The OPAL console driver does not delay in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware.

It can't yet be made to sleep because it is called under spinlock,
but it can be changed to the standard OPAL_BUSY loop form, and a
delay added to keep it from hitting the firmware too frequently.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The intention here is to consume and discard the remaining buffer
upon error. This works if there has not been a previous partial write.
If there has been, then total_len is no longer total number of bytes
to copy. total_len is always "bytes left to copy", so it should be
added to written bytes.

This code may not be exercised any more if partial writes will not be
hit, but this is a small bugfix before a larger change.
Reviewed-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fixes: 8034f715 ("powernv/opal-dump: Convert to irq domain")

Converts all the return explicit number to a more proper IRQ_HANDLED,
which looks proper incase of interrupt handler returning case.

Here, It also removes error message like "nobody cared" which was
getting unveiled while returning -1 or 0 from handler.
Signed-off-by: NMukesh Ojha <mukesh02@linux.vnet.ibm.com>
Reviewed-by: NVasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Moves the return value check of 'opal_dump_info' to a proper place which
was previously unnecessarily filling all the dump info even on failure.
Signed-off-by: NMukesh Ojha <mukesh02@linux.vnet.ibm.com>
Acked-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Since commit dc310669 ("powerpc: tm: Always use fp_state and
vr_state to store live registers") tm_reclaim_thread() doesn't use the
parameter anymore, both callers have to bother getting it as they have
no need for a struct thread_info either.

Just remove it and adjust the callers.
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In commit eb5c3f1c ("powerpc: Always save/restore checkpointed regs
during treclaim/trecheckpoint") __tm_recheckpoint was modified to no
longer take the second parameter 'unsigned long orig_msr' as part of a
TM rewrite to simplify the reclaiming/recheckpointing process.

There is a comment in the asm file where the function is delcared which
has an incorrect prototype with the 'orig_msr' parameter.

This patch corrects the comment.
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch reworked selftest memcmp_64 so that memcmp selftest can
cover more test cases.

It adds testcases for:
- memcmp over 4K bytes size.
- s1/s2 with different/random offset on 16 bytes boundary.
- enter/exit_vmx_ops pairness.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
[mpe: Add -maltivec to fix build on some toolchains]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch is based on the previous VMX patch on memcmp().

To optimize ppc64 memcmp() with VMX instruction, we need to think about
the VMX penalty brought with: If kernel uses VMX instruction, it needs
to save/restore current thread's VMX registers. There are 32 x 128 bits
VMX registers in PPC, which means 32 x 16 = 512 bytes for load and store.

The major concern regarding the memcmp() performance in kernel is KSM,
who will use memcmp() frequently to merge identical pages. So it will
make sense to take some measures/enhancement on KSM to see whether any
improvement can be done here.  Cyril Bur indicates that the memcmp() for
KSM has a higher possibility to fail (unmatch) early in previous bytes
in following mail.
	https://patchwork.ozlabs.org/patch/817322/#1773629
And I am taking a follow-up on this with this patch.

Per some testing, it shows KSM memcmp() will fail early at previous 32
bytes.  More specifically:
    - 76% cases will fail/unmatch before 16 bytes;
    - 83% cases will fail/unmatch before 32 bytes;
    - 84% cases will fail/unmatch before 64 bytes;
So 32 bytes looks a better choice than other bytes for pre-checking.

The early failure is also true for memcmp() for non-KSM case. With a
non-typical call load, it shows ~73% cases fail before first 32 bytes.

This patch adds a 32 bytes pre-checking firstly before jumping into VMX
operations, to avoid the unnecessary VMX penalty. It is not limited to
KSM case. And the testing shows ~20% improvement on memcmp() average
execution time with this patch.

And note the 32B pre-checking is only performed when the compare size
is long enough (>=4K currently) to allow VMX operation.

The detail data and analysis is at:
https://github.com/justdoitqd/publicFiles/blob/master/memcmp/README.mdSigned-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch add VMX primitives to do memcmp() in case the compare size
is equal or greater than 4K bytes. KSM feature can benefit from this.

Test result with following test program(replace the "^>" with ""):
------
># cat tools/testing/selftests/powerpc/stringloops/memcmp.c
>#include <malloc.h>
>#include <stdlib.h>
>#include <string.h>
>#include <time.h>
>#include "utils.h"
>#define SIZE (1024 * 1024 * 900)
>#define ITERATIONS 40

int test_memcmp(const void *s1, const void *s2, size_t n);

static int testcase(void)
{
        char *s1;
        char *s2;
        unsigned long i;

        s1 = memalign(128, SIZE);
        if (!s1) {
                perror("memalign");
                exit(1);
        }

        s2 = memalign(128, SIZE);
        if (!s2) {
                perror("memalign");
                exit(1);
        }

        for (i = 0; i < SIZE; i++)  {
                s1[i] = i & 0xff;
                s2[i] = i & 0xff;
        }
        for (i = 0; i < ITERATIONS; i++) {
		int ret = test_memcmp(s1, s2, SIZE);

		if (ret) {
			printf("return %d at[%ld]! should have returned zero\n", ret, i);
			abort();
		}
	}

        return 0;
}

int main(void)
{
        return test_harness(testcase, "memcmp");
}
------
Without this patch (but with the first patch "powerpc/64: Align bytes
before fall back to .Lshort in powerpc64 memcmp()." in the series):
	4.726728762 seconds time elapsed                                          ( +-  3.54%)
With VMX patch:
	4.234335473 seconds time elapsed                                          ( +-  2.63%)
		There is ~+10% improvement.

Testing with unaligned and different offset version (make s1 and s2 shift
random offset within 16 bytes) can archieve higher improvement than 10%..
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Some old tool chains don't know about instructions like vcmpequd.

This patch adds .long macro for vcmpequd and vcmpequb, which is
a preparation to optimize ppc64 memcmp with VMX instructions.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently memcmp() 64bytes version in powerpc will fall back to .Lshort
(compare per byte mode) if either src or dst address is not 8 bytes aligned.
It can be opmitized in 2 situations:

1) if both addresses are with the same offset with 8 bytes boundary:
memcmp() can compare the unaligned bytes within 8 bytes boundary firstly
and then compare the rest 8-bytes-aligned content with .Llong mode.

2)  If src/dst addrs are not with the same offset of 8 bytes boundary:
memcmp() can align src addr with 8 bytes, increment dst addr accordingly,
 then load src with aligned mode and load dst with unaligned mode.

This patch optmizes memcmp() behavior in the above 2 situations.

Tested with both little/big endian. Performance result below is based on
little endian.

Following is the test result with src/dst having the same offset case:
(a similar result was observed when src/dst having different offset):
(1) 256 bytes
Test with the existing tools/testing/selftests/powerpc/stringloops/memcmp:
- without patch
	29.773018302 seconds time elapsed                                          ( +- 0.09% )
- with patch
	16.485568173 seconds time elapsed                                          ( +-  0.02% )
		-> There is ~+80% percent improvement

(2) 32 bytes
To observe performance impact on < 32 bytes, modify
tools/testing/selftests/powerpc/stringloops/memcmp.c with following:
-------
 #include <string.h>
 #include "utils.h"

-#define SIZE 256
+#define SIZE 32
 #define ITERATIONS 10000

 int test_memcmp(const void *s1, const void *s2, size_t n);
--------

- Without patch
	0.244746482 seconds time elapsed                                          ( +-  0.36%)
- with patch
	0.215069477 seconds time elapsed                                          ( +-  0.51%)
		-> There is ～+13% improvement

(3) 0~8 bytes
To observe <8 bytes performance impact, modify
tools/testing/selftests/powerpc/stringloops/memcmp.c with following:
-------
 #include <string.h>
 #include "utils.h"

-#define SIZE 256
-#define ITERATIONS 10000
+#define SIZE 8
+#define ITERATIONS 1000000

 int test_memcmp(const void *s1, const void *s2, size_t n);
-------
- Without patch
       1.845642503 seconds time elapsed                                          ( +- 0.12% )
- With patch
       1.849767135 seconds time elapsed                                          ( +- 0.26% )
		-> They are nearly the same. (-0.2%)
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch adds error reporting to H_ENTER and H_READ hcalls. A
failure for both these hcalls are mostly fatal and it would be good to
log the failure reason.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Split out of larger patch]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Switch from printk to pr_fmt() / pr_xxx().
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Split out of larger patch]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We do this in some part. This patch make sure we always try to search
for hpte without holding lock and redo the compare with lock held once
match found.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

No functional change
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When computing the starting slot number for a hash page table group we used
to do this
hpte_group = ((hash & htab_hash_mask) * HPTES_PER_GROUP) & ~0x7UL;

Multiplying with 8 (HPTES_PER_GROUP) imply the last three bits are 0. Hence we
really don't need to clear then separately.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We do this only with VMEMMAP config so that our page_to_[nid/section] etc are not
impacted.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

With SPARSEMEM config enabled, we make sure that we don't add sections beyond
MAX_PHYSMEM_BITS range. This results in not building vmemmap mapping for
range beyond max range. But our memblock layer looks the device tree and create
mapping for the full memory range. Prevent this by checking against
MAX_PHSYSMEM_BITS when doing memblock_add.

We don't do similar check for memeblock_reserve_range. If reserve range is beyond
MAX_PHYSMEM_BITS we expect that to be configured with 'nomap'. Any other
reserved range should come from existing memblock ranges which we already
filtered while adding.

This avoids crash as below when running on a system with system ram config above
MAX_PHSYSMEM_BITS

 Unable to handle kernel paging request for data at address 0xc00a001000000440
 Faulting instruction address: 0xc000000001034118
 cpu 0x0: Vector: 300 (Data Access) at [c00000000124fb30]
     pc: c000000001034118: __free_pages_bootmem+0xc0/0x1c0
     lr: c00000000103b258: free_all_bootmem+0x19c/0x22c
     sp: c00000000124fdb0
    msr: 9000000002001033
    dar: c00a001000000440
  dsisr: 40000000
   current = 0xc00000000120dd00
   paca    = 0xc000000001f60000^I irqmask: 0x03^I irq_happened: 0x01
     pid   = 0, comm = swapper
 [c00000000124fe20] c00000000103b258 free_all_bootmem+0x19c/0x22c
 [c00000000124fee0] c000000001010a68 mem_init+0x3c/0x5c
 [c00000000124ff00] c00000000100401c start_kernel+0x298/0x5e4
 [c00000000124ff90] c00000000000b57c start_here_common+0x1c/0x520
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Similarly as we just did for 32-bit, add phony targets for generating
a little endian and Book3E allmodconfig. These aren't covered by the
regular allmodconfig, which is big endian and Book3S due to the way
the Kconfig symbols are structured.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Because the allmodconfig logic just sets every symbol to M or Y, it
has the effect of always generating a 64-bit config, because
CONFIG_PPC64 becomes Y.

So to make it easier for folks to test 32-bit code, provide a phony
defconfig target that generates a 32-bit allmodconfig.

The 32-bit port has several mutually exclusive CPU types, we choose
the Book3S variants as that's what the help text in Kconfig says is
most common.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When I added the spectre_v2 information in sysfs, I included the
availability of the ori31 speculation barrier.

Although the ori31 barrier can be used to mitigate v2, it's primarily
intended as a spectre v1 mitigation. Spectre v2 is mitigated by
hardware changes.

So rework the sysfs files to show the ori31 information in the
spectre_v1 file, rather than v2.

Currently we display eg:

  $ grep . spectre_v*
  spectre_v1:Mitigation: __user pointer sanitization
  spectre_v2:Mitigation: Indirect branch cache disabled, ori31 speculation barrier enabled

After:

  $ grep . spectre_v*
  spectre_v1:Mitigation: __user pointer sanitization, ori31 speculation barrier enabled
  spectre_v2:Mitigation: Indirect branch cache disabled

Fixes: d6fbe1c5 ("powerpc/64s: Wire up cpu_show_spectre_v2()")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There is an asynchronous aspect to smp_send_nmi_ipi. The caller waits
for all CPUs to call in to the handler, but it does not wait for
completion of the handler. This is a needless complication, so remove
it and always wait synchronously.

The synchronous wait allows the caller to easily time out and clear
the wait for completion (zero nmi_ipi_busy_count) in the case of badly
behaved handlers. This would have prevented the recent smp_send_stop
NMI IPI bug from causing the system to hang.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When the masked interrupt handler clears MSR[EE] for an interrupt in
the PACA_IRQ_MUST_HARD_MASK set, it does not set PACA_IRQ_HARD_DIS.
This makes them get out of synch.

With that taken into account, it's only low level irq manipulation
(and interrupt entry before reconcile) where they can be out of synch.
This makes the code less surprising.

It also allows the IRQ replay code to rely on the IRQ_HARD_DIS value
and not have to mtmsrd again in this case (e.g., for an external
interrupt that has been masked). The bigger benefit might just be
that there is not such an element of surprise in these two bits of
state.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The test case assumes execute-permissions of unallocated keys are
enabled by default, which is incorrect.
Reviewed-by: NThiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Only when the key is allocated, its permission are enabled.
Reviewed-by: NThiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Applications need the ability to associate an address-range with some
key and latter revert to its initial default key. Pkey-0 comes close to
providing this function but falls short, because the current
implementation disallows applications to explicitly associate pkey-0 to
the address range.

Lets make pkey-0 less special and treat it almost like any other key.
Thus it can be explicitly associated with any address range, and can be
freed. This gives the application more flexibility and power.  The
ability to free pkey-0 must be used responsibily, since pkey-0 is
associated with almost all address-range by default.

Even with this change pkey-0 continues to be slightly more special
from the following point of view.
(a) it is implicitly allocated.
(b) it is the default key assigned to any address-range.
(c) its permissions cannot be modified by userspace.

NOTE: (c) is specific to powerpc only. pkey-0 is associated by default
with all pages including kernel pages, and pkeys are also active in
kernel mode. If any permission is denied on pkey-0, the kernel running
in the context of the application will be unable to operate.

Tested on powerpc.
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
[mpe: Drop #define PKEY_0 0 in favour of plain old 0]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

execute-only key is allocated dynamically. This is a problem. When a
thread implicitly creates an execute-only key, and resets the UAMOR
for that key, the UAMOR value does not percolate to all the other
threads. Any other thread may ignorantly change the permissions on the
key. This can cause the key to be not execute-only for that thread.

Preallocate the execute-only key and ensure that no thread can change
the permission of the key, by resetting the corresponding bit in
UAMOR.

Fixes: 5586cf61 ("powerpc: introduce execute-only pkey")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Total number of pkeys calculation is off by 1. Fix it.

Fixes: 4fb158f6 ("powerpc: track allocation status of all pkeys")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When a thread forks the contents of AMR, IAMR, UAMOR registers in the
newly forked thread are not inherited.

Save the registers before forking, for content of those
registers to be automatically copied into the new thread.

Fixes: cf43d3b2 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Key allocation and deallocation has the side effect of programming the
UAMOR/AMR/IAMR registers. This is wrong, since its the responsibility of
the application and not that of the kernel, to modify the permission on
the key.

Do not modify the pkey registers at key allocation/deallocation.

This patch also fixes a bug where a sys_pkey_free() resets the UAMOR
bits of the key, thus making its permissions unmodifiable from user
space. Later if the same key gets reallocated from a different thread
this thread will no longer be able to change the permissions on the key.

Fixes: cf43d3b2 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: NThiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Deny all permissions on all keys, with some exceptions. pkey-0 must
allow all permissions, or else everything comes to a screaching halt.
Execute-only key must allow execute permission.

Fixes: cf43d3b2 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently in a multithreaded application, a key allocated by one
thread is not usable by other threads. By "not usable" we mean that
other threads are unable to change the access permissions for that
key for themselves.

When a new key is allocated in one thread, the corresponding UAMOR
bits for that thread get enabled, however the UAMOR bits for that key
for all other threads remain disabled.

Other threads have no way to set permissions on the key, and the
current default permissions are that read/write is enabled for all
keys, which means the key has no effect for other threads. Although
that may be the desired behaviour in some circumstances, having all
threads able to control their permissions for the key is more
flexible.

The current behaviour also differs from the x86 behaviour, which is
problematic for users.

To fix this, enable the UAMOR bits for all keys, at process
creation (in start_thread(), ie exec time). Since the contents of
UAMOR are inherited at fork, all threads are capable of modifying the
permissions on any key.

This is technically an ABI break on powerpc, but pkey support is fairly
new on powerpc and not widely used, and this brings us into
line with x86.

Fixes: cf43d3b2 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Tested-by: NFlorian Weimer <fweimer@redhat.com>
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
[mpe: Reword some of the changelog]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This logic was shared between multiple tests, but now that we have
removed all but one of them we can just move it into that test.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Paste on POWER9 only works to accelerators and not on real memory. So
these tests just generate a SIGILL.

So just delete them.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This is a test of the ISA 3.0 "copy" instruction. That instruction has
an L field, which if set to 1 specifies that "the instruction
identifies the beginning of a move group" (pp 858). That's also
referred to as "copy first" vs "copy".

In ISA 3.0B the copy instruction does not have an L field, and the
corresponding bit in the instruction must be set to 1.

This test is generating a "copy" instruction, not a "copy first", and
so on Power9 (which implements 3.0B), this results in an illegal
instruction.

So just drop the test entirely. We still have copy_first_unaligned to
test the "copy first" behaviour.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This property was added in 2004 and the only use of it, which was
already inside `#if 0`, was removed a month later.
Signed-off-by: NMurilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Set the coherent_dma_mask for the PS3 ehci, ohci, and snd devices.

Silences WARN_ON_ONCE messages emitted by the dma_alloc_attrs() routine.
Reported-by: NFredrik Noring <noring@nocrew.org>
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Function atomic_inc_unless_negative() returns a bool to indicate
success/failure. However cxl_adapter_context_get() wrongly compares
the return value against '>=0' which will always be true. The patch
fixes this comparison to '==0' there by also fixing this compile time
warning:

	drivers/misc/cxl/main.c:290 cxl_adapter_context_get()
	warn: 'atomic_inc_unless_negative(&adapter->contexts_num)' is unsigned

Fixes: 70b565bb ("cxl: Prevent adapter reset if an active context exists")
Cc: stable@vger.kernel.org # v4.9+
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NVaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: NFrederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The threshold at which it becomes more efficient to coalesce a range
of ATSDs into a single per-PID ATSD is currently not well understood
due to a lack of real-world work loads. This patch adds a debugfs
parameter allowing the threshold to be altered at runtime in order to
aid future development and refinement of the value.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Acked-by: NBalbir Singh <bsingharora@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

I no longer have any hardware with the Apple motion sensor and thus
relinquish maintainership of the driver.

Remove the maintainers entry entirely, meaning the code will now fall
under "LINUX FOR POWER MACINTOSH".
Signed-off-by: NMichael Hanselmann <linux-kernel@hansmi.ch>
[mpe: Drop the entry entirely, munge change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>