Merge tag 'actions-arm64-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt

Pull "Actions Semi ARM64 based SoC DT for v4.15" from Andreas Färber:

This updates the Bubblegum-96 DT with a clock node for the debug UART.

* tag 'actions-arm64-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
  arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock

Merge tag 'actions-arm-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt

Pull "Actions Semi ARM based SoC DT for v4.15" from Andreas Färber:

This updates the Guitar board DT with a clock node for the debug UART
and adds a new DT for the CubieBoard6.
It also updates the S500 DT with CPU power domains.

* tag 'actions-arm-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
  ARM: dts: owl-s500: Add CubieBoard6
  dt-bindings: arm: actions: Add CubieBoard6
  ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
  ARM: dts: owl-s500: Set power domains for CPU2 and CPU3

Give the serial driver a fixed-clock as input for baudrate 115200.
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Add a Device Tree for Cubietech CubieBoard6.

Cc: support@cubietech.com
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Define a compatible string for Cubietech CubieBoard6.

Cc: support@cubietech.com
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Add a fixed-clock for baudrate 115200.
Signed-off-by: NAndreas Färber <afaerber@suse.de>

CPU2 has its own power domain PD_CPU2, and CPU3 has PD_CPU3.
Signed-off-by: NAndreas Färber <afaerber@suse.de>

Merge tag 'socfpga_dts_for_v4.15_part2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

Pull "SoCFPGA DTS updates for v4.15, part 2" from Dinh Nguyen:

- Stratix10 platform update
  - Enable GPIO and LEDs for Stratix10 devkit

* tag 'socfpga_dts_for_v4.15_part2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  arm64: dts: stratix10: fix interrupt number for gpio1
  arm64: dts: stratix10: enable gpio and leds
  arm64: dts: stratix10: add gpio header

Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 64-bit DT updates for v4.15, round 2" from Kevin Hilman:
- add support for new GPIO IRQ driver

* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gx: add external PHY interrupt on some platforms
  ARM64: dts: meson-gx: add gpio interrupt controller
  ARM64: meson: enable MESON_IRQ_GPIO in Kconfig
  ARM64: dts: meson-gxbb-odroidc2: fix usb1 power supply

Merge tag 'imx-dt64-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Pull "Freescale arm64 device tree updates for 4.15" from Shawn Guo:

 - Add GICv3 ITS node and PCIe devcies for LS1088A support.
 - Enable PCIe support for LS2088A SoC.
 - Add OP-TEE support for various Layerscape SoCs, LS1012A, LS1043A,
   LS1046A, LS1088A and LS208XA.
 - Update DPAA QBMan nodes to use constant defines in the interrupt
   description.
 - Add DSPI device to support SPI-NOR on LS1012A based boards.

* tag 'imx-dt64-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: update the DPAA QBMan nodes
  arm64: dts: ls1088a: add PCIe controller DT nodes
  arm64: dts: ls1088a: add gicv3 ITS DT node
  arm64: dts: ls2088a: add pcie support
  arm64: dts: ls: Add optee node
  dt-bindings: mtd: add sst25wf040b and en25s64 to sip-nor list
  dt-bindings: spi: Add fsl,ls1012a-dspi compatible string
  arm64: dts: ls1012a: add the DTS node for DSPI support

Pull "Mediatek: 64-bit DT update for v4.15" from Matthias Brugger:

- mt2712: add cpuidle support

* tag 'v4.14-next-dts64' of https://github.com/mbgg/linux-mediatek:
  arm64: dts: mediatek: Add cpuidle support for MT2712

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 64-bit platforms: DT updates for v4.15" from Kevin Hilman:

- new SoC support: A113D
- new boards: Tronsmart Vega S96, Khadas vim2
- reserved memory fixups
- gpio-names cleanups
- MMC cleanups, enable high-speed modes
- misc cleanups

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: dts: meson-axg: add initial A113D SoC DT support
  dt-bindings: arm: amlogic: Add Meson AXG binding
  ARM64: dts: meson-gx: remove unnecessary uart compatible
  ARM64: dts: meson-gx: remove unnecessary clocks properties
  ARM64: dts: meson-gxl: Add alternate ARM Trusted Firmware reserved memory zone
  ARM64: dts: meson-gxm: enable HS400 on the vim2
  ARM64: dts: meson-gxbb-nexbox-a95x: Enable USB Nodes
  dt-bindings: arm: amlogic: Add Tronsmart Vega S96 binding
  ARM64: dts: meson-gxm: Add Vega S96 board
  ARM64: dts: meson-gxm: Add support for Khadas VIM2
  ARM64: dts: meson-gxl: Take eMMC data strobe out of eMMC pins
  ARM64: dts: meson-gxl: adjust libretech-cc gpio-line-names
  ARM64: dts: meson-gxl: adjust kvim gpio-line-names
  ARM64: dts: meson-gxbb: adjust odroid-c2 gpio-line-names
  ARM64: dts: meson-gxbb: adjust nanopi-k2 gpio-line-names
  ARM64: dts: meson-gx: adjust gpio-ranges for TEST_N
  ARM64: dts: meson-gx: remove gpio offset
  ARM: dts: meson8: remove gpio offset
  ARM64: dts: meson-gxl-libretech-cc: enable internal phy leds
  ARM64: dts: meson-gxl-libretech-cc: enable saradc

Pull "mvebu dt64 for 4.15 (part 1)" from Gregory CLEMENT:

On Armada 7K/8k:
- Improve network support at SoC and board level
- Enable watchdog
- Add UART muxing
- On 7040 DB: add CD SDIO and NAND support
- On 8040 DB: add PCIE more ports and SPI1

On Armada 37xx:
 - Fix UART register size
 - Add vmmc regulator for SD on 3720 DB

* tag 'mvebu-dt64-4.15-1' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: 7040-db: Add the carrier detect pin for SD card on CP
  arm64: dts: marvell: 7040-db: Document the gpio expander
  arm64: dts: marvell: enable additional PCIe ports on Armada 8040 DB
  arm64: dts: marvell: add NAND support on the 7040-DB board
  arm64: dts: marvell: Enable Armada-8040-DB CPS SPI1
  arm64: dts: marvell: 8040-db: enable the SFP ports
  arm64: dts: marvell: 7040-db: enable the SFP port
  arm64: dts: marvell: 7040-db: add comphy reference to Ethernet port
  arm64: dts: marvell: mcbin: add comphy references to Ethernet ports
  arm64: dts: marvell: 37xx: remove empty line
  arm64: dts: marvell: cp110: add PPv2 port interrupts
  arm64: dts: marvell: add comphy nodes on cp110 master and slave
  arm64: dts: marvell: extend the cp110 syscon register area length
  arm64: dts: marvell: enable AP806 watchdog
  arm64: dts: marvell: Fix A37xx UART0 register size
  arm64: dts: marvell: armada-3720-db: Add vmmc regulator for SD slot
  arm64: dts: marvell: add UART muxing on Armada 7K/8K

Merge tag 'tegra-for-4.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "arm64: tegra: Device tree changes for v4.15-rc1" from Thierry Reding:

Enables host1x, VIC, PCIe and the BPMP thermal sensor on Tegra186.

* tag 'tegra-for-4.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  arm64: tegra: Add BPMP thermal sensor to Tegra186
  arm64: tegra: Enable PCIe on Jetson TX2
  arm64: tegra: Add PCIe node for Tegra186
  arm64: tegra: Add VIC on Tegra186
  arm64: tegra: Add host1x on Tegra186
  arm64: tegra: Add #power-domain-cells for BPMP

Merge tag 'renesas-arm64-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Second Round of Renesas ARM64 Based SoC DT Updates for v4.15" from Simon Horman:

* r8a7795 (H3) and r8a7796 (M3-W) SoCs
  - Use R-Car Gen 3 fallback compat string for GPIO

    Simon Horman says "Use newly added R-Car GPIO Gen 1, 2 and 3 fallback
    compat strings in peace of now deprecated non-generation specific R-Car
    GPIO fallback compat string in the DT of Renesas ARM and arm64 based
    SoCs.

* r8a7795 (H3) and r8a7796 (M3-W) Salvator boards
  - Add dr_mode property for USB2.0 channel 0

    Shimoda-san says "Since Salvator-X[S] have a USB2.0 dual-role channel
    (CN9), this patch
    adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
    as "otg".

    Using dual-role channel (or not) is related to the type of USB receptor
    on board specification. So, I added the property into the
    salvator-common.dtsi."

  - Add pfc node for USB3.0 channel 0

    Shimoda-san says "Since a R-Car Gen3 bootloader enables the PFC of
    USB3.0 channel 0, the USB3.0 host controller works without this setting
    on the kernel.  But, this setting should have salvator-common.dtsi. So,
    this patch adds the pfc node for USB3.0 channel 0."

* r8a7795 (H3) and r8a7796 (M3-W) Salvator and ULCB boards
  - Correct audio_clkout

    Morimoto-san says ""audio_clkout" is dummy clock of <&rcar_sound 0> to
    avoid clock loop which invites probe conflct. Thus <&rcar_sound 0> and
    "audio_clkout" should be same value."

* r8a7795 (H3) and r8a7796 (M3-W) Salvator and ULCB, and
  r8a77995 (D3) Draak boards
  - Drop "avb_phy_int" from avb_pins

    Shimoda-san says "Since the Ethernet AVB driver doesn't support
    AVB_PHY_INT handling and it will be handled by a phy driver as a gpio
    pin, this patch removes the "avb_phy_int" from the avb_pins node."

* r8a77995 (D3) Draak board
  - Enable PWM channels

    Shimoda-san says "Each channel connects to LTC2644 for brightness
    control."

* r8a77970 (V3M) Eagle and ULCB Kingfisher boards
  - Add initial device tree support

* tag 'renesas-arm64-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
  arm64: dts: renesas: salvator-common: add dr_mode property for USB2.0 channel 0
  arm64: dts: r8a7796: Use R-Car GPIO Gen3 fallback compat string
  arm64: dts: r8a7795: Use R-Car GPIO Gen3 fallback compat string
  arm64: renesas: ulcb: fixup audio_clkout
  arm64: renesas: salvator-common: fixup audio_clkout
  arm64: dts: renesas: eagle: add EtherAVB support
  arm64: dts: r8a77995: Add INTC-EX device node
  arm64: dts: r8a77970: Add INTC-EX device node
  arm64: dts: r8a7796: Add INTC-EX device node
  arm64: dts: ulcb-kf: hog USB3 hub control gpios
  arm64: dts: ulcb-kf: enable PCA9548 on I2C4
  arm64: dts: ulcb-kf: enable PCA9548 on I2C2
  arm64: dts: ulcb-kf: enable TCA9539 on I2C4
  arm64: dts: ulcb-kf: enable TCA9539 on I2C2
  arm64: dts: ulcb-kf: enable USB3.0 Host
  arm64: dts: ulcb-kf: enable PCIE0/1
  arm64: dts: ulcb-kf: enable USB2.0 Host channel 0
  arm64: dts: ulcb-kf: enable HSUSB
  arm64: dts: ulcb-kf: enable CAN0/1
  arm64: dts: ulcb-kf: enable SCIF1
  ...

Merge tag 'uniphier-dt64-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

Pull "UniPhier ARM64 SoC DT updates for v4.15" from Masahiro Yamada:

- add thermal monitor and thermal zone nodes
- add efuse nodes
- fix W=2 warnings
- add GPIO controller nodes and related properties
- add resets properties

* tag 'uniphier-dt64-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  arm64: dts: uniphier: add resets properties
  arm64: dts: uniphier: add eMMC hardware reset provider node
  arm64: dts: uniphier: add GPIO hog definition
  arm64: dts: uniphier: route on-board device IRQ to GPIO controller
  arm64: dts: uniphier: add GPIO controller nodes
  arm64: dts: uniphier: fix W=2 build warnings
  arm64: dts: uniphier: enable NAND for PXs3 reference board
  arm64: dts: uniphier: add efuse node for LD11, LD20, and PXs3
  arm64: dts: uniphier: add nodes of thermal monitor and thermal zone for LD20

Merge tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner arm64 DT changes for 4.15" from Maxime Ripard:

Most notable changes:
  - SPI and DMA support on the a64
  - New boards: NanoPi NEO Plus2

* tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm: allwinner: Correct unit name in devicetree binding example
  arm64: allwinner: a64: add dma controller references to spi nodes
  arm64: allwinner: a64: Add device node for DMA controller
  arm64: allwinner: a64: Fix node with unit name and no reg property
  arm64: allwinner: a64: Fix simple-bus unit address format error
  arm64: allwinner: h5: add NanoPi NEO Plus2 DT support
  arm64: allwinner: a64: add SPI nodes

Merge tag 'amlogic-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 32-bit DT updates for v4.15, round 2" from Kevin Hilman:
- enable new GPIO IRQ controller
- add efuse node

* tag 'amlogic-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson: add the efuse node
  ARM: dts: meson8b: enable gpio interrupt controller
  ARM: dts: meson8b: add support for booting the secondary CPU cores
  ARM: dts: meson8: add support for booting the secondary CPU cores

Merge tag 'at91-ab-4.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt

Pull" ARM: at91: DT for 4.15" from Alexandre Belloni:

 - sama5d2 xplained: add charger and SD card power supply
 - sama5d27_som1_ek: many adjustments
 - at91sam9x25ek: add pwm0 and can1

* tag 'at91-ab-4.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  ARM: dts: at91: at91sam9x5ek: use DMA for USART0
  ARM: dts: at91: at91sam9x25ek: add pwm0
  ARM: dts: at91: at91sam9x25ek: add CAN1 interface
  ARM: dts: at91: sama5d2_xplained: remove pull-up on SD/MMC lines
  ARM: dts: at91: sama5d2_xplained: add pinmuxing for pwm0
  ARM: dts: at91: sama5d2_xplained: set PB_USER as wakeup source
  ARM: dts: at91: sama5d27_som1_ek: remove pull-up on SD/MMC lines
  ARM: dts: at91: sama5d27_som1_ek: remove not connected CAN0
  ARM: dts: at91: sama5d27_som1_ek: add pinmuxing for pwm0
  ARM: dts: at91: sama5d27_som1_ek: add aliases for i2c
  ARM: dts: at91: sama5d27_som1_ek: set USER button as a wakeup source
  ARM: dts: at91: sama5d27_som1_ek: update serial aliases
  ARM: dts: at91: sama5d27_som1_ek: enable i2c2
  ARM: dts: at91: sama5d27_som1_ek: add disabled status
  ARM: dts: at91: usb_a9g20: fix rtc node
  ARM: dts: at91: sama5d2 Xplained: Describe the SD card power supply
  ARM: dts: at91: sama5d2_xplained: Add charger node

Merge tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt

Pull "i.MX device tree updates for 4.15" from Shawn Guo:

 - New board support: i.MX51 ZII RDU1, i.MX53 GE Healthcare PPD, i.MX6
   TX modules for MB7 from  Ka-Ro Electronics, i.MX6 Wandboard revd1
   variants, i.MX6 LWN DISPLAY5 board, Pistachio i.MX6Q board, i.MX6SX
   Vining-2000 board.
 - Use the 'vpcie-supply' property for PCIe device for boards
   imx6qdl-sabresd, imx6q-novena and imx6q-cm-fx6.
 - A series from Jagan Teki to update imx6qdl-icore board with audio,
   touch and CAN support.
 - Switch to nvmem for accessing OCOTP from tempmon for i.MX6SX and add
   tempmon support for i.MX6UL.
 - A bunch of patches from Lothar Waßmann updating Ka-Ro i.MX28, i.MX53
   and i.MX6 TX modules.
 - Fix DTC warnings in i.MX device trees, dropping leading zeros from
   unit address, correcting display nodes notation and display port
   names, fixing nodes with unit name and no reg property.
 - Other random device updates for various board support.

* tag 'imx-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
  ARM: dts: imx53-tx53: fix interrupt flags
  ARM: dts: imx28-tx28: fix interrupt flags
  ARM: dts: display5: Device tree description of LWN's DISPLAY5 board
  ARM: dts: imx53-qsb-common: Fix 'led_gpio7_7@0' node with unit name and no reg property
  ARM: dts: imx53-m53evk: Fix 'led_gpio@0' node with unit name and no reg property
  ARM: dts: imx53: Fix 'usbphy@x' node with unit name and no reg property
  ARM: dts: imx51-ts4800: Fix 'port@0' node with unit name and no reg property
  ARM: dts: imx51-apf51dev: Fix 'backlight@bl1' node with unit name and no reg property
  ARM: dts: imx: add ZII RDU1 board
  ARM: dts: imx: add support for TX6 modules on MB7 baseboard
  ARM: dts: imx: add support for TX6QP
  ARM: dts: imx6-tx6: add a .dtsi file for the MB7 baseboard
  ARM: dts: imx6-tx6: move display configuration to .dtsi file
  ARM: dts: imx6-tx6: add support for I2C bus recovery
  ARM: dts: imx6-tx6: convert to using simple-audio-card
  ARM: dts: imx6-tx6: specify ethernet phy reset post-delay
  ARM: dts: imx6-tx6: improve ethernet related pinctrl setup
  ARM: dts: imx6-tx6: add trickle-charge config for DS1339
  ARM: dts: imx6-tx6: remove obsolete ipu1 alias
  ARM: dts: imx6-tx6: remove obsolete eeti,egalax_ts
  ...

[arnd: made sure we have no new leading zeroes in unit address during merge]

Merge tag 'uniphier-dt-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt

Pull "UniPhier ARM SoC DT updates for v4.15" from Masahiro Yamada:

- add thermal monitor and thermal zone nodes
- fix W=2 warnings
- add GPIO controller nodes and related properties
- add resets properties

* tag 'uniphier-dt-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
  ARM: dts: uniphier: add resets properties
  ARM: dts: uniphier: add GPIO hog definition
  ARM: dts: uniphier: route on-board device IRQ to GPIO controller
  ARM: dts: uniphier: add GPIO controller nodes
  ARM: dts: uniphier: fix W=2 build warnings
  ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for PXs2

Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt

Pull "Amlogic 32-bit platforms: DT updates for v4.15"

- add SDIO MMC controller
- reserved memory fixes
- SoC info driver nodes
- enable USB host controller

* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM: dts: meson: add the SDIO MMC controller
  ARM: dts: meson8b: add reserved memory zone to fix silent freezes
  ARM: dts: meson: add SoC information nodes
  dt-bindings: Amlogic: add documentation for the SoC info register areas
  ARM: dts: meson: fixing USB support on Meson6, Meson8 and Meson8b
  ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ board

Merge tag 'keystone_dts_for_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt

Pull "ARM: Keystone DTS update for 4.15" from Santosh Shilimkar:

- McASP support for K2G EVM
- I2C support for K2G EVM
- USB support for K2G EVM
- SPI & SPI NOR flash support for K2G EVM
- ECAP PWM support for K2G EVM

* tag 'keystone_dts_for_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone-k2g-evm: add bindings for SPI NOR flash
  ARM: dts: keystone-k2g: Add SPI nodes
  ARM: dts: keystone-k2g-evm: Enable PWM ECAP0
  ARM: dts: keystone-k2g: Add ECAP PWM DT nodes
  ARM: dts: k2g-evm: Enable USB 0 and 1
  ARM: dts: k2g: Add USB instances
  ARM: dts: keystone-k2g-evm: Add I2C EEPROM DT entry
  ARM: dts: keystone-k2g: Add I2C nodes
  ARM: dts: keystone-k2g: Add McASP nodes

Pull "Broadcom devicetree changes for 4.15" from Florian Fainelli:

This pull request contains Broadcom ARM-based Device Tree changes for 4.15,
please pull the following:

- Eric adds support for the CLCD and PWM controller on Cygnus chis

- Loic fixes the console path on the Raspberry Pi 3 (already submitted as
  fixes) and then proceeds with enabling the BCM43438 bluetooth chip on
  the Raspberry Pi 3

- Rafal specifies the USB ports on the Luxul XWR-1200

- Dan adds support for the Luxul ABR-4500 based on BCM47094, the Luxul XAP-810
  and XAP-1440 both based on BCM53573

- Florian adds support for the Broadcom Hurricane 2 SoC by adding general
  machine binding, clock binding, SoC DTS include file and a DTS for the
  Ubiquiti Networks UniFi Switch 8

* tag 'arm-soc/for-4.15/devicetree' of http://github.com/Broadcom/stblinux:
  ARM: dts: Hurricane 2: Add basic support for Ubiquiti UniFi Switch 8
  dt-bindings: Add Ubiquiti Networks vendor prefix
  ARM: dts: Add Broadcom Hurricane 2 DTS include file
  dt-bindings: Document Broadcom Hurricane 2 clocks
  dt-bindings: Add documentation for Broadcom Hurricane 2 SoCs
  ARM: dts: BCM53573: Add DT for Luxul XAP-1440
  ARM: dts: BCM53573: Add DT for Luxul XAP-810
  ARM: dts: BCM5301X: Add DT for Luxul ABR-4500
  ARM: dts: BCM5301X: Add DT for Luxul XBR-4500
  ARM: dts: BCM5301X: Specify USB ports for USB LED of Luxul XWR-1200
  ARM: dts: bcm2837-rpi-3-b: Add bcm43438 serial slave
  ARM: dts: bcm283x: Fix console path on RPi3
  ARM: dts: cygnus: Add the PWM node
  ARM: dts: cygnus: Add the CLCD controller

Merge tag 'tegra-for-4.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "ARM: tegra: Device tree changes for v4.15-rc1" from Thierry Reding:

Adds support for the CEC controller found on Tegra124 and enables it on
Tegra K1.

* tag 'tegra-for-4.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Enable CEC support on Jetson TK1
  ARM: tegra: Add CEC support for Tegra124

Merge tag 'tegra-for-4.15-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Pull "dt-bindings: Updates for v4.15-rc1" from Thierry Reding:

This contains the addition of a clock alias which will be used to fix
the implementation of the SOR1 clock.

Also included are the bindings for the Tegra186 BPMP thermal driver, a
prerequisite for both the driver and device tree changes.

* tag 'tegra-for-4.15-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  dt-bindings: Add bindings for nvidia,tegra186-bpmp-thermal
  dt-bindings: clock: tegra: Add sor1_out clock

Merge tag 'renesas-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.15" from Simon Horman:

* r8a77430 (RZ/G1M) SoC
  - Add XHCI support to SoC DT. Boards may enable this as appropriate

* All Renesas ARM based SoCs
  - Add missing clocks for ARM CPU cores

    Geert Uytterhoeven says "This series improves DT hardware descriptions
    for Renesas arm32 SoCs by adding missing clocks properties to the
    device nodes corresponding to ARM CPU cores."

* R-Car Gen 1 and 2, and RZ/G SoCs
  - Use R-Car Fallback compat strings for GPIO

    Simon Horman says "Use newly added R-Car GPIO Gen 1, 2 and 3 fallback
    compat strings in peace of now deprecated non-generation specific R-Car
    GPIO fallback compat string in the DT of Renesas ARM and arm64 based
    SoCs.

    As noted in the changelogs for the r8a777[89] changes, this introduces
    an incompatibility with pre-v4.14 kernels used with new DTBs. There is
    no run-time effect for other SoCs updated by this changeset."

* r7s72100 (RZ/A1H) GR-Peach board
  - Add pin configuration subnode for ETHER pin group.
    This avoids relying on boot-loader configuration of these pins.

  - Enable ostm0 and ostm1 timers

    Jacopo Mondi says these are "to be used as clock source and clockevent
    source. The timers provides greater accuracy than the already enabled
    mtu2 one."

  - Correct leds node name indent

  - Enable MTU2 timer pulse unit

   Jacopo Mondi says "MTU2 multi-function/multi-channel timer/counter is
   not enabled for GR-Peach board. The timer is used as clock event source
   to schedule wake-ups, and without this enabled all sleeps not performed
   through busy waiting hang the board."

* r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
  - Add USB function support

* r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
  - Add USB2.0 Host support

* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform
  - Rework DT architecture and add DT for camera DB

    Fabrizio Castro says "Some of the serial interfaces are exposed on the
    camera daughter board.  The camera daughter board can be connected to
    the carrier board by means of expansion connectors 1, 2 and 3. The
    carrier board may host an RZ/G1M or an RZ/G1N based SoM.

    While adding support for the serial interfaces on the camera daughter
    board we faced the dilemma of how to properly describe all of the
    possible HW configurations and how to maximize code reuse.

    The best option would be to use device tree overlays, however there is
    still some work to be done on that front before actually using them,
    therefore for the time being we decided to provide .dtsi files to
    describe the carrier board and the camera daughter board, and provide
    .dts files to describe the HW configurations we need to support."

* r8a779[0-4] R-Car Gen2 SoCs
  - Use generic node name for VSP1 nodes

    Geert Uytterhoeven says "This patch series replaces the specific node
    names used for the VSP1 nodes by the preferred generic node names, cfr.
    commit 0e1bfb72 ("v4l: vsp1: Use generic node name")."

* tag 'renesas-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (42 commits)
  ARM: dts: r8a7743: Add xhci support to SoC dtsi
  ARM: dts: r7s72100: Add clock for CA9 CPU core
  dt-bindings: clk: r7s72100: Add missing I and G clocks
  ARM: dts: sh73a0: Add clocks for CA9 CPU cores
  ARM: dts: r8a7794: Add missing clock for secondary CA7 CPU core
  ARM: dts: r8a7793: Add missing clock for secondary CA15 CPU core
  ARM: dts: r8a7792: Add missing clock for secondary CA15 CPU core
  ARM: dts: r8a7791: Add missing clock for secondary CA15 CPU core
  ARM: dts: r8a7790: Add clocks for CA7 CPU cores
  ARM: dts: r8a7790: Add missing clocks for secondary CA15 CPU cores
  ARM: dts: r8a7779: Add clocks for CA9 CPU cores
  ARM: dts: r8a7778: Add clock for CA9 CPU core
  ARM: dts: r8a7743: Add missing clock for secondary CA15 CPU core
  ARM: dts: r8a73a4: Add clock for CA15 CPU0 core
  ARM: dts: r8a7794: Use R-Car GPIO Gen2 fallback compat string
  ARM: dts: r8a7793: Use R-Car GPIO Gen2 fallback compat string
  ARM: dts: r8a7792: Use R-Car GPIO Gen2 fallback compat string
  ARM: dts: r8a7791: Use R-Car GPIO Gen2 fallback compat string
  ARM: dts: r8a7790: Use R-Car GPIO Gen2 fallback compat string
  ARM: dts: r8a7743: Use R-Car GPIO Gen2 fallback compat string
  ...

Merge tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner DT changes for 4.15" from Maxime Ripard:

The most notable changes are:
  - Conversion to the last SoC (A10, A20) to the new clock framework
  - HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
  - Support for the various power supplies on a number of boards
  - Fix of DTC warnings on a number of SoCs, but most of them still need
    some work
  - New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
    Banana Pi M2 Ultra
  - New R40 SoC support

* tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (63 commits)
  ARM: sun8i: r40: enable USB host for Banana Pi M2 Ultra
  ARM: sun8i: v40: add 5V regulator for Banana Pi M2 Berry
  ARM: sun8i: r40: add 5V regulator for Banana Pi M2 Ultra
  ARM: sun8i: r40: add USB host port nodes for R40
  ARM: dts: sun4i: Enable HDMI support on some A10 devices
  ARM: dts: sun7i: Enable HDMI support on some A20 devices
  ARM: dts: sun7i: Add device nodes for display pipelines
  ARM: dts: sun4i: Add device nodes for display pipelines
  ARM: dts: sun8i: r40: add watchdog device node
  ARM: dts: sun5i: reference-design-tablet: Enable AXP209 AC and battery
  ARM: dts: sun9i: Change node names to remove underscores
  ARM: dts: sun9i: Change node names to remove underscores
  ARM: dts: sun4i: Remove underscores from nodes names
  ARM: dts: sun4i: Provide default muxing for relevant controllers
  ARM: dts: sun4i: Change pinctrl nodes to avoid warning
  ARM: dts: sun6i: Enable HDMI support on some A31/A31s devices
  ARM: dts: sun6i: Add device node for HDMI controller
  ARM: dts: sun4i: Change LRADC node names to avoid warnings
  ARM: dts: sun4i: Remove skeleton and memory to avoid warnings
  ARM: dts: sun4i: Remove gpio-keys warnings
  ...

Meson6, Meson8 and Meson8b use a similar IP block which has access to
512 bytes of efuse data.
During SoC manufacturing some calibration settings for the CVBS
connector and the internal temperature sensor are written to this efuse.
On some boards it additionally stores for example the MAC addresses.

The efuse is enabled on Meson8 and Meson8b but kept disabled on Meson6
since we do not have a clock driver there (which is required to read
data from the efuse).
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add gpio interrupt controller node to the meson8b boards
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add the external PHY interrupt on the nanopi-k2, odroid-c2, p200, p230
and q200
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Add gpio interrupt controller to Amlogic GX family SoCs
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

select MESON_IRQ_GPIO in Kconfig for Amlogic's meson SoC family
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Looking at the schematics, the USB Power Supply is shared between the
two USB interfaces,
If the usb0 fails to initialize, the second one won't have power.

Fixes: 5a0803bd ("ARM64: dts: meson-gxbb-odroidc2: Enable USB Nodes")
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Booting the secondary CPU cores involves the following nodes/devices:
- SCU (Snoop-Control-Unit, for which we already have a DT node)
- a reset line for each CPU core, provided by the reset-controller
  which is built into the clock-controller
- the PMU (power management unit) which controls the power of the CPU
  cores
- a range in the SRAM specifically reserved for booting secondary CPU
  cores
- the "enable-method" which activates booting the secondary CPU cores

This adds all required nodes and properties to boot the secondary CPU
cores.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NLinus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Booting the secondary CPU cores involves the following nodes/devices:
- SCU (Snoop-Control-Unit, for which we already have a DT node)
- a reset line for each CPU core, provided by the reset-controller
  which is built into the clock-controller
- the PMU (power management unit) which controls the power of the CPU
  cores
- a range in the SRAM specifically reserved for booting secondary CPU
  cores
- the "enable-method" which activates booting the secondary CPU cores

This adds all required nodes and properties to boot the secondary CPU
cores.
Suggested-by: NCarlo Caione <carlo@caione.org>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

Some interrupts properties are given '0' as the flags argument or no
flags argument at all.
Change them to use the appropriate interrupt flags.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Some interrupts properties are given '0' as the flags argument.
Change them to use the appropriate interrupt flags.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add resets properties to all nodes that have reset lines.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Add resets properties to all nodes that have reset lines.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>