Bloom filter is a bit vector which allows the HW a fast lookup on a
small size bit vector, that may reduce the number of lookups on the
A-TCAM memory. PEABFE register allows setting values to the bits of
the bit vector mentioned above.
Add the register to be later used in A-TCAM optimizations.
Signed-off-by: NNir Dotan <nird@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
rtnl fdb get

This series adds support for rtnl fdb get similar to
route get.

v2: add nda_policy, fixes to exact msgs, strict nlmsg parsing

v3: remove unnecessary attribute length checks + simplify code
as pointed out by david
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tests the below three cases of bridge fdb get:
[bridge, mac, vlan]
[bridge_port, mac, vlan, flags=[NTF_MASTER]]
[vxlandev, mac, flags=NTF_SELF]

depends on iproute2 support for bridge fdb get.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements ndo_fdb_get for a vxlan device.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for fdb get similar to
route get. arguments can be any of the following (similar to fdb add/del/dump):
[bridge, mac, vlan] or
[bridge_port, mac, vlan, flags=[NTF_MASTER]] or
[dev, mac, [vni|vlan], flags=[NTF_SELF]]
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marek Vasut says:

====================
net: dsa: ksz: Clean up the tag code in prep for more switches

Clean up the KSZ DSA tag code in preparation for adding more switches.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: NTristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: NTristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW team asks to be able to not support RED even if NIC is capable
of buffering for testing and experimentation.  Add an opt-out flag.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit ec49d83f.

Cause build failures when DCCP is modular.

ERROR: "inet_hashinfo2_init" [net/dccp/dccp.ko] undefined!
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to routes and rules, add protocol attribute to neighbor entries
for easier tracking of how each was created.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds coverage of DCCP to reuseport_addr_any selftest.
Signed-off-by: NPeter Oskolkov <posk@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d9fbc7f6 "net: tcp: prefer listeners bound to an address"
removes port-only listener lookups. This caused segfaults in DCCP
lookups because DCCP did not initialize the (addr,port) hashtable.

This patch adds said initialization.

The only non-trivial issue here is the size of the new hashtable.
It seemed reasonable to make it match the size of the port-only
hashtable (= INET_LHTABLE_SIZE) that was used previously. Other
parameters to inet_hashinfo2_init() match those used in TCP.

Tested: syzcaller issues fixed; the second patch in the patchset
        tests that DCCP lookups work correctly.

Fixes: d9fbc7f6 "net: tcp: prefer listeners bound to an address"
Reported-by: Nsyzcaller <syzkaller@googlegroups.com>
Signed-off-by: NPeter Oskolkov <posk@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Protocol Field Compression (PFC) is enabled, the "Protocol" field
in PPP packet will be received without leading 0x00. See section 6.5 in
RFC 1661 for details. So let's decompress protocol field if needed, the
same way it's done in drivers/net/ppp/pptp.c.

In case when "nopcomp" pppd option is not enabled, PFC (pcomp) can be
negotiated during LCP handshake, and L2TP driver in kernel will receive
PPP packets with compressed Protocol field, which in turn leads to next
error:

    Protocol Rejected (unsupported protocol 0x2145)

because instead of Protocol=0x0021 in PPP packet there will be
Protocol=0x21. This patch unwraps it back to 0x0021, which fixes the
issue.

Sending the compressed Protocol field will be implemented in subsequent
patch, this one is self-sufficient.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5e-updates-2018-12-14 (VF Lag)

From Aviv Heller,

Subsequent patches introduce VF LAG, which provdies load-balancing and
high-availability capabilities for VFs associated with different
physical ports of the same Connect-X card.

This series consists of the following:
 - mlx5 devcom, driver infrastructure that facilitates operations that involve
   both core devices (physical functions) of the same card, to synchronize and
   communicate between two driver instances of the same card.
 - Infrastructure for TC rule duplication.
 - Changes to LAG logic to enable its use when SR-IOV is enabled
 - PFs in switchdev mode is the only mode currently supported.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
net: mitigate retpoline overhead

The spectre v2 counter-measures, aka retpolines, are a source of measurable
overhead[1]. We can partially address that when the function pointer refers to
a builtin symbol resorting to a list of tests vs well-known builtin function and
direct calls.

Experimental results show that replacing a single indirect call via
retpoline with several branches and a direct call gives performance gains
even when multiple branches are added - 5 or more, as reported in [2].

This may lead to some uglification around the indirect calls. In netconf 2018
Eric Dumazet described a technique to hide the most relevant part of the needed
boilerplate with some macro help.

This series is a [re-]implementation of such idea, exposing the introduced
helpers in a new header file. They are later leveraged to avoid the indirect
call overhead in the GRO path, when possible.

Overall this gives > 10% performance improvement for UDP GRO benchmark and
smaller but measurable for TCP syn flood.

The added infra can be used in follow-up patches to cope with retpoline overhead
in other points of the networking stack (e.g. at the qdisc layer) and possibly
even in other subsystems.

v2  -> v3:
 - fix build error with CONFIG_IPV6=m

v1  -> v2:
 - list explicitly the builtin function names in INDIRECT_CALL_*(),
   as suggested by Ed Cree
 - expand the recipients list

rfc -> v1:
 - use branch prediction hints, as suggested by Eric

[1] http://vger.kernel.org/netconf2018_files/PaoloAbeni_netconf2018.pdf
[2] https://linuxplumbersconf.org/event/2/contributions/99/attachments/98/117/lpc18_paper_af_xdp_perf-v2.pdf
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids another indirect call for UDP GRO. Again, the test
for the IPv6 variant is performed first.

v1 -> v2:
 - adapted to INDIRECT_CALL_ changes
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids an indirect call in the receive path for TCP and UDP
packets. TCP takes precedence on UDP, so that we have a single
additional conditional in the common case.

When IPV6 is build as module, all gro symbols except UDPv6 are
builtin, while the latter belong to the ipv6 module, so we
need some special care.

v1 -> v2:
 - adapted to INDIRECT_CALL_ changes
v2 -> v3:
 - fix build issue with CONFIG_IPV6=m
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids an indirect calls for L3 GRO receive path, both
for ipv4 and ipv6, if the latter is not compiled as a module.

Note that when IPv6 is compiled as builtin, it will be checked first,
so we have a single additional compare for the more common path.

v1 -> v2:
 - adapted to INDIRECT_CALL_ changes
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This header define a bunch of helpers that allow avoiding the
retpoline overhead when calling builtin functions via function pointers.
It boils down to explicitly comparing the function pointers to
known builtin functions and eventually invoke directly the latter.

The macros defined here implement the boilerplate for the above schema
and will be used by the next patches.

rfc -> v1:
 - use branch prediction hint, as suggested by Eric
v1  -> v2:
 - list explicitly the builtin function names in INDIRECT_CALL_*(),
   as suggested by Ed Cree
Suggested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the driver issues 2 mmio reads to figure out the number of
transmitted packets and clean them. We can get rid of the expensive
reads since BIT 31 of the Tx descriptor can be used for that.
We can also remove the budget counting of Tx completions since all of
the descriptors are not deliberately processed.

Performance numbers using pktgen are:
size  pre-patch(pps)  post-patch(pps)
64       362483           427916
128      358315           411686
256      352725           389683
512      215675           216464
1024     113812           114442
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Running pktgen with packets sizes > 512b ends up in the interface Txq
getting stuck.
"netsec 522d0000.ethernet eth0: netsec_netdev_start_xmit: TxQFull!"
appears on dmesg but the interface never recovers. It requires an
ifconfig down/up to make the interface usable again.

The reason that triggers this, is a race condition between
.ndo_start_xmit and the napi completion. The available budget is
calculated first and indicates the queue is full. Due to a costly
netif_err() the queue is not stopped in time while the napi completion
runs, clears the irq and frees up descriptors, thus the queue never wakes
up again.

Fix this by moving the print after stopping the queue, make the print
ratelimited, add barriers and check for cleaned descriptors..
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move arp_queue_len_bytes ahead of arp_queue to remove two 4-byte holes.
Ensure ha element is always 8-byte aligned.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Except for returning, the var leaf is not
used in the qdisc_leaf(). For simplicity, remove it.
Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent commit allows sockets bound to a VRF to receive ipv6 link local
packets. However, it only works for UDP and worse TCP connection attempts
to the LLA with the only listener bound to the VRF just hang where as
before the client gets a reset and connection refused. Fix by adjusting
ir_iif for LL addresses and packets received through a device enslaved
to a VRF.

Fixes: 6f12fa77 ("vrf: mark skb for multicast or link-local as enslaved to VRF")
Reported-by: NDonald Sharp <sharpd@cumulusnetworks.com>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve detection of spurious interrupts by checking against the
interrupt mask as currently set in the chip.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already have the DEFINE_SHOW_ATTRIBUTE. There is no need to define
such a macro, so remove DEFINE_SIMPLE_DEBUGFS_FILE. Also use the
DEFINE_SHOW_ATTRIBUTE macro to simplify some code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
net: hns3: Add more commands to Debugfs in HNS3 driver

This patch-set adds few more debugfs commands to HNS3 Ethernet
Driver. Support has been added to query info related to below
items:
1. Packet buffer descriptor ("echo bd info [queue no] [bd index] > cmd")
2. Manager table("echo dump mng tbl > cmd")
3. Dfx status register("echo dump reg ssu [prt id] > cmd")
4. Dcb status register("echo dump reg dcb [port id] > cmd")
5. Queue map ("echo queue map [queue no] > cmd")
6. Tm map ("echo tm map [queue no] > cmd")

NOTE: Above commands are *read-only* and are only intended to
query the information from the SoC(and dump inside the kernel,
for now) and in no way tries to perform write operations for
the purpose of configuration etc.

Change Log:
V1-->V2:
1. Addressed the GCC-8.2 compiler issue reported by David S. Miller.
   Link: https://lkml.org/lkml/2018/12/14/1298
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prints dcb register status  information by module.

debugfs command:
root@(none)# echo dump tm map 100 > cmd
queue_id | qset_id | pri_id | tc_id
0100     | 0065    | 08     | 00
root@(none)#
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prints queue map information.

debugfs command:
echo dump queue map > cmd

Sample Command:
root@(none)# echo queue map > cmd
 local queue id | global queue id | vector id
          0              32             769
          1              33             770
          2              34             771
          3              35             772
          4              36             773
          5              37             774
          6              38             775
          7              39             776
          8              40             777
          9              41             778
         10              42             779
         11              43             780
         12              44             781
         13              45             782
         14              46             783
         15              47             784
root@(none)#
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prints dcb register status  information by module.

debugfs command:
root@(none)# echo dump reg dcb > cmd
 roce_qset_mask: 0x0
 nic_qs_mask: 0x0
 qs_shaping_pass: 0x0
 qs_bp_sts: 0x0
 pri_mask: 0x0
 pri_cshaping_pass: 0x0
 pri_pshaping_pass: 0x0
root@(none)#
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prints status register information by module.

debugfs command:
echo dump reg [mode name] > cmd

Sample Command:
root@(none)# echo dump reg bios common > cmd
 BP_CPU_STATE: 0x0
 DFX_MSIX_INFO_NIC_0: 0xc000
 DFX_MSIX_INFO_NIC_1: 0xf
 DFX_MSIX_INFO_NIC_2: 0x2
 DFX_MSIX_INFO_NIC_3: 0x2
 DFX_MSIX_INFO_ROC_0: 0xc000
 DFX_MSIX_INFO_ROC_1: 0x0
 DFX_MSIX_INFO_ROC_2: 0x0
 DFX_MSIX_INFO_ROC_3: 0x0
root@(none)#
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prints manager table information.

debugfs command:
echo dump mng tbl > cmd

Sample Command:
root@(none)# echo dump mng tbl > cmd
 entry|mac_addr         |mask|ether|mask|vlan|mask|i_map|i_dir|e_type
 00   |01:00:5e:00:00:01|0   |00000|0   |0000|0   |00   |00   |0
 01   |c2:f1:c5:82:68:17|0   |00000|0   |0000|0   |00   |00   |0
root@(none)#
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prints Sending and receiving
package descriptor information.

debugfs command:
echo dump bd info 1 > cmd

Sample Command:
root@(none)# echo bd info 1 > cmd
hns3 0000:7d:00.0: TX Queue Num: 0, BD Index: 0
hns3 0000:7d:00.0: (TX) addr: 0x0
hns3 0000:7d:00.0: (TX)vlan_tag: 0
hns3 0000:7d:00.0: (TX)send_size: 0
hns3 0000:7d:00.0: (TX)vlan_tso: 0
hns3 0000:7d:00.0: (TX)l2_len: 0
hns3 0000:7d:00.0: (TX)l3_len: 0
hns3 0000:7d:00.0: (TX)l4_len: 0
hns3 0000:7d:00.0: (TX)vlan_tag: 0
hns3 0000:7d:00.0: (TX)tv: 0
hns3 0000:7d:00.0: (TX)vlan_msec: 0
hns3 0000:7d:00.0: (TX)ol2_len: 0
hns3 0000:7d:00.0: (TX)ol3_len: 0
hns3 0000:7d:00.0: (TX)ol4_len: 0
hns3 0000:7d:00.0: (TX)paylen: 0
hns3 0000:7d:00.0: (TX)vld_ra_ri: 0
hns3 0000:7d:00.0: (TX)mss: 0
hns3 0000:7d:00.0: RX Queue Num: 0, BD Index: 120
hns3 0000:7d:00.0: (RX)addr: 0xffee7000
hns3 0000:7d:00.0: (RX)pkt_len: 0
hns3 0000:7d:00.0: (RX)size: 0
hns3 0000:7d:00.0: (RX)rss_hash: 0
hns3 0000:7d:00.0: (RX)fd_id: 0
hns3 0000:7d:00.0: (RX)vlan_tag: 0
hns3 0000:7d:00.0: (RX)o_dm_vlan_id_fb: 0
hns3 0000:7d:00.0: (RX)ot_vlan_tag: 0
hns3 0000:7d:00.0: (RX)bd_base_info: 0
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Peter Oskolkov says:

====================
net: prefer listeners bound to an address

A relatively common use case is to have several IPs configured
on a host, and have different listeners for each of them. We would
like to add a "catch all" listener on addr_any, to match incoming
connections not served by any of the listeners bound to a specific
address.

However, port-only lookups can match addr_any sockets when sockets
listening on specific addresses are present if so_reuseport flag
is set. This patchset eliminates lookups into port-only hashtable,
as lookups by (addr,port) tuple are easily available.

In a future patchset I plan to explore whether it is possible
to remove port-only hashtables completely: additional refactoring
will be required, as some non-lookup code uses the hashtables.
====================
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a selftest that verifies that a socket listening
on a specific address is chosen in preference over sockets
that listen on any address. The test covers UDP/UDP6/TCP/TCP6.

It is based on, and similar to, reuseport_dualstack.c selftest.
Signed-off-by: NPeter Oskolkov <posk@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>