Set up the data structures to be used by the ipsec offload.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add in the code for running and stopping the hardware ipsec
encryption/decryption engine.  It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a few routines to make access to the ipsec registers just a little
easier, and throw in the beginnings of an initialization.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization.  Also recognise the bit-definition
overlap in the error mask macro.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similarly to tx ring, xdp_rxq_info is only registered
when !tfile->detached, so we need to avoid calling
xdp_rxq_info_unreg() twice too. The helper tun_cleanup_tx_ring()
already checks for this properly, so it is correct to put
xdp_rxq_info_unreg() just inside there.

Reported-by: syzbot+1c788d7ce0f0888f1d7f@syzkaller.appspotmail.com
Fixes: 8565d26b ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: sched: add extack support for cls offloads

I've dropped the tests from the series because test_offloads.py changes
will conflict with bpf-next patches.  I will send four more patches with
tests once bpf-next is merged back, hopefully still making it into 4.16 :)

v4:
 - rebase on top of Alex's changes.

---

Quentin says:

This series tries to improve user experience when eBPF hardware offload
hits error paths at load time. In particular, it introduces netlink
extended ack support in the nfp driver.

To that aim, transmission of the pointer to the extack object is piped
through the `change()` operation of the existing classifiers (patch 1 to
6). Then it is used for TC offload in the nfp driver (patch 8) and in
netdevsim (patch 9, selftest in patch 10). Patch 7 adds a helper to handle
extack messages in the core when TC offload is disabled on the net device.

For completeness extack is propagated for classifiers other than cls_bpf,
but it's up to the drivers to make use of it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the recently added extack support for eBPF offload in the driver.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass a pointer to an extack object to nfp_app_xdp_offload() in order to
prepare for extack usage in the nfp driver. Next step will be to forward
this extack pointer to nfp_net_bpf_offload(), once this function is able
to use it for printing error messages.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a wrapper around tc_can_offload() that takes an additional
extack pointer argument in order to output an error message if TC
offload is disabled on the device.

In this way, the error message is handled by the core and can be the
same for all drivers.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add extack support for hardware offload of classifiers. In order
to achieve this, a pointer to a struct netlink_ext_ack is added to the
struct tc_cls_common_offload that is passed to the callback for setting
up the classifier. Function tc_cls_common_offload_init() is updated to
support initialization of this new attribute.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the extack pointer obtained in the `->change()` filter operation to
cls_bpf_offload() and then to cls_bpf_offload_cmd(). This makes it
possible to use this extack pointer in drivers offloading BPF programs
in a future patch.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_u32. This makes it
possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_matchall. This makes
it possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_flower. This makes it
possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we no longer localize channel/CPU affiliation within one NUMA
node, num_online_cpus() is used as the number of channel cap, instead of
the number of processors in a NUMA node.

This patch allows a bigger range for tuning the number of channels.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spaces were mistakenly used instead of tabs in some of the code related
to reset functionality, which caused checkpatch.pl errors. These were
missed earlier so fixing them now.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T3 devices have different ports on same PCI function,
so using dev_port to identify ports.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return statements in functions returning bool should use
true/false instead of 1/0.

This issue was detected with the help of Coccinelle.

Fixes: 85b35269 ("bridge: Fix build error when IGMP_SNOOPING is not enabled")
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom tags inserted by Broadcom switches put a 4 byte header after
the MAC SA and before the EtherType, which may look like some sort of 0
length LLC/SNAP packet (tcpdump and wireshark do think that way). With
ACS enabled in stmmac the packets were truncated to 8 bytes on
reception, whereas clearing this bit allowed normal reception to occur.

In order to make that possible, we need to pass a net_device argument to
the different core_init() functions and we are dependent on the Broadcom
tagger padding packets correctly (which it now does). To be as little
invasive as possible, this is only done for gmac1000 when the network
device is DSA-enabled (netdev_uses_dsa() returns true).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Peng Li says:

====================
add some features to hns3 driver

This patchset adds some features to hns3 driver, include the support
for ethtool command -d, -p and support for manager table.

[Patch 1/4] adds support for ethtool command -d, its ops is get_regs.
driver will send command to command queue, and get regs number and
regs value from command queue.
[Patch 2/4] adds manager table initialization for hardware.
[Patch 3/4] adds support for ethtool command -p. For fiber ports, driver
sends command to command queue, and IMP will write SGPIO regs to control
leds.
[Patch 4/4] adds support for net status led for fiber ports. Net status
include  port speed, total rx/tx packets and link status. Driver send
the status to command queue, and IMP will write SGPIO to control leds.

---
Change log:
V1 -> V2:
1, fix comments from Andrew Lunn, remove the patch "net: hns3: add
ethtool -p support for phy device".
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check the net status per second, include port speed, total rx/tx packets
and link status. Updating the led status for fiber port.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add led location support for fiber port. The led will keep blinking
when locating.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The manager table is empty by default. If it is not initialized, the
management pkgs like LLDP will be dropped by hardware. Default entries
need to be added to manager table.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds get_regs support for ethtool cmd.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expose the number of times the link has been going UP or DOWN, and
update the "carrier_changes" counter to be the sum of these two events.
While at it, also update the sysfs-class-net documentation to cover:
carrier_changes (3.15), carrier_up_count (4.16) and carrier_down_count
(4.16)
Signed-off-by: NDavid Decotigny <decot@googlers.com>
[Florian:
* rebase
* add documentation
* merge carrier_changes with up/down counters]
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ccfdec90 ("macsec: Add support for GCM-AES-256 cipher suite")
changed a few values in the uapi headers for MACsec.

Because of existing userspace implementations, we need to preserve the
value of MACSEC_DEFAULT_CIPHER_ID. Not doing that resulted in
wpa_supplicant segfaults when a secure channel was created using the
default cipher. Thus, swap MACSEC_DEFAULT_CIPHER_{ID,ALT} back to their
original values.

Changing the maximum length of the MACSEC_SA_ATTR_KEY attribute is
unnecessary, as the previous value (MACSEC_MAX_KEY_LEN, which was 128B)
is large enough to carry 32-bytes keys. This patch reverts
MACSEC_MAX_KEY_LEN to 128B and restores the old length check on
MACSEC_SA_ATTR_KEY.

Fixes: ccfdec90 ("macsec: Add support for GCM-AES-256 cipher suite")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When !CONFIG_REGMAP hns throws compiler warnings since
dsaf_read_syscon ignores the return result from regmap_read,
which allows val to be uninitialized.

Fixes: 86897c96 ("net: hns: add syscon operation for dsaf")
Reported-by: NJason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The i.MX8 is a ARMv8 based SoC, that uses the same FEC IP as the
earlier, ARMv7 based, i.MX SoCs. Allow the driver to work on ARM64.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main purpose of this patch is adding a way of checking per-queue stats.
It's useful to debug performance problems on multiqueue environment.

$ ethtool -S ens10
NIC statistics:
     rx_queue_0_packets: 2090408
     rx_queue_0_bytes: 3164825094
     rx_queue_1_packets: 2082531
     rx_queue_1_bytes: 3152932314
     tx_queue_0_packets: 2770841
     tx_queue_0_bytes: 4194955474
     tx_queue_1_packets: 3084697
     tx_queue_1_bytes: 4670196372

This change converts existing per-cpu stats structure into per-queue one.
This should not impact on performance since each queue counter is not
updated concurrently by multiple cpus.

Performance numbers:
 - Guest has 2 vcpus and 2 queues
 - Guest runs netserver
 - Host runs 100-flow super_netperf

                     Before      After       Diff
UDP_STREAM 18byte        86.22       87.00   +0.90%
UDP_STREAM 1472byte    4055.27     4042.18   -0.32%
TCP_STREAM            16956.32    16890.63   -0.39%
UDP_RR               178667.11   185862.70   +4.03%
TCP_RR               128473.04   124985.81   -2.71%
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcin Wojtas says:

====================
Armada 7k/8k PP2 ACPI support

I quickly resend the series, thanks to Antoine Tenart's remark,
who spotted !CONFIG_ACPI compilation issue after introducing
the new fwnode_irq_get() routine. Please see the details in the changelog
below and the 3/7 commit log.

mvpp2 driver can work with the ACPI representation, as exposed
on a public branch:
https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/marvell-armada-wip
It was compiled together with the most recent Tianocore EDK2 revision.
Please refer to the firmware build instruction on MacchiatoBin board:
http://wiki.macchiatobin.net/tiki-index.php?page=Build+from+source+-+UEFI+EDK+II

ACPI representation of PP2 controllers (withouth PHY support) can
be viewed in the github:
* MacchiatoBin:
https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/blob/71ae395da1661374b0f07d1602afb1eee56e9794/Platforms/Marvell/Armada/AcpiTables/Armada80x0McBin/Dsdt.asl#L201

* Armada 7040 DB:
https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/blob/71ae395da1661374b0f07d1602afb1eee56e9794/Platforms/Marvell/Armada/AcpiTables/Armada70x0/Dsdt.asl#L131

I will appreciate any comments or remarks.

Best regards,
Marcin

Changelog:
v3 -> v4:
* 3/7
    - add new macro (ACPI_HANDLE_FWNODE) and fix
      compilation with !CONFIG_ACPI
    - extend commit log and mention usability of fwnode_irq_get
      for the child nodes as well

v2 -> v3:
* 1/7, 2/7
    - Add Rafael's Acked-by's
* 3/7, 4/7
    - New patches
* 6/7, 7/7
    - Update driver with new helper routines usage
    - Improve commit log.

v1 -> v2:
* Remove MDIO patches
* Use PP2 ports only with link interrupts
* Release second region resources in mvpp2 driver (code moved from
  mvmdio), as explained in details in 5/5 commit message.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces an alternative way of obtaining resources - via
ACPI tables provided by firmware. Enabling coexistence with the DT
support, in addition to the OF_*->device_*/fwnode_* API replacement,
required following steps to be taken:

* Add mvpp2_acpi_match table
* Omit clock configuration and obtain tclk from the property - in ACPI
  world, the firmware is responsible for clock maintenance.
* Disable comphy and syscon handling as they are not available for ACPI.
* Modify way of obtaining interrupts - use newly introduced
  fwnode_irq_get() routine
* Until proper MDIO bus and PHY handling with ACPI is established in the
  kernel, use only link interrupts feature in the driver. For the RGMII
  port it results in depending on GMAC settings done during firmware
  stage.
* When booting with ACPI MVPP2_QDIST_MULTI_MODE is picked by
  default, as there is no need to keep any kind of the backward
  compatibility.

Moreover, a memory region used by mvmdio driver is usually placed in
the middle of the address space of the PP2 network controller.
The MDIO base address is obtained without requesting memory region
(by devm_ioremap() call) in mvmdio.c, later overlapping resources are
requested by the network driver, which is responsible for avoiding
a concurrent access.

In case the MDIO memory region is declared in the ACPI, it can
already appear as 'in-use' in the OS. Because it is overlapped by second
region of the network controller, make sure it is released, before
requesting it again. The care is taken by mvpp2 driver to avoid
concurrent access to this memory region.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OF functions can be used only for the driver using DT.
As a preparation for introducing ACPI support in mvpp2
driver, use struct fwnode_handle in order to obtain
properties from the hardware description.

This patch replaces of_* function with device_*/fwnode_*
where possible in the mvpp2.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'port_count' field of the mvpp2 structure holds an overall amount
of available ports, based on DT nodes status. In order to be prepared
to support other HW description, obtain the value by incrementing it
upon each successful port initialization. This allowed for simplifying
port indexing in the controller's private array, whose size is now not
dynamically allocated, but fixed to MVPP2_MAX_PORTS.

This patch simplifies creating and filling list of enabled ports and
is a part of the preparation for adding ACPI support in the mvpp2 driver.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement a new helper function fwnode_get_next_available_child_node(),
which enables obtaining next enabled child fwnode, which
works on a similar basis to OF's of_get_next_available_child().

This commit also introduces a macro, thanks to which it is
possible to iterate over the available fwnodes, using the
new function described above.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now there were two very similar functions allowing
to get Linux IRQ number from ACPI handle (acpi_irq_get())
and OF node (of_irq_get()). The first one appeared to be used
only as a subroutine of platform_irq_get(), which (in the generic
code) limited IRQ obtaining from _CRS method only to nodes
associated to kernel's struct platform_device.

This patch introduces a new helper routine - fwnode_irq_get(),
which allows to get the IRQ number directly from the fwnode
to be used as common for OF/ACPI worlds. It is usable not
only for the parents fwnodes, but also for the child nodes
comprising their own _CRS methods with interrupts description.

In order to be able o satisfy compilation with !CONFIG_ACPI
and also simplify the new code, introduce a helper macro
(ACPI_HANDLE_FWNODE), with which it is possible to reach
an ACPI handle directly from its fwnode.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now there were two almost identical functions for
obtaining network PHY mode - of_get_phy_mode() and,
more generic, device_get_phy_mode(). However it is not uncommon,
that the network interface is represented as a child
of the actual controller, hence it is not associated
directly to any struct device, required by the latter
routine.

This commit allows for getting the PHY mode for
children nodes in the ACPI world by introducing a new function -
fwnode_get_phy_mode(). This commit also changes
device_get_phy_mode() routine to be its wrapper, in order
to prevent unnecessary duplication.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now there were two almost identical functions for
obtaining MAC address - of_get_mac_address() and, more generic,
device_get_mac_address(). However it is not uncommon,
that the network interface is represented as a child
of the actual controller, hence it is not associated
directly to any struct device, required by the latter
routine.

This commit allows for getting the MAC address for
children nodes in the ACPI world by introducing a new function -
fwnode_get_mac_address(). This commit also changes
device_get_mac_address() routine to be its wrapper, in order
to prevent unnecessary duplication.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer pfrm is initialized and then later re-assigned the same
value and hence the second assignment is redundant and can be removed.

Cleans up clang warning:
drivers/net/caif/caif_hsi.c:222:6: warning: Value stored to 'pfrm'
during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add geneve segmentation offload support of T6 cards.

Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2018-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Less than a handful of changes:
 * possible memory leak fix in hwsim
 * speed up hwsim
 * add hwsim userspace rate control API
 * code cleanups
====================

A conflict was resolved in mac80211_hwsim.c, mostly of
the simple overlapping changes category.  One adding
a rhashtable and another adding a workqueue.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>