This adds struct device_dma_parameters in struct pci_dev and properly
sets up a pointer in struct device.

The default max_segment_size is set to 64K, same to the block layer's
default value.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Mostly-acked-by: NJeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

IOMMUs merges scatter/gather segments without considering a low level
driver's restrictions. The problem is that IOMMUs can't access to the
limitations because they are in request_queue.

This patchset introduces a new structure, device_dma_parameters,
including dma information. A pointer to device_dma_parameters is added
to struct device. The bus specific structures (like pci_dev) includes
device_dma_parameters. Low level drivers can use dma_set_max_seg_size
to tell IOMMUs about the restrictions.

We can move more dma stuff in struct device (like dma_mask) to struct
device_dma_parameters later (needs some cleanups before that).

This includes patches for all the IOMMUs that could merge sg (x86_64,
ppc, IA64, alpha, sparc64, and parisc) though only the ppc patch was
tested. The patches for other IOMMUs are only compile tested.

This patch:

Add a new structure, device_dma_parameters, including dma information.  A
pointer to device_dma_parameters is added to struct device.

- there are only max_segment_size and segment_boundary_mask there but we'll
  move more dma stuff in struct device (like dma_mask) to struct
  device_dma_parameters later.  segment_boundary_mask is not supported yet.

- new accessors for the dma parameters are added.  So we can easily change
  where to place struct device_dma_parameters in the future.

- dma_get_max_seg_size returns 64K if dma_parms in struct device isn't set
  up properly.  64K is the default max_segment_size in the block layer.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The clock to generate the desired baudrate with the MPSC is first divided
by the Baud Rate Generator (BRG) and then by the MPSC itself.  So, when the
BRG divider is changed, the MPSC divider must also be changed to generate
the correct baudrate.  During MPSC initialization, the BRG divider is
changed but the MPSC divider isn't changed until much later.  This results
in some printk's coming out garbled.  To fix that, set the MPSC divider at
the same time that the BRG divider is changed.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Coding style tweaks and printk levels.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Invalid speeds are forced to 9600. Update the code for this to encode new
style baud rates properly.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some ports seem to be unable to drain their transmitters on shut down.  Such a
problem can occur if the port is programmed for hardware imposed flow control,
characters are in the FIFO but the CTS signal is inactive.

Normally, this isn't a problem because most places where we wait for the
transmitter to drain have a time-out.  However, there is no timeout in the
suspend path.

Give a port 30ms to drain; this is an arbitary value chosen to avoid long
delays if there are many such ports in the system, while giving a reasonable
chance for a single port to drain.  Should a port not drain within this
timeout, issue a warning.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When we boot, serial ports remain in low power mode until they're used either
by userspace or for the kernel console.

However, if you suspend the system, and then resume, all serial ports will be
taken out of low power mode.  This is bad news for embedded devices where this
can mean higher power consumption.

Only bring a serial port out of low power mode if the port is being used as
the kernel console, or is in use by userspace.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow the private_data field to be specified in platform_data for the
standard 8250/16550 UART.  This field is used by DW APB type UARTs and
without this patch it's only possible to set this field when registering
the port by hand.  If private_data is not set then the driver will
potentially oops with a NULL pointer dereference.
Signed-off-by: NWill Newton <will.newton@gmail.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add ADDI-DATA GmbH communication cards to 8250_pci driver.  Supported cards
are:

APCI-7300, APCI-7420, APCI-7500, APCI-7800 APCI-7300-2, APCI-7420-2,
APCI-7500-2 APCI-7300-3, APCI-7420-3, APCI-7500-3, APCI-7800-3

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NKrauth J. <krauth.julien@addi-data.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove dead config symbol.
Signed-off-by: NJiri Olsa <olsajiri@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Dooks <ben@fluff.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

with reverting "x86, serial: convert legacy COM ports to platform devices",
we will have the serial console before the port is probled again.

uart_add_one_port==>uart_configure_port==>set_mcttrl(port, 0) will clear
the DTR setting by uart_set_options().  then I will lose my output from
serial console again.

So try to keep DTR in uart_configure_port()
Signed-off-by: NYinghai Lu <yinghai.lu@sun.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

pci_get_slot does a pci_dev_get, so pci_dev_put needs to be called in an
error case.

An extract of the semantic match used to find the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type find1.T,T1,T2;
identifier find1.E;
statement find1.S;
expression x1,x2,x3;
expression find1.test;
int ret != 0;
@@

  T E;
  ...
(
* E = pci_get_slot(...);
  if (E == NULL) S
|
* if ((E = pci_get_slot(...)) == NULL)
  S
)
  ... when != pci_dev_put(...,(T1)E,...)
      when != if (E != NULL) { ... pci_dev_put(...,(T1)E,...); ...}
      when != x1 = (T1)E
      when != E = x3;
      when any
  if (test) {
    ... when != pci_dev_put(...,(T2)E,...)
        when != if (E != NULL) { ... pci_dev_put(...,(T2)E,...); ...}
        when != x2 = (T2)E
(
*   return;
|
*   return ret;
)
  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

of_iomap calls ioremap, and so should be matched with an iounmap.  At the
two error returns, the result of calling of_iomap is only stored in a local
variable, so these error paths need to call iounmap.  Furthermore, this
function ultimately stores the result of of_iomap in an array that is local
to the file.  These values should be iounmapped at some point.  I have
added a corresponding call to iounmap at the end of the function
m8xx_remove.

The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@

  T E;
  ...
* E = of_iomap(...);
  if (E == NULL) S
  ... when != iounmap(...,(T1)E,...)
      when != if (E != NULL) { ... iounmap(...,(T1)E,...); ...}
      when != x1 = (T1)E
      when != E = x3;
      when any
  if (...) {
    ... when != iounmap(...,(T2)E,...)
        when != if (E != NULL) { ... iounmap(...,(T2)E,...); ...}
        when != x2 = (T2)E
(
*   return;
|
*   return ret;
)
  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update the AT91 CF driver to use the generic GPIO calls instead of the
AT91-specific ones; and request exclusive use of those signals.

Minor tweaks to cleanup code paths: always in reverse order of how the
resources were allocated, with remove() matching the fault paths of
probe().
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/pcnet_cs.c
drivers/net/pcmcia/pcnet_cs.c:523:15: warning: symbol 'hw_info' shadows an earlier one
drivers/net/pcmcia/pcnet_cs.c:148:18: originally declared here
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/fmvj18x_cs.c
drivers/net/pcmcia/fmvj18x_cs.c:1205:6: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/fmvj18x_cs.c:1179:9: originally declared here
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use 'max(x,y)' instead of 'x < y ? y : x'.
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/axnet_cs.c
drivers/net/pcmcia/axnet_cs.c:994:5: warning: symbol 'ax_close' was not declared. Should it be static?
drivers/net/pcmcia/axnet_cs.c:1017:6: warning: symbol 'ei_tx_timeout' was not declared. Should it be static?
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   drivers/net/pcmcia/3c574_cs.c
drivers/net/pcmcia/3c574_cs.c:695:7: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/3c574_cs.c:636:6: originally declared here
Signed-off-by: NRichard Knutson <ricknu-0@student.ltu.se>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Print the invalid CIS filename in the invalid filename message.
- Use sizeof() instead of hard-coded constant for buffer size.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This stops the pcmcia core from using dev->power.power_state; that field is
deprecated (overdue for removal) and the only reason to update it was to make
the /sys/devices/.../power/state files (now removed) work better.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove kio_addr_t, and replace it with unsigned int.  No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert the io_req_t members to unsigned int, to allow use on machines with
more than 16 bits worth of IO ports (i.e.  secondary busses on ppc64, etc).

There was only a couple of places in drivers where a change was needed.  I
left printk formats alone (there are lots of %04x-style formats in there),
mostly to not change the format on the platforms that only have 16-bit io
addresses, but also because the padding doesn't really add all that much value
most of the time.

I found only one sprintf of an address, and upsized the string accordingly (I
doubt anyone will have anywhere near INT_MAX as irq value, but at least
there's room for it now).
Signed-off-by: NOlof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

remove dead config symbols from M32R code
Signed-off-by: NJiri Olsa <olsajiri@gmail.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

CC [M]  sound/ppc/awacs.o
In file included from sound/ppc/awacs.c:24:
include/asm/nvram.h:62: error: field 'partition' has incomplete type
Reported-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

FATAL: drivers/bluetooth/btsdio: sizeof(struct sdio_device_id)=12 is not a modulo of the size of section __mod_sdio_device_table=30.
Fix definition of struct sdio_device_id in mod_devicetable.h

m68k has 16bit alignment for unsigned long.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Pierre Ossman <drzeus@drzeus.cx>
CC: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the broken status to CONFIG_TIMERFD.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Wires up the new timerfd API to the x86 family.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the new timerfd API as it is implemented by the following patch:

int timerfd_create(int clockid, int flags);
int timerfd_settime(int ufd, int flags,
		    const struct itimerspec *utmr,
		    struct itimerspec *otmr);
int timerfd_gettime(int ufd, struct itimerspec *otmr);

The timerfd_create() API creates an un-programmed timerfd fd.  The "clockid"
parameter can be either CLOCK_MONOTONIC or CLOCK_REALTIME.

The timerfd_settime() API give new settings by the timerfd fd, by optionally
retrieving the previous expiration time (in case the "otmr" parameter is not
NULL).

The time value specified in "utmr" is absolute, if the TFD_TIMER_ABSTIME bit
is set in the "flags" parameter.  Otherwise it's a relative time.

The timerfd_gettime() API returns the next expiration time of the timer, or
{0, 0} if the timerfd has not been set yet.

Like the previous timerfd API implementation, read(2) and poll(2) are
supported (with the same interface).  Here's a simple test program I used to
exercise the new timerfd APIs:

http://www.xmailserver.org/timerfd-test2.c

[akpm@linux-foundation.org: coding-style cleanups]
[akpm@linux-foundation.org: fix ia64 build]
[akpm@linux-foundation.org: fix m68k build]
[akpm@linux-foundation.org: fix mips build]
[akpm@linux-foundation.org: fix alpha, arm, blackfin, cris, m68k, s390, sparc and sparc64 builds]
[heiko.carstens@de.ibm.com: fix s390]
[akpm@linux-foundation.org: fix powerpc build]
[akpm@linux-foundation.org: fix sparc64 more]
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I think that advancing the timer against the timer's current "now" can be a
pretty common usage, so, w/out exposing hrtimer's internals, we add a new
hrtimer_forward_now() function.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As Roland pointed out, we have the very old problem with exec.  de_thread()
sets SIGNAL_GROUP_EXIT, kills other threads, changes ->group_leader and then
clears signal->flags.  All signals (even fatal ones) sent in this window
(which is not too small) will be lost.

With this patch exec doesn't abuse SIGNAL_GROUP_EXIT.  signal_group_exit(),
the new helper, should be used to detect exit_group() or exec() in progress.
It can have more users, but this patch does only strictly necessary changes.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robin Holt <holt@sgi.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Every time we set SIGNAL_GROUP_EXIT or clear SIGNAL_STOP_DEQUEUED we also
reset ->group_stop_count.

This means that the SIGNAL_GROUP_EXIT check in handle_group_stop() is not
needed, and do_signal_stop() should check SIGNAL_STOP_DEQUEUED only when
->group_stop_count == 0. With these changes handle_group_stop() becomes the
subset of do_signal_stop(), we can kill it and use do_signal_stop() instead.

Also, a preparation for the next patch.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robin Holt <holt@sgi.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When __group_complete_signal() sees sig_kernel_coredump() signal, it starts
the group stop, but sets ->group_exit_task = t in a hope that "t" will
actually dequeue this signal and invoke do_coredump().  However, by the
time "t" enters get_signal_to_deliver() it is possible that the signal was
blocked/ignored or we have another pending !SIG_KERNEL_COREDUMP_MASK signal
which will be dequeued first.  This means the task could be stopped but not
killed.

Remove this code from __group_complete_signal().  Note also this patch
removes the bogus signal_wake_up(t, 1).  This thread can't be
STOPPED/TRACED, note the corresponding check in wants_signal().
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robin Holt <holt@sgi.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ulrich says that we never used this clone flags and that nothing should be
using it.

As we're down to only a single bit left in clone's flags argument, let's add a
warning to check that no userspace is actually using it.  Hopefully we will
be able to recycle it.

Roland said:

  CLONE_STOPPED was previously used by some NTPL versions when under
  thread_db (i.e.  only when being actively debugged by gdb), but not for a
  long time now, and it never worked reliably when it was used.  Removing it
  seems fine to me.

[akpm@linux-foundation.org: it looks like CLONE_DETACHED is being used]
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It was dumb to make get_task_comm() return void.  Change it to return a
pointer to the resulting output for caller convenience.

Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On Sat, 2008-01-05 at 13:35 -0800, Davide Libenzi wrote:

> I remember I talked with Arjan about this time ago. Basically, since 1)
> you can drop an epoll fd inside another epoll fd 2) callback-based wakeups
> are used, you can see a wake_up() from inside another wake_up(), but they
> will never refer to the same lock instance.
> Think about:
>
> 	dfd = socket(...);
> 	efd1 = epoll_create();
> 	efd2 = epoll_create();
> 	epoll_ctl(efd1, EPOLL_CTL_ADD, dfd, ...);
> 	epoll_ctl(efd2, EPOLL_CTL_ADD, efd1, ...);
>
> When a packet arrives to the device underneath "dfd", the net code will
> issue a wake_up() on its poll wake list. Epoll (efd1) has installed a
> callback wakeup entry on that queue, and the wake_up() performed by the
> "dfd" net code will end up in ep_poll_callback(). At this point epoll
> (efd1) notices that it may have some event ready, so it needs to wake up
> the waiters on its poll wait list (efd2). So it calls ep_poll_safewake()
> that ends up in another wake_up(), after having checked about the
> recursion constraints. That are, no more than EP_MAX_POLLWAKE_NESTS, to
> avoid stack blasting. Never hit the same queue, to avoid loops like:
>
> 	epoll_ctl(efd2, EPOLL_CTL_ADD, efd1, ...);
> 	epoll_ctl(efd3, EPOLL_CTL_ADD, efd2, ...);
> 	epoll_ctl(efd4, EPOLL_CTL_ADD, efd3, ...);
> 	epoll_ctl(efd1, EPOLL_CTL_ADD, efd4, ...);
>
> The code "if (tncur->wq == wq || ..." prevents re-entering the same
> queue/lock.

Since the epoll code is very careful to not nest same instance locks
allow the recursion.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k:

drivers/net/wireless/b43/main.c:251: error: implicit declaration of function 'mmiowb'

Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix ->vm_file accounting, mmap_region() may do do_munmap().
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

arch/x86/kvm/x86.c: In function 'emulator_cmpxchg_emulated':
arch/x86/kvm/x86.c:1746: warning: passing argument 2 of 'vcpu->arch.mmu.gva_to_gpa' makes integer from pointer without a cast
arch/x86/kvm/x86.c:1746: warning: 'addr' is used uninitialized in this function

Is true.  Local variable `addr' shadows incoming arg `addr'.  Avi is on
vacation for a while, so...

Cc: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
  [ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
  [ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
  [ARM] 4820/1: RealView: Select the timer IRQ at run-time
  [ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
  [ARM] 4818/1: RealView: Add core-tile detection
  [ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
  [ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
  [ARM] 4815/1: RealView: Add clockevents suport for the local timers
  [ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
  [ARM] 4813/1: Add SMP helper functions for clockevents support
  [ARM] 4812/1: RealView: clockevents support for the RealView platforms
  [ARM] 4811/1: RealView: clocksource support for the RealView platforms
  [ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
  [ARM] 4798/1: pcm027: fix missing header file
  [ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
  [ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
  [ARM] pxa: introduce sysdev for pxa3xx static memory controller
  [ARM] pxa: add preliminary suspend/resume code for pxa3xx
  [ARM] pxa: introduce sysdev for GPIO register saving/restoring
  [ARM] pxa: introduce sysdev for IRQ register saving/restoring
  ...