module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.

(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).

Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.

2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
   IB or Ethernet.
   The driver will use this hint in case the user didn't specify explicitly the link layer
   type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
   and default the port to link sensing
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Added module parameters sr_iov and probe_vf for controlling enablement of
   SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
   SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
   ports configured as desired.
   In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
   for the case where the FW supports both port types (ETH and IB), the
   port_type_array parameter is used.
   By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
   to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
   mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
   modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
   VFs obtain their startup information from the PF (master) device via the
   comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
   aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership:  Currently, only one PF is supported by the driver.
   If the HCA is burned with FW which enables more than one PF, only one
   of the PFs is allowed to run.  The first one up grabs a FW ownership
   semaphone -- all other PFs will find that semaphore taken, and the
   driver will not allow them to run.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NLiran Liss <liranl@mellanox.co.il>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the previous implementation mtts are managed by:
1. order     - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order     - log(mtts) rather than segments
2. offset    - mtt index in mtt table

Note: The actual mtt allocation is made in segments but it is
      transparent to callers.

Rational: The mtt resource holders are not interested on how the allocation
          of mtt is done, but rather on how they will use it.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper.  This function is used by VFs when
   they start up to receive configuration information from the PF, such
   as resource quotas for this VF, which ports should be used (currently
   two), what protocol is running on the port (currently Ethernet ONLY,
   or port not active).

2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
   by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
   required here (the VF's MAC address must be substituted for the PFs
   MAC address returned by the FW). We changed the invocation
   in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.

3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
   For now, we need only the multicast table member entry size
   (log2_mc_table_entry_sz, in the ConnectX PRM).  No wrapper is needed
   here, because the data may be passed as is to the VF without modification).

   In this command, we have added a GLOBAL_CAPS field for passing required
   configuration information from FW to a VF (this field is to allow safely
                   adding new SRIOV capabilities which require support in VF drivers, too).
   Bits will set here by FW in response to PF-driver configuration commands which
   will activate as yet undefined new SRIOV features. The VF will test to see that
   all required capabilities indicated by this field are supported (i.e., if a bit
   is set and the VF driver does not recognize that bit, it must abort
   its initialization).  Currently, no bits are set.

4. Added a CLOSE_PORT wrapper.  The PF context needs to keep track of how many VF contexts
   have the port open.  The PF context will not actually issue the FW close port command
   until the last port user issues a CLOSE_PORT request.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).

This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.

Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device.h header was including module.h, making it present for
most of these drivers.  But we want to clean that up.  Call out the
include of module.h in the modular network drivers.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Canceling FCS removal where FW allows for better alignment
of incoming data.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.

CC: Roland Dreier <roland@kernel.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ConnectX devices support a set of flow counters that can be attached
to a set containing one or more QPs.  Each such counter tracks receive
and transmit packets and bytes of these QPs.  This patch queries the
device to check support for counters, handles initialization of the
HCA to enable counters, and initializes a bitmap allocator to control
counter allocations.  Derived from patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Query another dword containing up to 32 extended device capabilities
and merge it into struct mlx4_caps.flags.  Update the code that
handles the current extended device capabilities (e.g UDP RSS, WoL,
vep steering, etc) to use the extended device cap flags field instead
of a field per extended capability.  Initial patch done by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The latest firmware adds a second dword containing more device flags,
so extend the device capabilities flags field from 32 to 64 bits.
Derived from patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The mlx4_en module now uses the new steering mechanism.
The RX packets are now steered through the MCG table instead
of Mac table for unicast, and default entry for multicast.
The feature is enabled through INIT_HCA
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: NIgor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel warning message added in commit 58d74bb1 ("mlx4_core:
Workaround firmware bug in query dev cap") about mlx4 reporting the
wrong number of "blue flame registers" doesn't really help anyone, since
the firmware bug is known and fixed and the bug is pretty much harmless
to users.  So just get rid of the warning.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX firmware is supposed to report the number blue flame
registers per page as log2 of the value.  However, due to a firmware
bug, it reports actual number.  This patch works around this by
checking if the number of registers calculated fits within a page.  If
it does not, we use 8 registers per page.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add fields to hardware data structures and add new constants required for IBoE
support.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Adding capability for RSS for UDP traffic, hashing is done based on
IP addresses and UDP port number.
The support depends on HW/FW capabilities.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The report now based on query from FW, giving the correct tranciever type
and link speed.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
   on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Value returned by firmware is the actual value, not a log.
Signed-off-by: NLiran Liss <liranl@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary.  This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size.  The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length.  Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX can work more efficiently if the CPU cache line size is passed
to it with the INIT_HCA firmware command.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Multi-protocol adapters support different port types.  Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it.  Port type
is configured through a sysfs interface.  When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get maximum ethernet MTU and default MAC address from the firmware
QUERY_DEV_CAP command.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For ethernet support, we need to reserve QPs for the ethernet and
fibre channel driver.  The QPs are reserved at the end of the QP
table.  (This way we assure that they are aligned to their size)

We need to consider these reserved ranges in bitmap creation, so we
extend the mlx4 bitmap utility functions to allow reserved ranges at
both the bottom and the top of the range.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for the following operations to mlx4 when device firmware
supports them:

 - Send with invalidate and local invalidate send queue work requests;
 - Allocate/free fast register MRs;
 - Allocate/free fast register MR page lists;
 - Fast register MR send queue work requests;
 - Local DMA L_Key.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a module parameter "enable_qos" to mlx4_core.  If this param is
set, enable support for QoS in the INIT_HCA command.  By default, the
parameter is set to 0 (disabled).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There was a bug in some versions of the mlx4 driver in
mlx4_alloc_fmr(), which hardcoded the minimum acceptable page_shift to
be 12.  However, new ConnectX firmware can support a minimum
page_shift of 9 (log_pg_sz of 9 returned by QUERY_DEV_LIM) -- so with
old drivers, ib_fmr_alloc() would fail for ULPs using the device
minimum when creating FMRs.

To preserve firmware compatibility with released mlx4 drivers, the
firmware will continue to return 12 as before for log_page_sz in
QUERY_DEV_CAP for these drivers.  However, to enable new drivers to
take advantage of the available smaller page size, the mlx4 driver now
first sets the log_pg_sz to the device minimum by setting a
log_page_sz value to 0 via the MOD_STAT_CFG command and then reading
the real minimum via QUERY_DEV_CAP.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add TSO support to the mlx4_ib driver.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages.  This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does.  It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NAli Ayub <ali@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.

Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

log_max_eqs is a 4-bit field, not a 3-bit field in the response to the
QUERY_DEV_CAP FW command, so we should mask with 0xf instead of 0x7
when reading it.

Found by Yossi Leybovitch of Mellanox.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The current INIT_HCA firmware command timeout is sufficient for the
default number of resources (QPs, CQs, etc) being allocated, but if
the HCA profile is modified to increase the amount of resources, then
a spurious timeout is detected and HCA initialization fails.

Increase the timeout for the INIT_HCA command to 10 seconds, which
also brings it into line with all the other command timeouts.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The SRC ("scalable RC") transport has been renamed to XRC ("extended 
RC"), to avoid having an abbreviation that is so easily confused with an 
abbreviation for "source."  Update the HCA capability decoding output to 
use the new name.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set.  Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>