Newly added code in the bnxt driver uses a couple of variables that
are never initialized when CONFIG_BNXT_SRIOV is not set, and gcc
correctly warns about that:

In file included from include/linux/list.h:8:0,
                 from include/linux/module.h:9,
                 from drivers/net/ethernet/broadcom/bnxt/bnxt.c:10:
drivers/net/ethernet/broadcom/bnxt/bnxt.c: In function 'bnxt_get_max_rings':
include/linux/kernel.h:794:26: warning: 'cp' may be used uninitialized in this function [-Wmaybe-uninitialized]
include/linux/kernel.h:794:26: warning: 'tx' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/broadcom/bnxt/bnxt.c:5730:11: warning: 'rx' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/broadcom/bnxt/bnxt.c:5736:6: note: 'rx' was declared here

This changes the condition so that we fall back to using the PF
data if VF is not available, and always initialize the variables
to something useful.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 6e6c5a57 ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.")
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The offset inside the fragment was not used for the dma address and
silent data corruption resulted because TSO makes the checksum match.

Fixes: 077742da ("dwc_eth_qos: Add support for Synopsys DWC Ethernet QoS")
Signed-off-by: NLars Persson <larper@axis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It used to be that bus->irq was a pointer but after e7f4dc35
('mdio: Move allocation of interrupts into core') it's an array inside
the mdio struct, so it can never be NULL.  Let's remove the check.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It used to be that mdio->irq was a pointer but after e7f4dc35
('mdio: Move allocation of interrupts into core') it's an array inside
the mdio struct so it can never be NULL.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If bus = kzalloc() fails then we end up dereferencing bus when we do
"bus->irq[i] = PHY_POLL;".  The code is a little simpler if we reverse
the NULL check and return directly on failure.

Fixes: e7f4dc35 ('mdio: Move allocation of interrupts into core')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev has moved inside the new mdio structure.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev has moved inside the new mdio structure.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 1f718f0f ("bonding: populate neighbour's private on enslave")
undoes the fix provided by commit c2edacf8 ("bonding / ipv6: no addrconf
for slaves separately from master") by effectively setting the slave flag
after the slave has been opened.  If the slave comes up quickly enough, it
will go through the IPv6 addrconf before the slave flag has been set and
will get a link local IPv6 address.

In order to ensure that addrconf knows to ignore the slave devices on state
change, set IFF_SLAVE before dev_open() during bonding enslavement.

Fixes: 1f718f0f ("bonding: populate neighbour's private on enslave")
Signed-off-by: NKarl Heiss <kheiss@gmail.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding flow steering support by creating a flow-table per
priority (if rules exist in the priority). mlx5_ib uses
autogrouping and thus only creates the required destinations.

Also includes adding of these flow steering utilities

1. Parsing verbs flow attributes hardware steering specs.

2. Check if flow is multicast - this is required in order to decide
to which flow table will we add the steering rule.

3. Set outer headers in flow match criteria to zeros.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add exports to flow steering API for mlx5_ib usage.
The following functions are exported:

1. mlx5_create_auto_grouped_flow_table - used to create flow
table with auto flow grouping management (create and destroy
flow groups). In auto-grouped flow tables, we create groups
automatically if needed (if we don't find an existing
flow group with same match criteria when we add new rule).

2. mlx5_destroy_flow_table - used to destroy  a flow table.

3. mlx5_add_flow_rule - used to add flow rule into a flow table.

4. mlx5_del_flow_rule - used to delete flow rule from its flow table.

5. mlx5_get_flow_namespace - used to get a handle to the required
namespace sub-tree.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the driver is loaded, we create flow steering namespace
for kernel bypass with nine priorities and another namespace
for leftovers(in order to catch packets that weren't matched).
Verbs applications will use these priorities.
we found nine as a number that balances the requirements from the
user and retains performance.

The bypass namespace is used by verbs applications that want to bypass
the kernel networking stack. The leftovers namespace is used by verbs
applications and the sniffer in order to catch packets that weren't
handled by any preceding rules.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before we create the sub tree of a steering namespaces(kernel, bypass,
leftovers) we check that the device has the required capabilities
in order to create this subtree.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each priority has two attributes:
1. max_ft - maximum allowed flow tables under this priority.
2. start_level - start level range of the flow tables
in the priority.

These attributes are set by traversing the tree nodes by
DFS and set start level and max flow tables to each priority.
Start level depends on the max flow tables of the prior priorities
in the tree.

The leaves of the trees have max_ft set in them. Each node accumulates
the max_ft of its children and set it accordingly.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow tables from different priorities should be chained together.
When a packet arrives we search for a match in the
by-pass flow tables (first we search for a match in priority 0
and if we don't find a match we move to the next priority).
If we can't find a match in any of the bypass flow-tables, we continue
searching in the flow-tables of the next priority, which are the
kernel's flow tables.

Setting the miss flow table in a new flow table to be the next one in
the list is performed via create flow table API. If we want to change an
existing flow table, for example in order to point from an
existing flow table to the new next-in-list flow table, we use the
modify flow table API.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce the modify flow table command. This command is used when
we want to change the next flow table of an existing flow table.
The next flow table is defined as the table we search (in order
to find a match), if we couldn't find a match in any of the flow table
entries in the current flow table.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The root Flow Table for each Flow Table Type is defined,
by default, as the Flow Table with level 0.

In order not to use an empty flow tables and introduce new hops,
but still preserve space for flow-tables that have a priority
greater(lower number) than the current flow table, we introduce this
new set root flow table command.
This command tells the HW to start matching packets from the
assigned root flow table.
This command is used when we create new flow table with level lower than the
current lowest flow table or it is the first flow table.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two utility functions for find next and prev flow table.
Find next flow table function gets priority and return the
first flow table of the next priority in the tree.
Find prev flow table return the last flow table of
the previous priority in the tree.

These utility functions are used for chaining flow table from different
priorities.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When user add rule to autogrouped flow table, we search
for flow group with the same match criteria, if we don't
find such group then we create new flow group with the
required match criteria and insert the rule to this group.

We divide the flow table into required_groups + 1,
in order to reserve a part of the flow table for rules
which don't match any existing group.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code in sh_eth_dev_init()  twiddling the ECMR bits always looked a bit
strange to me:  if one intends to respect 'mdp->duplex', why save old value
of the ECMR.DM bit? As all the other bits are zeroed anyway, we don't really
need to read ECMR before writing to it.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code in ravb_emac_init() twiddling the ECMR bits always looked a bit
strange to me: if one intends to respect 'priv->duplex', why save old value
of the ECMR.DM bit?   As all the other bits are zeroed anyway, we don't
really need to read ECMR before writing to it.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spew in /proc/net/bonding/bond0 uses netif_carrier_ok() to determine
mii_status, while /sys/class/net/bond0/bonding/mii_status looks at
curr_active_slave, which doesn't actually seem to be set sometimes when
the bond actually is up. A mode 4 bond configured via ifcfg-foo files on a
Red Hat Enterprise Linux system, after boot, comes up clean and
functional, but the sysfs node shows mii_status of down, while proc shows
up. A simple enough fix here seems to be to use the same method for
determining up or down in both places, and I'd opt for the one that seems
to match reality.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: netdev@vger.kernel.org
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dumping the FDB (invoked with a process context) or handling FDB
notifications (polled periodicly in delayed work) might each entail
multiple EMAD transcations due to the number of entries.

While we only allow one EMAD transaction at a time, there is nothing
stopping the dump and notification processing sessions from
interleaving. However, this is forbidden by the hardware, so we need to
make sure only one of these sessions can run at a time.

Solve this by adding a mutex ('fdb_lock'), as both kernel threads can
sleep while waiting for the response EMAD.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use phy_find_first() to find the first phy device instead of
open-coding it.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 7f854420 ("phy: Add API for {un}registering an mdio device to
a bus") introduces an API to access mii_bus structures, but missed to
update the TI cpamc driver. This results in the following error message.

drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_probe':
drivers/net/ethernet/ti/cpmac.c:1119:18: error:
	'struct mii_bus' has no member named 'phy_map'

Fixes: 7f854420 ("phy: Add API for {un}registering an mdio device to a bus")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e7f4dc35 ("mdio: Move allocation of interrupts into core")
removes some code from tc_mii_init(), but does not remove a now unused
variable. This results in the following build warning.

drivers/net/ethernet/toshiba/tc35815.c: In function 'tc_mii_init':
drivers/net/ethernet/toshiba/tc35815.c:670:6: warning: unused variable 'i'

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 7f854420 ("phy: Add API for {un}registering an mdio device to
a bus") introduces an API to access mii_bus structures, but missed to
update the tc35815 driver. This results in the following error message.

drivers/net/ethernet/toshiba/tc35815.c: In function 'tc_mii_probe':
drivers/net/ethernet/toshiba/tc35815.c:617:18: error:
	'struct mii_bus' has no member named 'phy_map'
drivers/net/ethernet/toshiba/tc35815.c:623:24: error:
	'struct mii_bus' has no member named 'phy_map'

Instead of looping over the list of phy addresses to find a phy chip,
use phy_find_first(). While the intent of the original code was to return
an error if more than one phy was specified, this code path was never
executed because the loop aborted after finding the first phy. The
original code is therefore semantically identical to phy_find_first(),
thus it is simpler and more straightforward to use phy_find_first()
directly.

Fixes: 7f854420 ("phy: Add API for {un}registering an mdio device to a bus")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LAN8740 has a different phy_id than LAN8710/LAN8720.
Signed-off-by: NJoshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e7f4dc35 ("mdio: Move allocation of interrupts into core")
introduced the following build warnings:

drivers/net/ethernet/nxp/lpc_eth.c: In function 'lpc_mii_init':
drivers/net/ethernet/nxp/lpc_eth.c:865:1: warning: label 'err_out_1' defined but not used [-Wunused-label]
drivers/net/ethernet/nxp/lpc_eth.c:826:20: warning: unused variable 'i' [-Wunused-variable]

Remove the unused variables to fix them.
Reported-by: NOlof's autobuilder <build@lixom.net>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While building blackfin defconfig we were getting a build warning:
warning: label 'out_err_irq_alloc' defined but not used.

Commit e7f4dc35 ("mdio: Move allocation of interrupts into core")
removed the label out_err_mdiobus_register but then mistakenly jumped to
out_err_alloc. But it was actually supposed to jump to out_err_irq_alloc.

Fixes: e7f4dc35 ("mdio: Move allocation of interrupts into core")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The build of blackfin defconfig is failing with the error:
error: 'struct mii_bus' has no member named 'phy_map'

A new API mdiobus_get_phy() was introduced and phy_map was removed but
it was not changed here.

Fixes: 7f854420 ("phy: Add API for {un}registering an mdio device to a bus.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 115b56af ("cxgb4: Update mps_tcam output to include T6
fields") from Dec 23, 2015, leads to the following static checker
warning:

        drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:1735
mps_tcam_show()
        warn: we tested 'lookup_type' before and it was 'true'

Fixing it.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RK3036's GRFs offset are different with RK3066/RK3188, and need to set
mac TX/RX clock before probe emac.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the RK3066/RK3188, there was fixed GRF offset configuration to set emac
and fixed DIV2 mac TX/RX clock. So, we need to easily set and fit to other
SoCs (RK3036) which maybe have different GRF offset, and need adjust mac
TX/RX clock.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After enter arc_emac_probe, emac will get_phy_id, phy_poll_reset and
other connecting PHY via mdiobus_read, so we need to set correct
ref clock rate for emac before probe emac.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use HWRM_FW_RESET command to request a self-reset of the embedded
processor(s) after successfully applying a firmware update. For boot
processor, the self-reset is currently deferred until the next PCIe reset.
Signed-off-by: NRob Swindell <swindell@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For future compatibility, zero pad all messages that the driver sends
to the firmware to 128 bytes.  If these messages are extended in the
future with new byte enables, zero padding these messages now will
guarantee future compatibility.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The warning about being able to read any MDIO device, not just the
attached ethernet devices PHY applies to all MDIO drivers. So remove
it. This also removes a reference to a member in phy_device which has
moved.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a number of build errors due to moving the phy_map and centralizing
interrupt allocation.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use phy_find_first() to find the first phy device instead of
open coding it.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 7f854420 ("phy: Add API for {un}registering an mdio device to
a bus") introduces an API to access mii_bus structures, but missed to
update the sb1250 driver. This results in the following build error.

drivers/net/ethernet/broadcom/sb1250-mac.c: In function 'sbmac_mii_probe':
drivers/net/ethernet/broadcom/sb1250-mac.c:2360:24: error:
	'struct mii_bus' has no member named 'phy_map'

Use phy_find_first() instead of open coding it.

Commit 2220943a ("phy: Centralise print about attached phy") introduces
the following build error.

drivers/net/ethernet/broadcom/sb1250-mac.c: In function 'sbmac_mii_probe':
drivers/net/ethernet/broadcom/sb1250-mac.c:2383:20: error: 'phydev' undeclared

Fixes: 7f854420 ("phy: Add API for {un}registering an mdio device to a bus")
Fixes: 2220943a ("phy: Centralise print about attached phy")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>