schedule_out. v2: ring timestamp is walking continuously even if the ring is idle. so read hw directly. (Zhenyu) Signed-off-by: NXiong Zhang <xiong.y.zhang@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Zhenyu Wang 提交于
This reverts commit b20d09886fd1b74cd2255d846029a049e524db14. This caused windows driver boot errors for invalid page address. Revert for now. Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com> Cc: Zhi Wang <zhi.a.wang@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Changbin Du 提交于
Our vGPU doesn't have a device ROM, we need follow the PCI spec to report this info to drivers. Otherwise, we would see below errors. Inspecting possible rom at 0xfe049000 (vd=8086:1912 bdf=00:10.0) qemu-system-x86_64: vfio-pci: Cannot read device rom at 00000000-0000-0000-0000-000000000001 Device option ROM contents are probably invalid (check dmesg). Skip option ROM probe with rombar=0, or load from file with romfile=No option rom signature (got 4860) I will also send a improvement patch to PCI subsystem related to PCI ROM. But no idea to omit below error, since no pattern to detect vbios shadow without touch its content. 0000:00:10.0: Invalid PCI ROM header signature: expecting 0xaa55, got 0x0000 Signed-off-by: NChangbin Du <changbin.du@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Changbin Du 提交于
gvt_vgpu_err means something goes wrong. We need the error propagates to kernel message by default. Signed-off-by: NChangbin Du <changbin.du@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Changbin Du 提交于
I have seen the cmd parser dump partial odd info. Stop that and only dump the full verbose info when debug enabled. Signed-off-by: NChangbin Du <changbin.du@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Changbin Du 提交于
Use I915_WRITE_FW instead of I915_WRITE to reduce overhead. The overall mmio switch latency lowers from ~600us to ~180us. Signed-off-by: NChangbin Du <changbin.du@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Zhenyu Wang 提交于
gvt-linux.git repo is moved for its new place under https://github.com/intel/gvt-linux.git Old https://github.com/01org/gvt-linux.git is set only for redirect now. Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Changbin Du 提交于
This new debugfs entry is used to figure out which registers of vGPU is different to host. It is a useful tool for new platform enabling and debugging. When read this entry, all the diff mmio are recognized and sorted by mmio offset. Besides, the bit positions of different value are listed in 'Diff' column. Here is a show: $ sudo cat ./mmio_diff Offset HW vGPU Diff 00002030 000025f8 00000000 3-8,10,13 00002034 012025f8 00000000 3-8,10,13,21,24 00002038 027fb000 00000000 12-13,15-22,25 0000203c 00003000 00000000 12-13 00002054 0000000a 00000040 1,3,6 00002074 012025f8 00000000 3-8,10,13,21,24 00002080 fffe6000 00000000 13-14,17-31 000020a8 fffffeff ffffffff 8 000020d4 00000004 00000000 2 .... 00145974 eb42718c 010c11b0 2-5,13-14,17-19,22,25,27,29-31 00145978 0000002f 0000002a 0,2 0014597c 0000002f 0000002a 0,2 00145980 0000002b 00000028 0-1 00145984 a5a87c9e b27d20c0 1-4,6,10-12,14,16,18,20,22-26,28 001459c0 88390000 883c0000 16,18 00146200 88350000 883a0000 16-19 Total: 72432, Diff: 901 v3: fix a typo. v2: add mmio_hw_access_pre/post(). Signed-off-by: NChangbin Du <changbin.du@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Changbin Du 提交于
This patch add a function intel_gvt_for_each_tracked_mmio() to iterate each tracked mmio. The caller don't be aware of how the tracked mmios are presented internally. v2: remove snapshot_hw_mmio_registers(). Signed-off-by: NChangbin Du <changbin.du@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Xiaolin Zhang 提交于
this is an enhanced opregion emulation for win guest support by initializing more data members including opregion header size, version and child device propertity for display port. for simplicity, redefined child_device_config structure. Signed-off-by: NXiaolin Zhang <xiaolin.zhang@intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Weinan Li 提交于
The engine provides a mirror of the CSB and CSB write pointer in the HWSP. Read these status from virtual HWSP in VM can reduce CPU utilization while applications have much more short GPU workloads. Here we update the corresponding data in virtual HWSP as it in virtual MMIO. Before read these status from HWSP in GVT-g VM, please ensure the host support it by checking the BIT(3) of caps in PVINFO. Virtual HWSP only support GEN8+ platform, since the HWSP MMIO may change follow the platform update, please add the corresponding MMIO emulation when enable new platforms in GVT-g. v3 : Add address audit in HWSP address update. v4 : Separate this patch with enalbe virtual HWSP in VM. Use intel_gvt_render_mmio_to_ring_id() to determine ring_id by offset. v5 : Remove unnessary check about Gen8, GVT-g only support Gen8+. Signed-off-by: NWeinan Li <weinan.z.li@intel.com> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
-
由 Zhi Wang 提交于
Refine previously broken PPGTT scratch. Scratch PTE was no correctly handled and also the handling of scratch entries in page table walk was not well organized, which brings gaps of introducing lazy shadow. Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
-
由 Zhi Wang 提交于
We need ops->set_present() during generating a new scratch page table entry. Signed-off-by: NZhi Wang <zhi.a.wang@intel.com>
-