- 20 6月, 2006 40 次提交
-
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
It is done by the generic IRQ layer now. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This is the long overdue conversion of sparc64 over to the generic IRQ layer. The kernel image is slightly larger, but the BSS is ~60K smaller due to the reduced size of struct ino_bucket. A lot of IRQ implementation details, including ino_bucket, were moved out of asm-sparc64/irq.h and are now private to arch/sparc64/kernel/irq.c, and most of the code in irq.c totally disappeared. One thing that's different at the moment is IRQ distribution, we do it at enable_irq() time. If the cpu mask is ALL then we round-robin using a global rotating cpu counter, else we pick the first cpu in the mask to support single cpu targetting. This is similar to what powerpc's XICS IRQ support code does. This works fine on my UP SB1000, and the SMP build goes fine and runs on that machine, but lots of testing on different setups is needed. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Inspired by PowerPC XICS interrupt support code. All IRQs are virtualized in order to keep NR_IRQS from needing to be too large. Interrupts on sparc64 are arbitrary 11-bit values, but we don't need to define NR_IRQS to 2048 if we virtualize the IRQs. As PCI and SBUS controller drivers build device IRQs, we divy out virtual IRQ numbers incrementally starting at 1. Zero is a special virtual IRQ used for the timer interrupt. So device drivers all see virtual IRQs, and all the normal interfaces such as request_irq(), enable_irq(), etc. translate that into a real IRQ number in order to configure the IRQ. At this point knowledge of the struct ino_bucket is almost entirely contained within arch/sparc64/kernel/irq.c There are a few small bits in the PCI controller drivers that need to be swept away before we can remove ino_bucket's definition out of asm-sparc64/irq.h and privately into kernel/irq.c Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
And reuse that struct member for virt_irq, which will be used in future changesets for the implementation of mapping between real and virtual IRQ numbers. This nicely kills off a ton of SBUS and PCI controller PIL assignment code which is no longer necessary. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This ugly hack was long overdue to die. It was a way to print out Sparc interrupts in a more freindly format, since IRQ numbers were arbitrary opaque 32-bit integers which vectored into PIL levels. These 32-bit integers were not necessarily in the 0-->NR_IRQS range, but the PILs they vectored to were. The idea now is that we will increase NR_IRQS a little bit and use a virtual<-->real IRQ number mapping scheme similar to PowerPC. That makes this IRQ printing hack irrelevant, and furthermore only a handful of drivers actually used __irq_itoa() making it even less useful. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Only pil0_dummy_bucket had a pil of zero and we just killed that off, so we can delete all special case code that used bp->pil==0 as a way to identify a dummy bucket. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
This is the first in a series of cleanups that will hopefully allow a seamless attempt at using the generic IRQ handling infrastructure in the Linux kernel. Define PIL_DEVICE_IRQ and vector all device interrupts through there. Get rid of the ugly pil0_dummy_{bucket,desc}, instead vector the timer interrupt directly to a specific handler since the timer interrupt is the only event that will be signaled on PIL 14. The irq_worklist is now in the per-cpu trap_block[]. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bob Breuer 提交于
Fix the calculation of the end address when flushing iotlb entries to ram. This bug has been a cause of esp dma errors, and it affects HyperSPARC systems much worse than SuperSPARC systems. Signed-off-by: NBob Breuer <breuerr@mc.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bob Breuer 提交于
Fix the smp related section mismatch warnings by marking the smp init functions as cpuinit. Signed-off-by: NBob Breuer <breuerr@mc.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bob Breuer 提交于
Fix a link failure by adding the missing can_lock macros for the rw locks. Signed-off-by: NBob Breuer <breuerr@mc.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bob Breuer 提交于
Setup cpu_possible_map so the secondary cpus will get started. Signed-off-by: NBob Breuer <breuerr@mc.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bob Breuer 提交于
Fix a crash in SMP mode by adding the missing topology_init. Also makes /proc/cpuinfo backwards compatible with 2.4. Signed-off-by: NBob Breuer <breuerr@mc.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://ftp.linux-mips.org/pub/scm/upstream-linus由 Linus Torvalds 提交于
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits) [MIPS] Make timer interrupt frequency configurable from kconfig. [MIPS] Correct HAL2 Kconfig description [MIPS] Fix R4K cache macro names [MIPS] Add Missing R4K Cache Macros to IP27 & IP32 [MIPS] Support for the RM9000-based Basler eXcite smart camera platform. [MIPS] Support for the R5500-based NEC EMMA2RH Mark-eins board [MIPS] Support SNI RM200C SNI in big endian mode and R5000 processors. [MIPS] SN: include asm/sn/types.h for nasid_t. [MIPS] Random fixes for sb1250 [MIPS] Fix bcm1480 compile [MIPS] Remove support for NEC DDB5476. [MIPS] Remove support for NEC DDB5074. [MIPS] Cleanup memory managment initialization. [MIPS] SN: Declare bridge_pci_ops. [MIPS] Remove unused function alloc_pci_controller. [MIPS] IP27: Extract pci_ops into separate file. [MIPS] IP27: Use symbolic constants instead of magic numbers. [MIPS] vr41xx: remove unnecessay items from vr41xx/Kconfig. [MIPS] IP27: Cleanup N/M mode configuration. [MIPS] IP27: Throw away old unused hacks. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (46 commits) IB/uverbs: Don't serialize with ib_uverbs_idr_mutex IB/mthca: Make all device methods truly reentrant IB/mthca: Fix memory leak on modify_qp error paths IB/uverbs: Factor out common idr code IB/uverbs: Don't decrement usecnt on error paths IB/uverbs: Release lock on error path IB/cm: Use address handle helpers IB/sa: Add ib_init_ah_from_path() IB: Add ib_init_ah_from_wc() IB/ucm: Get rid of duplicate P_Key parameter IB/srp: Factor out common request reset code IB/srp: Support SRP rev. 10 targets [SCSI] srp.h: Add I/O Class values IB/fmr: Use device's max_map_map_per_fmr attribute in FMR pool. IB/mthca: Fill in max_map_per_fmr device attribute IB/ipath: Add client reregister event generation IB/mthca: Add client reregister event generation IB: Move struct port_info from ipath to <rdma/ib_smi.h> IPoIB: Handle client reregister events IB: Add client reregister event type ...
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (109 commits) [ETHTOOL]: Fix UFO typo [SCTP]: Fix persistent slowdown in sctp when a gap ack consumes rx buffer. [SCTP]: Send only 1 window update SACK per message. [SCTP]: Don't do CRC32C checksum over loopback. [SCTP] Reset rtt_in_progress for the chunk when processing its sack. [SCTP]: Reject sctp packets with broadcast addresses. [SCTP]: Limit association max_retrans setting in setsockopt. [PFKEYV2]: Fix inconsistent typing in struct sadb_x_kmprivate. [IPV6]: Sum real space for RTAs. [IRDA]: Use put_unaligned() in irlmp_do_discovery(). [BRIDGE]: Add support for NETIF_F_HW_CSUM devices [NET]: Add NETIF_F_GEN_CSUM and NETIF_F_ALL_CSUM [TG3]: Convert to non-LLTX [TG3]: Remove unnecessary tx_lock [TCP]: Add tcp_slow_start_after_idle sysctl. [BNX2]: Update version and reldate [BNX2]: Use CPU native page size [BNX2]: Use compressed firmware [BNX2]: Add firmware decompression [BNX2]: Allow WoL settings on new 5708 chips ... Manual fixup for conflict in drivers/net/tulip/winbond-840.c
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/intelfb-2.6由 Linus Torvalds 提交于
* 'i915fb' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/intelfb-2.6: (25 commits) intelfb: fixup clock calculation debugging. Removed hard coded EDID buffer size. intelfb: use regular modedb table instead of VESA intelfb: use firmware EDID for mode database Revert "intelfb driver -- use the regular modedb table instead of the VESA" intelfb: int option fix sync modesetting code with X.org intelfb: align with changes from my X driver. intelfb driver -- use the regular modedb table instead of the VESA Adds support for 256MB aperture on 945 chipsets to the intelfb driver intelfb -- uses stride alignment of 64 on the 9xx chipsets. intelfb: some cleanups for intelfbhw intelfb: fixup pitch calculation like X does intelfb: fixup p calculation This patch makes a needlessly global struct static. intelfb: add i945GM support intelfb: fixup whitespace.. intelfb: add hw cursor support for i9xx intelfb: make i915 modeset intelfb: add support for i945G ...
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart: [AGPGART] alpha-agp warning fix [AGPGART] uninorth-agp warning fixes [AGPGART] Remove pointless initialisation in intel-agp [AGPGART] Remove pointless code from agp_generic_create_gatt_table()
-
由 Linus Torvalds 提交于
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq: [CPUFREQ] sets nforce2 minimum PLL divider to 2. [CPUFREQ] Make powernow-k7 work on SMP kernels. [CPUFREQ] cpufreq core {d,}printk adjustments [CPUFREQ] dprintk adjustments to cpufreq-speedstep-centrino [CPUFREQ] dprintk adjustments to cpufreq-nforce2 [CPUFREQ] Prepare powernow-k8 for future CPUs. [CPUFREQ] Make acpi-cpufreq 'sticky'. [CPUFREQ] Remove strange No-op from longrun.c [CPUFREQ] Remove more freq_table reinitialisations. [CPUFREQ] Fix another redundant initialisation in freq_table [CPUFREQ] Remove duplicate assignment in freq_table [CPUFREQ] CodingStyle nits in cpufreq_stats.c [CPUFREQ] Remove duplicate assignment from cpufreq-nforce2 [CPUFREQ] Remove pointless reinitialisations in acpi-cpufreq [CPUFREQ] Remove pointless reinitialisation from powernow-k8 [CPUFREQ] Remove redundant initialisation from longhaul. [CPUFREQ] Clean up longhaul's speed pretty-printer [CPUFREQ] Disambiguate loop indexes in powernow-k7 [CPUFREQ] Typo in powernow-k8
-
由 Linus Torvalds 提交于
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (166 commits) [PATCH] net: au1000_eth: PHY framework conversion [PATCH] 3c5zz ethernet: fix section warnings [PATCH] smc ethernet: fix section mismatch warnings [PATCH] hp ethernet: fix section mismatches [PATCH] Section mismatch in drivers/net/ne.o during modpost [PATCH] e1000: prevent statistics from getting garbled during reset [PATCH] smc911x Kconfig fix [PATCH] forcedeth: new device ids [PATCH] forcedeth config: version [PATCH] forcedeth config: module parameters [PATCH] forcedeth config: diagnostics [PATCH] forcedeth config: move functions [PATCH] forcedeth config: statistics [PATCH] forcedeth config: csum [PATCH] forcedeth config: wol [PATCH] forcedeth config: phy [PATCH] forcedeth config: flow control [PATCH] forcedeth config: ring sizes [PATCH] forcedeth config: tso cleanup [DOC] Update bonding documentation with sysfs info ...
-
由 Linus Torvalds 提交于
Trying to suspend/resume with console messages flying all around is doomed to failure, when the devices that the messages are trying to go to are being shut down. Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Linus Torvalds 提交于
According to the ACPI spec, it should be enabled on return from suspend, but bugs happen. Apparently especially on the Apple Intel Macs. Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Linus Torvalds 提交于
Doing a full ata_busy_sleep() seems to get suspend and resume working fine on the Apple Mac Mini, at least. Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Atsushi Nemoto 提交于
Make HZ configurable. DECSTATION can select 128/256/1024 HZ, JAZZ can only select 100 HZ, others can select 100/128/250/256/1000/1024 HZ if not explicitly specified). Also remove all mach-xxx/param.h files and update all defconfigs according to current HZ value. Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Kumba 提交于
The current HAL2 Kconfig description indicates it is only used on SGI Indy systems, however all members of the Indigo2 Family have this sound card as well. Plus a minor grammatical fix is included. Signed-off-by: NJoshua Kinard <kumba@gentoo.org> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Kumba 提交于
Several machines have the R4K cache macro name spelled incorrectly. Namely, they have cpu_has_4kcache defined instead of cpu_has_4k_cache. Signed-off-by: NJoshua Kinard <kumba@gentoo.org> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Kumba 提交于
Keeping in accordance with other machines, IP27 and IP32 lack a few macros. IP27 lacks cpu_has_4kex & cpu_has_4k_cache macros while IP32 lacks just the cpu_has_4k_cache macro. Signed-off-by: NJoshua Kinard <kumba@gentoo.org> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 dmitry pervushin 提交于
Signed-off-by: Ndmitry pervushin <dpervushin@ru.mvista.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Thomas Bogendoerfer 提交于
Added support for RM200C machines with big endian firmware Added support for RM200-C40 (R5000 support) Signed-off-by: NFlorian Lohoff <flo@rfc822.org> Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Thiemo Seufer 提交于
Random improvements for sb1250: Silence compiler warnings, a bugfix for the profiling code, and a comment typo. Signed-off-by: NThiemo Seufer <ths@networkno.de> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Thiemo Seufer 提交于
Fix compilation for bcm1480, a hpt is only available on sb1250/bcm112x. Signed-off-by: NThiemo Seufer <ths@networkno.de> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
As warned several times before. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
As warned several times before. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Historically plat_mem_setup did the entire platform initialization. This was rather impractical because it meant plat_mem_setup had to get away without any kind of memory allocator. To keep old code from breaking plat_setup was just renamed to plat_setup and a second platform initialization hook for anything else was introduced. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-