This change is a fix of the macvlan offload so that we correctly handle
macvlan offloaded devices. Specifically we were configuring our limits based
on the assumption that we were going to max out the RSS indices for every
mode. As a result when we went to 15 or more macvlan interfaces we were
forced into the 2 queue RSS mode on VFs even though they could have still
supported 4.

This change splits the logic up so that we limit either the total number of
macvlan instances if DCB is enabled, or limit the number of RSS queues used
per macvlan (instead of per pool) if SR-IOV is enabled. By doing this we
can make best use of the part.

In addition I have increased the maximum number of supported interfaces to
63 with one queue per offloaded interface as this more closely reflects the
actual values supported by the interface.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The num_rx_pools value is overwritten when we reinitialize the queue
configuration. In reality we shouldn't need to be updating the value since
it is redone every time we call into ixgbe_setup_tc so for now just drop
the spots where we were incrementing or decrementing the value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order for RSS to work on the macvlan pools of the X550 we need to
populate the MRQC, RETA, and RSS key values for each pool. This patch makes
it so that we now take care of that.

In addition I have dropped the macvlan specific configuration of psrtype
since it is redundant with the code that already exists for configuring
this value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the number of VFs are changed we need to reinitialize the part since the
offset for the device and the number of pools will be incorrect. Without
this change we can end up seeing Tx hangs and dropped Rx frames for
incoming traffic.

In addition we should drop the code that is arbitrarily changing the
default pool and queue configuration. Instead we should wait until the port
is reset and reconfigured via ixgbe_sriov_reinit.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When SR-IOV was enabled the macvlan offload was configuring several filters
with the wrong pool value. This would result in the macvlan interfaces not
being able to receive traffic that had to pass over the physical interface.

To fix it wrap the pool argument in the VMDQ_P macro which will add the
necessary offset to get to the actual VMDq pool
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removed leftover assignment of xcast_mode.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The InterruptThrottleRate has been removed from ixgbe. Then Update
the comment.
Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Extend FW version reporting by displaying information from the iSCSI
or OEM block in the EEPROM.

This will allow us to more accurately identify the FW.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On module insert advertise highest capable link speed. If module is
capable of 10G, then advertise 10G, else advertise modules capable
link speeds.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This enum is no longer needed after
commit: b4ded832 ("ixgbe: Update adaptive ITR algorithm")
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we only enabled the reception of multicast packets when
wake on multicast is set, but we also need this to allow waking with
IPv6 magic packets.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by TIPC at all.

So, remove the unused hardirq.h.
Signed-off-by: NYang Shi <yang.s@alibaba-inc.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Tested-by: NYing Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by openvswitch at all.

So, remove the unused hardirq.h.
Signed-off-by: NYang Shi <yang.s@alibaba-inc.com>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: dev@openvswitch.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by caif at all.

So, remove the unused hardirq.h.
Signed-off-by: NYang Shi <yang.s@alibaba-inc.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gal Pressman says:

====================
Replace WARN_ONCE usages with netdev_WARN_ONCE

This series will fix an issue in netdev_WARN_ONCE, improve its formatting and
replace drivers' usage of WARN_ONCE to netdev_WARN_ONCE.

Driver specific patches were compilation tested, in addition, functional tested
on Mellanox NIC.

v1->v2:
- Addressed commit message comments in patch #1
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the unnecessary line break between the netdev name and reg state
to the actual message that should be printed.

For example, this:
[86730.307236] ------------[ cut here ]------------
[86730.313496] netdevice: enp27s0f0
Message from the driver
[...]

Will be replaced with:
[86770.259289] ------------[ cut here ]------------
[86770.265191] netdevice: enp27s0f0: Message from the driver
[...]
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_WARN_ONCE is broken (whoops..), this fix will remove the
unnecessary "condition" parameter, add the missing comma and change
"arg" to "args".

Fixes: 375ef2b1 ("net: Introduce netdev_*_once functions")
Signed-off-by: NGal Pressman <galp@mellanox.com>
Reviewed-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for your
net-next tree:

1) Free hooks via call_rcu to speed up netns release path, from
   Florian Westphal.

2) Reduce memory footprint of hook arrays, skip allocation if family is
   not present - useful in case decnet support is not compiled built-in.
   Patches from Florian Westphal.

3) Remove defensive check for malformed IPv4 - including ihl field - and
   IPv6 headers in x_tables and nf_tables.

4) Add generic flow table offload infrastructure for nf_tables, this
   includes the netlink control plane and support for IPv4, IPv6 and
   mixed IPv4/IPv6 dataplanes. This comes with NAT support too. This
   patchset adds the IPS_OFFLOAD conntrack status bit to indicate that
   this flow has been offloaded.

5) Add secpath matching support for nf_tables, from Florian.

6) Save some code bytes in the fast path for the nf_tables netdev,
   bridge and inet families.

7) Allow one single NAT hook per point and do not allow to register NAT
   hooks in nf_tables before the conntrack hook, patches from Florian.

8) Seven patches to remove the struct nf_af_info abstraction, instead
   we perform direct calls for IPv4 which is faster. IPv6 indirections
   are still needed to avoid dependencies with the 'ipv6' module, but
   these now reside in struct nf_ipv6_ops.

9) Seven patches to handle NFPROTO_INET from the Netfilter core,
   hence we can remove specific code in nf_tables to handle this
   pseudofamily.

10) No need for synchronize_net() call for nf_queue after conversion
    to hook arrays. Also from Florian.

11) Call cond_resched_rcu() when dumping large sets in ipset to avoid
    softlockup. Again from Florian.

12) Pass lockdep_nfnl_is_held() to rcu_dereference_protected(), patch
    from Florian Westphal.

13) Fix matching of counters in ipset, from Jozsef Kadlecsik.

14) Missing nfnl lock protection in the ip_set_net_exit path, also
    from Jozsef.

15) Move connlimit code that we can reuse from nf_tables into
    nf_conncount, from Florian Westhal.

And asorted cleanups:

16) Get rid of nft_dereference(), it only has one single caller.

17) Add nft_set_is_anonymous() helper function.

18) Remove NF_ARP_FORWARD leftover chain definition in nf_tables_arp.

19) Remove unnecessary comments in nf_conntrack_h323_asn1.c
    From Varsha Rao.

20) Remove useless parameters in frag_safe_skb_hp(), from Gao Feng.

21) Constify layer 4 conntrack protocol definitions, function
    parameters to register/unregister these protocol trackers, and
    timeouts. Patches from Florian Westphal.

22) Remove nlattr_size indirection, from Florian Westphal.

23) Add fall-through comments as -Wimplicit-fallthrough needs this,
    from Gustavo A. R. Silva.

24) Use swap() macro to exchange values in ipset, patch from
    Gustavo A. R. Silva.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of now, there're two sk_family are traced with sock:inet_sock_set_state,
which are AF_INET and AF_INET6.
So the sk_family are exposed as well.
Then we can conveniently use it to do the filter.

Both sk_family and sk_protocol are showed in the printk message, so we need
not expose them as tracepoint arguments.
Suggested-by: NBrendan Gregg <brendan.d.gregg@gmail.com>
Suggested-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Reviewed-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "offset" option has been removed by
commit 900631ee ("l2tp: remove configurable payload offset").
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Acked-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mask argument for phy_modify() in several locations was inverted.

Fixes: fea23fb5 ("net: phy: convert read-modify-write to phy_modify()")
Reported-by: NHeiner Kallweit <hkallweit1@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since both first_rx and rx_ring are the head of rx ring, it not
necessary to use two structure members to statically indicate
the head of rx ring. So first_rx is removed.

CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two conditions triggering BUG_ON() are somewhat unrelated:
the tcp_skb_pcount() check is meant to catch TSO flaws, the
second one checks sanity of congestion window bookkeeping.

Split them into two separate BUG_ON() assertions on two lines,
so that we know which one actually triggers, when they do.
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow a process bound to a VRF to connect to a linklocal address.
Currently, this fails because of a mismatch between the scope of the
linklocal address and the sk_bound_dev_if inherited by the VRF binding:
    $ ssh -6 fe80::70b8:cff:fedd:ead8%eth1
    ssh: connect to host fe80::70b8:cff:fedd:ead8%eth1 port 22: Invalid argument

Relax the scope check to allow the socket to be bound to the same L3
device as the scope id.

This makes ipv6 linklocal consistent with other relaxed checks enabled
by commits 1ff23bee ("net: l3mdev: Allow send on enslaved interface")
and 7bb387c5 ("net: Allow IP_MULTICAST_IF to set index to L3 slave").
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the commit 888cc8c2 ("sh_eth: remove EDMAC_BIG_ENDIAN") (geez,
I didn't realize that was 2 years ago!) the initializers in the SuperH
platform code for the 'sh_eth_plat_data::edmac_endian' stopped to matter,
so we can remove that field for good (not sure if  it  was ever useful --
SH7786 Ether has been reported  to have the same EDMAC descriptor/register
endiannes as configured for the SuperH CPU)...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Peng Li says:

====================
add some new features and fix some bugs for HNS3 driver

This patchset adds some new features support and fixes some bugs:
[Patch 1/20] adds support to enable/disable vlan filter with ethtool
[Patch 2/20] disables VFs change rxvlan offload status
[Patch 3/20 - 13/120 fix bugs and refine some codes for packet
statistics, support query with both ifconfig and ethtool.
[Patch 14/20 - 20/20] fix some other bugs.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The statistics of rx/tx packets size greater than 1518
are not detailed. This patch adds more statistics for
different packet size range.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a redundant semicolon, this patch removes it.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pause parameters include source address, transmit gap and pause time.
The default value of the pause source address is zero in the hardware.
Default pause parameters need to be set to the hardware. Also, when
setting new mac address, the pause source address need to be updated.

Fixes: 9dc2145d ("net: hns3: Add support for PFC setting in TM module")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When initializing the MAC, the MTU vlaue need to be set to the hardware
too. Otherwise, the MTU value of software will be different from the MTU
value of hardware.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when changing MTU, The new MTU must need to be set to netdevice.

Fixes: a8e8b7ff ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting MTU, actually what we do is configuring the max frame size
for the hardware. ETH_HLEN、ETH_FCS_LEN and VLAN_HLEN must need to be
considered. And the frame size which is less than the default value
should not be set to the hardware. Because in the hardware, the the max
frame size not only controls the RX packet size, but also controls the
TX packet size. the RX packets whose size are greater than the setting
value will be dropped.

This patch fixes the bug setting a error max frame size to hardware.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit a9c782822166 ("net: hns3: add support for set_pauseparam")
adds set_pauseparam support for ethtool cmd, but forgets to update
fc_mode_last_time when PFC mode is disabled in hclge_cfg_pauseparam().
The wrong fc_mode_last_time will be used to update flow control mode
when lldpad has been running. As a result, when using the ethtool
command "-a", user will get a wrong pause parameter.

This patch adds the fc_mode_last_time update when PFC mode is disabled.

Fixes: a9c782822166 ("net: hns3: add support for set_pauseparam")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The result of tqp statistics query was read with an
error position, fix it according to the user manual.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add packet statistics of netdev for ethtool -S, in
order to show the statistics data for current net
device.

Remove update_stats() calling because it has been
completed in hns3_get_netdev_stats().
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The member "stats_size" of struct hns3_stats is useless,
remove it and fix the macro definition which has uses this
struct.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>